• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.816-821
• /
• 2013

This case study presents a practical method to reduce resonant vibration of generator-motor set. The generator is driven at 1800rpm by induction integral motor. The vibration is below alarm limits, but the dominant frequency of vibration is sub-synchronous and close to that of bearing fault signal in spite of new bearings. To find an mechanism of abnormal vibration, ODS and Modal analysis is carried out. The measured modal characteristics were compared with those of FE Analysis. The ODS mode at rated speed is consistent with system natural frequency mode that is excited by bearings. To reduce vibration level, the isolation mount at system base is changed with new rubber mount for lower natural frequency.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.3
• /
• pp.101-109
• /
• 2002

It is a very difficult to control the S/G(Steam Generator) levels for not only automatic operation mode but also manual operation made by operators in case of start up or low power plants. The object of this study is to develop and applicate a DCS(Digital Control System) that process the reliable control algorithm in order to control S/G levels automatically from a start-up to full power operation mode for nuclear power plants.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.3
• /
• pp.313-319
• /
• 2002

Since the oil crisis in 1970, a great deal of effort has been made to develop automatic electric load sharing systems as a part of the efforts to save energy. A large scale electric generating system composes more than two generators whose characteristics may be different. When such a system is operated individually or in parallel, the lagrange multiplier's method has difficulty in achieving optimal load distribution because generators usually have the limitations of the operating range with inequality constraints. Therefore, a suitable operating mode of generators has to be decided according to the selection of the generators to meet electric power requirements at the minimum cost. In this study, a method which solves the optimal electric load distribution problem using the dynamic programming technique is proposed. This study also shows that the dynamic programming method has an advantage in dealing with the optimal load distribution problem under the limitations of the operating range with inequality constraints including generator operation mode. In this study, generator operating cost curve of second order equation by shop trial test results of diesel generators are used. The results indicate that the proposed method can be applied to the ship's electric generating system.

• Journal of Power Electronics
• /
• v.15 no.5
• /
• pp.1358-1366
• /
• 2015

This study focuses on an advanced second-order sliding mode control strategy for a variable speed wind turbine based on a permanent magnet synchronous generator to maximize wind power extraction while simultaneously reducing the mechanical stress effect. The control design based on a modified version of the super-twisting algorithm with variable gains can be applied to the cascaded system scheme comprising the current control loop and speed control loop. The proposed control inheriting the well-known robustness of the sliding technique successfully deals with the problems of essential nonlinearity of wind turbine systems, the effects of disturbance regarding variation on the parameters, and the random nature of wind speed. In addition, the advantages of the adaptive gains and the smoothness of the control action strongly reduce the chatter signals of wind turbine systems. Finally, with comparison with the traditional super-twisting algorithm, the performance of the system is verified through simulation results under wind speed turbulence and parameter variations.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.588-592
• /
• 2002

There was the transient vibration on $H_2$ piping system for cooling the generator in a power plant. We found it was resulted from resonance between the natural vibration of the piping system and exciting force from the turbine rotor by measurement and simulation test. We verified it would be changed the mode shape of the piping system by several simulation test for the structural modification of the piping system. Therefore we concluded that the change of natural vibration mode depends on deeply changing effective length of pipe and reducing supports.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1058-1059
• /
• 2015

This paper describes a low-voltage ride-through method for the permanent magnet synchronous generator (PMSG) wind turbine system at a grid fault. The generator side converter regulates the DC link voltage instead of the grid side converter by storing the surplus active power in the rotor inertia during grid fault by the sliding mode controller. The grid side converter controls the grid active power keeping a maximum power point tracking. Simulation results for small scale PMSG wind turbine verify the efficiency of the control method.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1993.06a
• /
• pp.865-868
• /
• 1993

This paper describes a simple random signal generator employing by CMOS analog technology in current mode. The system is a nonlinear dynamical system described by a difference equation, such as x(t＋1) = f(x(t)) , t = 0,1,2, ... , where f($.$) is a nonlinear function of x(f). The tent map is used as a nonlinear function to produce the random signals with the uniform distribution. The prototype is implemented by using transistor array devices fabricated in a mass product line. It can be easily realized on a chip. Uniform randomness of the signal is examined by the serial correlation test and the $\chi$2 test.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.6_3
• /
• pp.1341-1347
• /
• 2023

This study proposes to ensure the seismic stability of an existing switchboard for emergency diesel generator by applying mode analysis, static analysis and dynamic analysis. First, a three dimensional model for the swithboard was made with simplification for mode analysis. Next, The mode analysis for the finite element model of the existing switchboard was performed. The 1st natural frequency below 33 Hz, the seismic safety cutoff frequency, was calculated to be 21.943 Hz. Finally, based on the seismic stability theory, the von-Mises equivalent stresses derived by structural analysis and response spectrum analysis under the normal and faulted conditions were 74.179 MPa and 49.769 MPa, respectively. These are less than specified allowable stresses. So seismic stability was confirmed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.239-239
• /
• 2010

This paper describes the design and analysis of AlN piezoelectric micro generator. The generator was designed to convert ambient vibration energy to electrical power as a AlN piezoelectric material compatible with integataion process. From the simulation results, the resonance frequency of designed model is about 360 Hz and analyzed the bending mode, displacement and expectation output.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.693-696
• /
• 1999

This paper presents an analysis of the chaotic behavior in the discrete-time chaotic generator fabricated by CMOS technology. An approximated empirical equation is extracted from the measurement data of a nonlinear function block. Then the bifurcation diagram and Lyapunov exponent and time waveforms and frequency responses of the chaotic generator are calculated and simulated. And results of experiments in the chaotic circuit with the $\pm$2.5V power supply and clock rate of 10KHz are shown, and analysed.