• 한국소음진동공학회논문집
• /
• 제23권3호
• /
• pp.274-281
• /
• 2013

Field measurement method of heavy/soft impact sound pressure level which is regulated in JIS and ISO has been using in Korea, Japan and Canada. It is reported that heavy/soft impact sound pressure level was varied by the sound field condition of receiving room such as sound absorption power and room volume. In this study, it is checked that heavy/soft impact sound pressure level was affected by the receiving sound field condition. Rubber ball and bang machine sound pressure level was measured in the vertically connected reverberation chamber. In oder to check the effect of receiving sound field on heavy/soft impact sound pressure, sound absorption power was changed with polyester sound absorption blankets with air space and glass wool. The reverberation time at 1 kHz band was changed from 10 s to 0.2 s by sound absorption material. Rubber ball sound pressure level measured without sound absorption material was 58 dB in $L_{i,Fmax,AW}$, but the level was 46 dB with sound absorption treatment. From this result, it is confirmed that sound field correction method is needed in the heavy/soft impact sound pressure level measurement method using bang machine and rubber ball.

• 한국안전학회지
• /
• 제30권6호
• /
• pp.40-47
• /
• 2015

In this study, temperature characteristics and fire damage form were analyzed to investigate flame spreading form and fire probability from ignition sources subject to drivit component materials which is finishing material in architecture. Ignition sources were limited to a gas torch and exterior panel board fire, and the size of the sample was manufacture in 30 cm length ${\times}$ 50 cm height ${\times}$ 5cm thickness size. Marble (inner wall) + 3 mm drivit (outer wall), marble (inner wall) + 4 mm plaster stone (outer wall), sandwich panel + 3 mm driver bit (outer wall), sandwich panel + 3 mm driver bit + insulation (outer wall), and gypsum board (inner wall) + 3 mm drivit (outer wall) were prepared for the sample. As result of the research for temperature characteristics, large temperature difference by each material was shown in $218^{\circ}C{\sim}995^{\circ}C$ at 30 seconds and $501^{\circ}C{\sim}1078^{\circ}C$ at 300 seconds. Especially when the inner wall was a plaster board, lowest temperature of $501^{\circ}C$ was shown at 300 seconds and marble inner wall showed the following lowest temperature of $900^{\circ}C$. Temperature rising over $1000^{\circ}C$ was shown in other materials. Regarding fire damage form, drivit or gypsum board outer wall parts exposed to fire showed combustion and carbonization to show calcination(breaking phenomenon) and influence of heat exposure was higher as calcination became more severe.

• 한국산업보건학회지
• /
• 제22권2호
• /
• pp.119-127
• /
• 2012

Objectives: The aim of this study is to identify concentration characteristics of indoor and outdoor airborne total fiber particles and asbestos in Gyeongnam Provinces. Methods: This study investigated concentration characteristics of indoor fiber particles from 748 schools and 38 public facilities as well as outdoor particles from 11 sites through PCM (phase contrast microscope). SEM/EDX (scanning electron microscope/energy dispersive using X-ray analysis) was used to obtain physicochemical information of asbestos fiber particles. The study identified asbestos rate in the 15 samples from indoor and outdoor airborne total fiber particles. Results: 1. The average indoor airborne concentrations of total fiber particles were $0.0011{\pm}0007$ f/cc in schools and $0.0015{\pm}0007$ f/cc in public facilities by PCM. Over 90% of the fiber particles were identified as single fibers. 2. The average outdoor airborne concentrations of total fiber particles were $0.0007{\pm}0002$ f/cc, and they were lower than those of indoor airborne concentrations. 3. The results showed that the form of asbestiform was diverse as skein of thread like form and long needle, which was relatively narrower than that of glass fiber and rock wool. 4. The results of SEM/EDX analysis of 15 areas where total fiber particle was relatively high showed that the form was rather similar to that of asbestos, but chemical composition was proven to be non-asbestos. Conclusions: The concentration of indoor and outdoor airborne total fiber particles of Gyeongnam Provinces satisfied the IAQ (Indoor air quality) level of 0.01 f/cc and asbestos was not found in most of the samples by SEM/EDX.

• 한국해양공학회지
• /
• 제30권5호
• /
• pp.349-355
• /
• 2016

Divinycell, which functions as both insulation and a supporting structure, is generally applied in the NO96-type liquefied natural gas (LNG) insulation system. Polymer-material-based Divinycell, which has a high strength and low weight, has been widely used in the offshore, transportation, wind power generation, and civil engineering fields. In particular, this type of material receives attention as an insulation material because its thermal conductivity can be lowered depending on the ambient temperature. However, it is difficult to obtain research results for Divinycell, even though the component materials of the NO96-type LNG cargo containment system, such as 36% nickel steel (invar steel), plywood, perlite, and glass wool, have been extensively studied and reported. In the present study, temperature and strain-rate dependent compressive tests on Divinycell were performed. Both the quantitative experimental data and elastic recovery are discussed. Finally, the mechanical characteristics of Divinycell were compared to the results of polyurethane foam insulation material.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 가을학술발표대회논문집
• /
• pp.43-44
• /
• 2023

Fire doors installed to prevent the spread of fire in buildings are made of paper honeycomb, glass wool, and other materials. Due to their high water absorption rate, they absorb ambient moisture and degrade, and their increased weight causes them to sag internally, creating voids that can warp in the event of a fire and allow flames to pass through. To overcome these issues, research is being conducted on the physical performance of lightweight aerated concrete. However, there is a lack of research on how to ensure fire resistance. Therefore, in this study, the backside temperature of lightweight aerated concrete formulations was measured and compared and analyzied with the physical performance. Since it is difficult to achieve low density by saturation alone, aerated concrete with EPS was produced, which resulted in a density reduction of 24'26%, but the strength increase per unit cement increase was 5'25%, which tended to be lower than the formulation without EPS. The results showed that the lightweight aerated concrete with EPS was 130~140℃ lower than the lightweight aerated concrete with EPS, which is believed to be due to the melting point of EPS delayed the heat diffusion. In the future, wo plan to conduct research to identify the optimal formulation for fire door core materials by varying the amount of EPS added and using industrial by-products to increase long-term strength.

• 한국산업보건학회지
• /
• 제10권1호
• /
• pp.104-114
• /
• 2000

This study was carried out to estimate current status of dust concentrations in the factories producing non-metallic products in Korea. Data were gathered from the environmental monitoring reports by 40 workplace environmental monitoring institutes and the questionnaire designed for the study by the authors. A total of 1838 dust samples from 368 plants were obtained from the reports and were analyzed with no data modifications. But data on asbestos, rock wool, and welding fumes were excluded in this evaluation. The factories were classified into eight groups according to the standard industrial classification scheme in Korea. The results of this study were as follows; 1. The factories included were glass, non-refractory ceramic, refractory ceramic ware, structural non-refractory clay and ceramic, cement and lime, articles of concretes, and stone. Mean(geometric mean) concentrations of total dust samples ranged from $1.75(0.84)mg/m^3$ to $5.87(2.84)mg/m^3$. Statistically significantly higher dust concentrations were found in the cement and lime industries compared with other industries. 2. The non-compliance rates were 15.2% in glass and 20.6% in other non-metallic mineral products industries. Although all institutions surveyed utilized the identical sampling and classification scheme for dusts as specified in the current occupational exposure limits, wide discrepancies were found in collecting samples and classifying dusts. Further problems were discovered in classifying dusts. A dust sample collected could be classified into any of the three groups regardless of silica content. The results of this study showed that dust concentrations in the non-metallic products industries varied widely. Also discovered was classification errors of dust types among workplace monitoring institutes. These errors could adversely affect the results of exposure assessments and the true nature of dust hazards. Further, no institutions performed respirable dust sampling and analysis of crystalline silica. In order to correct these malpractices, current standards of occupational exposure limits should be revised and tight supervision by the Ministry of Labour be suggested.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.127.1-127.1
• /
• 2011

In this paper, ZnO:Al thin films with c-axis preferred orientation were prepared on Soda lime glass substrates by RF magnetron sputtering technique. AZO thin film were prepared in order to clarify optimum conditions for growth of the thin film depending upon process, and then by changing a number of deposition conditions and substrate temperature conditions variously, structural and electrical characteristics were measured. For the manufacture of the AZO were vapor-deposited in the named order. It is well-known that post-annealing is an important method to improve crystal quality. For the annealing process, the dislocation nd other defects arise in the material and adsorption/decomposition occurs. The XRD patterns of the AZO films deposited with grey theory prediction design, annealed in a vacuum ambient($2.0{\times}10-3$Torr)at temperatures of 200, 300, 400 and $500^{\circ}C$ for a period of 30min. The diffraction patterns of all the films show the AZO films had a hexagonal wurtzite structure with a preferential orientation along the c-axis perpendicular to the substrate surface. As can be seen, the (002)peak intensities of the AZO films became more intense and sharper when the annealing temperature increased. On the other hand, When the annealing temperature was $500^{\circ}C$ the peak intensity decreased. The surface morphologies and surface toughness of films were examined by atomic force microscopy(AFM, XE-100, PSIA). Electrical resistivity, Gall mobility and carrier concentration were measured by Hall effect measuring system (HL5500PC, Accent optical Technology, USA). The optical absorption spectra of films in the ultraviolet-visibleinfrared( UV-Vis-IR) region were recorder by the UV spectrophotometer(U-3501, Hitachi, Japan). The resistivity, carrier concentration, and Hall mobility of ZnS deposited on glass substrate as a function of post-annealing.

• 한국건축시공학회지
• /
• 제9권4호
• /
• pp.63-73
• /
• 2009

최근 건설생산현장에서는 경제가 성장함과 동시에 사회적으로 급격하게 증가하는 건축물의 수요를 충족시키기 위해서 표준화, 대량 생산화가 가능한 건식 공법이 각광을 받고 있다. 이러한 현실에 부응하여 에너지 절감효과 및 공사기간 단축, 다양한 형태로 적용이 가능하고 경제성을 가지는 샌드위치 패널이 많이 사용되고 있다. 샌드위치 패널의 형태는 양면 도장 강판 사이에 유기계 및 무기계 단열재를 합성한 복합 자재이다. 유기계 단열재는 PUR(Poly-uretane foam) 및 EPS(Expanded poly-stylene foam) 등이 사용되며, 무기계 단열재는 Glass wool 및 Mineral wool 등이 사용된다. 유기계 단열재는 화재 시 불이 잘 붙어 대피할 수 있는 시간 부족과 유독가스의 발생으로 인명피해가 크게 발생할 수 있지만, 무기계보다 가격이 싸서 유기계 재료를 사용한 샌드위치 패널이 많이 사용되고 있다. 반면, 무기계 단열재 중 경량기포콘크리트는 단열성과 내화성, 경량성 등이 뛰어나기 때문에 샌드위치 패널에 적용하여 유기계의 단점을 해결하기 위한 많은 연구가 수행되어져 왔다. 단열성 및 내화성, 경량성이 뛰어난 경량기포콘크리트는 기포제를 활용하여 시멘트 경화체 내에 다량의 공극을 발생시켜 제조한 것으로서 역학적 특성은 사용되는 기포제와 발포제의 종류에 따라 많은 영향을 받게 된다. 기포제는 계면활성작용에 의해 물리적으로 기포를 도입하는 것으로써 공기량은 최고 85%까지 생성될 수 있으며, 크게 계면활성제계, 가수분해 단백질계로 구분될 수 있다. 계면활성제계 기포제는 수용액 상에서 기포시키면 안정되고, 점성이 높은 기포가 생기지만 시멘트 슬러리와 혼합 시 안정성이 저하되어 서로 연속된 형태의 기포를 형성한다. 가수분해 단백질계 기포제는 계면활성제계 기포제와는 달리 시멘트 슬러리와 혼합 시 안정되고 서로 독립적인 형태의 기포를 형성하게 된다. 발포제는 금속분말이 알칼리 용액과 접촉하여 수소가스를 발생시키는 원리를 이용하는 것으로써 현재 Autoclaved Light-Weight Concrete(ALC)의 제조에 사용되고 있다. 이와 같이 경량기포콘크리트 제조에 사용되는 기포제 및 발포제는 특성이 각기 다르기 때문에 내부 공극이 변화되고 이에 따라 경량기포콘크리트의 물리적, 단열특성이 변화될 것으로 예상된다. 따라서 본 연구에서는 기포제와 발포제를 사용한 경량기포콘크리트를 샌드위치 패널의 내부 단열재로 활용하는 기초적자료를 제공하기 위한 실험적 연구를 수행하였다. 즉, 경량기포콘크리트를 제조하는데 가장 일반적으로 사용하고 있는 기포제 및 발포제를 대상으로 하여 각각의 첨가량에 따른 경량기포콘크리트의 기포구조 및 열적특성을 검토함으로써 경량기포콘크리트의 높은 단열성능을 확보하기 위한 최적조건을 제시하기 위한 실험 실증적 연구를 수행하였다.

• 한국산업보건학회지
• /
• 제4권2호
• /
• pp.157-167
• /
• 1994

This study was conducted to analyze the relationship between the types of fiber and its content and the levels of airborne fiber concentrations at eight parking lots where sprayed insulation material was found on the walls and ceilings. Also this study was designed to find the relationship between the levels of airborne fiber concentrations and such variables as air current, humidity, total exhaust volume, surface condition of insulation material and building age. The results obtained were as follows : 1. No significant correlation was found between the levels of airborne tiber concentration and the building age, air current, humidity, total exhaust volume, space and the number of traffics. 2. A significant correlation was found between the levels of airborne fiber concentration and the MMMF content of the insulation material(r=0.7594). However, no significant correlation was found between the levels of airborne fiber concentration and total fiber content of insulation material. 3. The differences of the airborne fiber concentrations among Cateogory 1, 2 and 3 classified by the degrees of surface insulation material maintenance were very significant. 4. Two bulk samples contained 30% crodicolite and 1% anthophylite. The MMMFs, in all parking lots, included mineral wool, cellulose fiber, trace cellulose fiber, trace tiber glass and vermiculite. 5. The mean value and the range of airborne fiber concentrations at 8 parking lots were $0.0239{\pm}0.0095f/cc$ and 0.0054-0.0447 f/cc, respectively. The fiber concentrations of 35 out of 38 samples(92%) were over 0.01 f/cc which is the Environment Administration's recommended asbestos level for the underground space. This study suggests that most of building insulation materials used in Korea, contain MMMF and sometimes asbestos. Currently, MMMF pollution levels may exceed the Environment Administration's recommended level for underground space. It has been found that airborne fiber concentrations increased significantly with MMMF content and with the maintenance condition of surface material. Therefore, it is recommended that a proper management technique should be developed and immediately implemented since the conditions of surface material will be gradually deteriorated due to building age and usage. Since health hazards of the MMMF, similar to those of asbestos, are being gradually acknowledged, a proper management technique which is applicable to control total airborne fiber concentrations, both asbestos and MMMF, be developed and an acceptable indoor air standard be promulgated as early as possible.

• 한국건축시공학회지
• /
• 제16권5호
• /
• pp.421-428
• /
• 2016

본 연구에서는 전기전도도 시험방법을 이용하여 다양한 산업부산물재료의 포졸란 반응성을 평가할 수 있는 대안을 제안하고자 하였다. 실험에 사용된 재료는 일반적으로 포졸란 재료로 활용되고 있는 산업부산물 플라이애시(class F, C) 2종, 실리카퓸(densified, undensified) 2종, 메타카올린과 포졸란 반응성이 정량적으로 증명되지 않은 산업부산물인 벤토나이트, 그라스울, 세라믹을 활용하여 포졸란 반응성을 측정 하였다. 각 재료가 $40^{\circ}C$ 포화수산화칼슘 수용액에 침지된 이후의 전기전도도의 변화를 관찰하였으며, $450{\sim}500^{\circ}C$에서 관찰된 수산화칼슘의 분해량을 통해 포졸란 반응성을 교차 검증하였다. 28일 압축강도 또한 포졸란 반응에 의한 역학적 성능의 개선여부를 검증하기 위해 활용되었다. 실험결과에 따르면, 전기전도도 최대값과 4시간후의 전기전도도의 차이를 활용하여 포졸란 반응성을 평가하는 것이 적절하다고 나타났다. 이러한 방법을 활용할 경우 수산화칼슘 함유량에 근거한 포졸란 반응성 평가와 매우 유사한 결과를 얻을 수 있었으며, 28일 압축강도 측정을 통해 얻은 결과와도 큰 차이를 보이지 않아, 전기전도도 시험법이 포졸란 반응성이 증명되지 않은 재료의 포졸란 반응성평가에도 충분히 활용될 수 있는 것으로 나타났다.