• 한국태양에너지학회 논문집
• /
• 제30권1호
• /
• pp.34-41
• /
• 2010

Gas hydrates are solid solutions when water molecules are linked through hydrogen bonding and create host lattice cavities that can enclose many kinds of guest(gas) molecules. There are plenty of methane(gas) hydrate in the earth and distributed widely at offshore and permafrost. Several schemes, to produce methane hydrates, have been studied. In this study, depressurization method has been utilized for the numerical model due to it's simplicity and effectiveness. IMPES method has been used for numerical analysis to get the saturation and velocity profile of each phase and pressure profile, velocity of dissociation front progress and the quantity of produced gas. The values calculated for the sample length of 10m, show that methane hydrates has been dissolved completely in approximately 223 minutes and the velocity of dissociation front progress is 3.95㎝ per minute. The volume ratio of the produced gas in the porous media is found to be about 50%. Analysing the saturation profile and the velocity profile from the numerical results, the permeability of each phase in porous media is considered to be the most important factor in the two phase flow propagation. Consequently, permeability strongly influences the productivity of gas in porous media for methane hydrates.

• 한국생산제조학회지
• /
• 제19권2호
• /
• pp.301-305
• /
• 2010

Cutting procedures where qualities are determined by various demand factors largely influences shipbuilding productivity. Particularly, defects in cutting shapes and cutting surface results in delay for post shipbuilding stages such as in welding and assemblage lines which could become factors for reduced economic viability of the project. Existing cutting procedures utilize fossil fuels such as propane or ethylene as the main fuel component and these methods applied particularly to ship plate cutting gives relatively slow cutting speed and generates large quantities of harmful and sometimes poisonous polluting fumes of which warrants an urgent need to look for alternative cutting methods. Recent introduction of hydrox gas generated by electrically dissociating water into hydrogen and oxygen components to be utilize as an alternative cutting fuel has resulted not just in visible improvement on cutting quality and speed over the existing methods but it has also been welcomed as an environmentally friendly clean fuel source. This paper has been prepared to serve as the basis for accommodating this environmentally friendly hydrox gas cutting method into actual working environment by observing and recording hydrox gas cutting thermal characteristics.

• 한국가스학회지
• /
• 제26권5호
• /
• pp.1-9
• /
• 2022

적합한 인공채유법의 선정은 유정의 효율적인 운영과 경제성의 측면에서 중요하다. 일반적으로 인공채유법의 선정은 유정 설계에 포함되는 과정이며, 저류층의 상황이나 유정의 생산 조건에 따라 두 가지 이상의 인공채유법을 적용한 혼합시스템을 활용하여 오일생산량을 증가시킬 수 있다. 대표적인 인공채유법 중 하나인 전기공저펌프(Electric submersible pump, ESP)는 전기 에너지를 이용한 다단계 원심분리형 펌프를 이용하여 유정 하부에서 압력을 공급하는 방식으로 오일생산량을 증대시킨다. 그러나 이 방식은 펌프의 수명과 연관된 결함에 의해 적용 기간에 한계를 가지는 단점이 있다. 이에 전기공저펌프/가스리프트 혼합시스템(ESP/Gas lift hybrid system)을 적용하여 전기공저펌프의 결함 발생 시에는 바로 가스리프트로 전환하여 오일생산이 중단되는 시간을 감소시킬 수 있다. 본 연구에서는 퍼미안 분지에 있는 육상 수평정을 대상으로 전기공저펌프/가스리프트 혼합시스템을 적용했을 때의 생산 중단시간의 감소에 따른 오일생산량 차이 및 경제성 분석을 수행하였다. 전기공저펌프/가스리프트 혼합시스템은 전기공저펌프의 단독 적용에 비교하여 더욱 효율적인 오일 생산성을 나타냄을 확인하였다. 또한 이 연구에서는 혼합시스템을 적용했을 때 얼마나 경제적 이득이 있는지를 정량적으로 예측함을 나타냈다.

• Journal of Welding and Joining
• /
• 제26권4호
• /
• pp.44-49
• /
• 2008

Generally, wear plate is steel plate having improved surface contact strength and impact strength by surface hardening which is welded using materials with good corrosion resistance, wear resistance and thermal resistance property. CFP GMAW(Compound Filler Plate Gas Metal Arc Welding) is the cladding method using GMAW with the CFP, which is bound with waterglass, on the substrate. It has advantages of reducing compound powder loss, uniform penetration, and preventing hardness decrease. To develope mass production technique of CFP GMAW process for production of high quality wear plate, the method for controling shallow penetration and increasing productivity is required. In this study, twin torch method applied to CFP GMAW process for increasing productivity. And the method was developed by controling penetration control, CFP dry time, gas formation flux and water glass concentration. As a result, applying twin torch method to CFP GMAW process was possible and high quality wide bead could be made without overlap joint.

• 한국산학기술학회논문지
• /
• 제14권9호
• /
• pp.4111-4116
• /
• 2013

프로그레시브 금형은 다수의 공정을 순차적으로 이송시키면서 연속적으로 생산하는 능률적이고 품질이 우수한 가공법이다. 본 연구에서는 가스보일러 연소 배기관의 배기 효율과 불완전 연소의 원인이 되는 배기관을 용접할 때 발생하는 위치 정밀도를 확보하고, 생산성 증가를 목적으로, 제품 형상에 버링을 추가하여 프로그레시브금형을 제작하고, 금형을 분해하지 않고 버링펀치를 교환할 수 있도록 하며, 프로그레시브 금형에 의한 위치 정밀도와 생산성을 향상할 수 있도록 하였다.

• 대한기계학회논문집
• /
• 제18권5호
• /
• pp.1227-1234
• /
• 1994

A cold spot temperature control system for the batch annealing furnace has been established in order to reduce energy consumption which is essential to improve productivity and stabilize the properties of products. A relationship between annealing cycle time and gas flow rate is developed and also for the variation of coil cold spot temperature with time during heating, and actual temperature measurements at mid-width of each coil during soaking. The results of the temperature variation effect on the cold rolled steel sheet batch annealing are as follows. (1) Cooling rate increasing gradually with increasing atmospheric gas flow, but heating rate is hardly increasing without atmospheric gas component change. (2) In case of short time heating, the slowest heating part is the center of B coil and in case of ling time heating, the low temperature point moves from the center of coil to inside coil. (3) The outside of top coil is the highest temperature point under heating, which becomes the lowest temperature point under cooling. (4) Soaking time determination depends on the input coil width, and soaking time for quality homogenization of 1214 mm width coil must be 2 hours longer than that of 914 mm width coil.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2008년도 특별논문집
• /
• pp.126-132
• /
• 2008

Cutting procedures whose qualifies are determined by various variables largely influences shipbuilding productivity. Particularly, defects in cutting shapes and cutting surface results in delay of the post shipbuilding stages such as welding and assemblage process. Because cutting procedures are influenced by various numbers of requirements according to the plate thickness, cutting precision can be maintained when the cutting conditions are appropriate. Existing cutting procedures utilize fossil fuels such as propane or ethylene as the main fuel component. Especially, when fossil fuel is applied to thick plate cutting, this process gives relatively slow cutting speed and generates large quantities of harmful polluting fumes. Recently, hydrogen-oxygen mixed gas generated by electrically dissociating water into Hydrogen and oxygen components is welcomed as an alternative fuel source. Also recent results report that alternative cutting fuel improves the cutting Dualities and speed. This paper presents that cutting characteristics and optimum cutting condition of hydrogen-oxygen mixed gas.

• 한국가스학회지
• /
• 제6권1호
• /
• pp.59-65
• /
• 2002

본 연구는 가스 산업체에서 안전관리, 건설공정, 운영관리 등을 통합할 수 있는 새로운 정보화 모델, 즉 PIIS 모델을 제안하고자 한다. 여기서 개발된 PIIS 모델을 기반으로 가스설비를 통합관리 한다면 안전 및 위험관리를 극대화 할 수 있고, 동시에 생산성과 원가절감 효과를 증대시킬 수 있는 장점이 있다. 따라서 PIIS 시스템의 도입은 동기화와 통합화를 안정적으로 가져갈 수 있다는 측면에서 가스 공급자와 소비자 상호간에 이윤을 공유하게 된다. 결과, PIIS 운영체계는 인수기지의 건설단계에서 도입하는 것이 보다 효과적이지만. 천연가스의 탐사 단계부터 최종 소비자에게 공급되는 전체 라인에 적용하는 것이 가스업체의 생산성, 안전성, 경제성에 분명한 이익을 제공할 것이다.

• 한국생산제조학회지
• /
• 제21권2호
• /
• pp.349-353
• /
• 2012

As the world wind energy market grows rapidly, the productions of wind power generation equipment have recently increased, but manufacturers are not able meet this requirement. Particularly offshore wind energy industry is one of the most popular renewable energy sectors. To generalize welding processes, the welding automation is considered for steel structure manufacturing in offshore wind energy to get high quality and productivity. Welding technology in construction of the wind towers is depended on progress productivity. In addition, the life of wind tower structures should be considered by taking account of the natural weathering and the load it endures. The root passes are typically deposited using Gas Tungsten Arc Welding(GTAW) with a specialized backing gas shield. Not only the validation consists of welders experienced in determining the welding productivity of the baseline welding procedure, but also the standard testing required by the ASME section IX and API1104 codes, toughness testing was performed on the completed field welds. This paper presents the welding characteristics of the root-pass welding of high tensile steel in manufacturing of offshore wind tower. Based on the result from welding experiments, optimal welding conditions were selected after analyzing correlation between welding parameters(peak current, background current and wire feed rate) and back-bead geometry such as back-bead width(mm) and back-bead height performing root-pass welding experiment under various conditions. Furthermore, a response surface approach has been applied to provide an algorithm to predict an optimal welding quality.

• Asian-Australasian Journal of Animal Sciences
• /
• 제13권8호
• /
• pp.1113-1120
• /
• 2000

Productivity, nutrient contents, in vitro gas production and in sacco degradability of different fractions and whole OPF were determined to assess the feeding value of OPF as a ruminant feed. An in vivo digestibility trial was also carried out using goat. Freshly harvested OPF was randomly collected, partitioned and weighed. An OPF from 21 years older palm weighed 13.4 kg and the annual fresh matter yield of petiole, leaflet and midrib was 46.5, 11.8 and 3.4 ton/ha, respectively. Leaflet contained 439, 926, 698, 501, 168, 196, 748 and 52 (g/kg) of dry matter (DM), organic matter (OM), neutral detergent fiber (NDF), acid detergent fiber (ADF), cellulose (CE), hemicellulose (HC), total carbohydrate (TC) and non fiber carbohydrate (NFC), respectively. Petiole contained lower (p<0.01) DM, CP and EE contents than leaflet. Organic matter, CE and TC contents were higher (p<0.01) in petiole compared to leaflet. Silica and lignin contents were highest (p<0.01) in midrib followed by leaflet, whole OPF and least in petiole. The Ca, P, Na, K and Mg contents (g/100 g DM) of leaflet were 0.529, 0.182, 0.039, 0.876, and 0.168, respectively. In vitro DM digestibility (g/100 g) at 48 h of leaflet, petiole and midrib was 32.7, 38.7 and 30.2, respectively. The in sacco DM degradation (g/100 g) at 48 h of leaflet was higher than that of whole OPF, petiole and midrib. The in vivo digestibility of DM, OM, CP and ADF of whole OPF was 52, 56, 43 and 26%, respectively. It can be concluded that leaflet is the most nutritious fraction of OPF and midrib is the least. The nutrient content and digestibility of the whole OPF showed that OPF could be an alternative roughage source for ruminant diets.