• Journal of the Korean Institute of Gas
• /
• v.9 no.3 s.28
• /
• pp.44-48
• /
• 2005

Experimental works were carried out to evaluate the service life of low pressure LPG regulators for domestic use. Experimental results showed that the operating pressure of regulators used for 7 years notably deviated from the standard value of the adjusting pressure and the lock-up pressure. Thus, it is estimated that low pressure LPG regulators have approximately 6 years of service life.

• Journal of the Korea Institute of Building Construction
• /
• v.8 no.6
• /
• pp.161-166
• /
• 2008

This study is focused on the welding performance of automatic gas pressure welding machine adapted to korean construction site by external appearance investigation. As gas pressure welding is more economical and has good performances compared with other steel bar jointing methods, as arc welding and mechanical joint etc, in Japan, the gas pressure welding is one of the typical connection of steel reinforcement when connecting the D29 and thicker steel bars, But in Korea, gas pressure welding joint method is not widely used caused by the shortage of skilled workers. so to activate the gas pressure welding in Korea, the automatic gas pressure welding machine is developed. In this study, the welding performances of gas pressure welding joint samples using korean automatic gas pressure welding machine are measured by external appearance investigation - blown diameters, blown length, welding face disagreement, central axis eccentric ratio, bending, sag and crack. The results of welding performances on the gas pressure welding joint samples show that samples are satisfied with the standard value regulated in KS D 0244 and JIS Z 3120.

• Journal of the Korea Institute of Building Construction
• /
• v.5 no.3 s.17
• /
• pp.131-138
• /
• 2005

The study is focused on the settling the developing direction of korean gas pressure welding machine which can be applied in korean construction sites with moderate and high performance. Gas pressure welding is more economical and has good performances than other steel bar jointing methods, as arc welding and mechanical joint etc. Therefore in Japan, the gas pressure welding, which has less loss of steel bars and low performance of joints, when connecting the D29 and thicker steel bars, Is one of the typical connection of steel reinforcement. But in Korea, the gas pressure welding method is not widely used caused by the shortage of skilled workers, and this situation in Korea can not be solved in short period. The training of the skilled workers takes long period(around $6\~10$ years), and there is no certification system for gas pressure welding. So to activate the gas pressure welding in Korea, the development of the automatic gas pressure welding machine is necessary, which gives regular performance of the steel bar joints and can be operated by not sufficient skilled workers. The automatic gas pressure welding machine was developed in Japan, but this machine has many problems when applied in korean construction sites. Therefore, it is necessary to develop a korean automatic gas pressure welding machine to overcome this problems. To develop korean automatic gas pressure welding machine, the problems, which shows when applied in korean construction sites, need to be investigated. According to the investigation, counterproposals are presented for the pragmatical development of the korean automatic gas pressure welding machine.

• 연구논문집
• /
• s.34
• /
• pp.11-19
• /
• 2004

An Experimental study on the characteristics of high pressure gas quenching system was carried out in the present study. The characteristics of gas quenching system have been studied with high pressure gas chamber and specimen for various gas pressure and velocity which are the design parameter of quenching system. The quenching gas was used compressed air which properties are very similar with Nitrogen gas usually used in industrial gas quenching system. The result shows that the quenching rate of mid surface of specimen is lower than each ends of them which are close to low temperature quenching surface. And to increases the quenching intensity, the increment of quenching gas pressure is more efficient than the increment of quenching gas velocity at the point of reducing the circulation fan power.

• Journal of the Korean Institute of Gas
• /
• v.27 no.2
• /
• pp.57-64
• /
• 2023

As the meter reading method of gas meters develops, smart gas meters capable of remote meter reading (leak checking meters and multi-function safety meters) are being used. These meters have a function to judge leakage by utilizing the flow rate and pressure data collected as an additional function. Leakage judgment function using flow rate data has valid cases in the actual field, but the pressure data-based leakage judgment standard is based on not only the pressure value change due to leakage but also various factors (pressure regulator pressure, connection with adjacent meters, usage of adjacent houses, location of meters, etc.). There is a problem with pressure magnitude changes (levels). In this paper, as a technique that can judge leaks by using pressure data collected from smart gas meters, it was developed through preprocessing of pressure data, criteria for pressure value ranges related to leaks, leak judgment techniques, and application case verification.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.1
• /
• pp.75-85
• /
• 1996

The gas pressure acting on the rings in internal combustion engine influences the friction, wear and HC emission. In order to understand their characteristics, it is necessary to measure the interring gas pressure during engine operations. In this study, miniature type pressure transducer was developed to measure inter-ring gas pressure. And measurements of cylinder and inter-ring gas pressure were made on a gasoline engine running at full and part load conditions. Finally the characteristics of inter-ring gas pressure variation during engine operation were obtained form analysis of measured date.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.10
• /
• pp.102-109
• /
• 2000

In the present study, gas-assisted molding and structural vibration analysis of hollow long cylinder with the variation of gas injection pressure are performed. Though there are so many parameters such as delay time, injection pressure, and gas pressure on gas-assisted molding, the latter has the most dominant effect on this process. Therefore, the present paper deals with the effects of gas pressure on the dynamic stiffness of the model by means of vibration analysis and then suggests the fundamental materials which can be directly adapted to manufacturing lines.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.3
• /
• pp.15-22
• /
• 1995

This paper presents the effects of assistant gas pressure on laser cutting. To investigate the effects of assistant gas pressure, pressure measuring system was constructed with good handling and precision at low price. The measured results discussed compare with that of laser cutting of STS304. The assistant gas pressure varied with the variation of distance between nozzle and workpiece. The peak pressure existed at some distance and could be known by using the deviced pressure measuring system. The higher assistant gas pressure helps to remove the dross and the exothermic energy out of the material. The quantity of dross beneath the workpiece decreases and the kerf width narrows at measured peak pressure.

• Journal of the Korean Institute of Gas
• /
• v.18 no.6
• /
• pp.40-44
• /
• 2014

In this study, it is analyzed that a change in the shape of small propane containers made of STS304 when increasing of internal pressure. When internal pressure of a small propane container increased, bottom of end plate is convexly changed. This test is applied to a water bath pressure test to analyze the characteristics of the container. Water bath is able to analyze relationship between internal pressure and volume. In result, shape change section is confirmed because bottom of end plate is convexly changed. In addition, this section tend to decrease internal pressure because a volume increment increase out of proportion to pressure. The results of this study are expected to contribute to improving the safety of the pressure vessel, as well as various small propane container.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.11a
• /
• pp.273-275
• /
• 2012

In apartment building with column structure, reinforcing bar of the column is constructed mainly using gas pressure welding job. Therefore, gas pressure welding job in very critical process is construction apartment building with column structure. The purpose of this study is to analyze productivity of gas pressure welding work in column structure apartment using Web-CYCLONE. In this study, a CYCLONE model was developed for the productivity analysis of gas pressure welding work. Through this model, the optimal combination of the resources was obtained. This study will be utilized in the future as a useful tool of productivity analysis and the determination of an optimal combination of resources for gas pressure welding in apartment with column structure.