• Economic and Environmental Geology
• /
• v.54 no.1
• /
• pp.69-76
• /
• 2021

This study is to identify the mineralogical properties of caprock samples from drilling cores of the Pohang basin, which is the research area for the demonstration-scale CO2 storage project in Korea. The interaction of water-rock-gas that can occur due to CO2 injection was identified using geochemical modeling. Results of mineralogical studies, together with petrographic data of caprock and data on the physicochemical parameters of pore water were used for geochemical modeling. Modelling was carried out using the The Geochemist's Workbench 14.0.1 geochemical simulator. Two steps of modeling enabled prediction of immediate changes in the caprocks impacted by the first stage of CO2 injection and the assessment of long-term effects of sequestration. Results of minerlaogical analysis showed that the caprock samples are mainly composed of quartz, K-feldspar, plagioclase and a small amount of pyrite, calcite, kaolinite and montmollonite. After the injection of carbon dioxide, the porosity of the caprock increased due to the dissolution of calcite, and dawsonite and chalcedony were precipitated as a result of the dissolution of albite and k-feldspar. In the second step after the injection was completed, the precipitation of dawsonite and chalcedony occurred as a result of dissolution of calcite and albite, and the pH was increased due to this reaction. Results of these studies are expected to be used as data to quantitatively evaluate the efficiency of mineral trapping capture in long-term storage of carbon dioxide.

• Journal of Environmental Science International
• /
• v.27 no.8
• /
• pp.621-629
• /
• 2018

Many chemically active species such as ${\cdot}H$, ${\cdot}OH$, $O_3$, $H_2O_2$, hydrated $e^-$, as well as ultraviolet rays, are produced by Dielectric Barrier Discharge (DBD) plasma in water and are widely use to remove non-biodegradable materials and deactivate microorganisms. As the plasma gas containing chemically active species that is generated from the plasma reaction has a short lifetime and low solubility in water, increasing the dissolution rate of this gas is an important challenge. To this end, the plasma gas and water within reactor were mixed using the air-automizing nozzle, and then, water-gas mixture was injected into water. The dissolving effect of plasma gas was indirectly confirmed by measuring the RNO (N-Dimethyl-4-nitrosoaniline, indicator of the formation of OH radical) solution. The plasma system consisted of an oxygen generator, a high-voltage power supply, a plasma generator and a liquid-gas mixing reactor. Experiments were conducted to examine the effects of location of air-automizing nozzle, flow rate of plasma gas, water circulation rate, and high-voltage on RNO degradation. The experimental results showed that the RNO removal efficiency of the air-automizing nozzle is 29.8% higher than the conventional diffuser. The nozzle position from water surface was not considered to be a major factor in the design and operation of the plasma reactor. The plasma gas flow rate and water circulation rate with the highest RNO removal rate were 3.5 L/min and 1.5 L/min, respectively. The ratio of the plasma gas flow rate to the water circulation rate for obtaining an RNO removal rate of over 95% was 1.67 ~ 4.00.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.76.1-76.1
• /
• 2010

Recently, many efforts to solve the durability problem of PEM fuel cell are carried on constantly. However, despite this attention, durability researches of gas diffusion layer (GDL) are not much reported yet. Generally, GDL of PEM fuel cell experiences three external attacks, which are dissolution of water, erosion of gas flow, corrosion of electric potential. In this study, among these degradation factors, carbon corrosion of electric potential was focused and investigated with accelerated carbon corrosion test. Through the test, it is confirmed that carbon corrosion occurred at GDL, and corroded GDL decreased a performance of operating fuel cell. The property changes of GDL were measured with various methods such as air permeability meter, pore distribution analyzer, thermo gravimetric analyzer, and tensile stress test to discover the effects of carbon corrosion. Carbon corrosion caused not only loss of weight and thickness, but also degradation of mechanical strength of GDL. In addition, to analysis the reason of GDL property changes, a surface and a cross section of GDL were observed with scanning electron microscope. After 100 hours test, the GDL showed serious damage in center of layer.

• Economic and Environmental Geology
• /
• v.45 no.2
• /
• pp.89-104
• /
• 2012

The solubility of aluminum for two Andisol profiles formed on pyroclastic materials and basaltic rocks from Jeju Island, Korea was investigated. It is found that high organic carbon content and $Al_{pyrophosphate}/Al_{oxalate}$ ratios in the A horizons, suggesting the substantial amounts of reactive Al are associated with organic matter, whereas the low organic carbon content and the $Al_{pyrophosphate}/Al_{oxalate}$ ratios in the Bo horizons indicate that a major part of the reactive Al should be bound inorganically. The differential FT-IR spectra following acid-oxalate dissolution and heating up to 150 and $350^{\circ}C$, and transmission electron microscope (TEM) observation confirm that imogolite is in the Bo horizon. Our results of equilibration experiments demonstrate that the Al solubility in the Bo horizon for Andisols can be clarified by the congruent dissolution model for imogolite-type material (ITM), rather than by the simultaneous equilibrium with both ITM and Al hydroxy-interlayered aluminosilicate. With results from dialysis and aging procedures, it is noted that the formation of a proto imogolite sol showing its transformation to imogolite, which supports the congruent dissolution of ITM primarily controlling the Al solubility of Andisols in Jeju Island, Korea.

• Journal of the Korean Ceramic Society
• /
• v.39 no.7
• /
• pp.635-641
• /
• 2002

Electrical conduction of $SrZrO_3$ doped with $Y_2O_3$ was measured as a function of gas atmosphere and temperature by impedance spectroscopy. Hydrogen dissolution, due to an enhanced driving force in the presence of oxygen, results in protonation by water incorporation. Proton conductivity increased with water vapor pressure, ${P_w}^{1/2}$. In the pure hydrogen atmosphere, the dissolution of hydrogen,$H_2(g)=2H_{i}$ +2e', is supposed to be driven by a reduced activity of electrons, ascribable to their trapping in oxygen vacancies. The activation energy of electrical conductivity was 50 kJ/mol, in wet argon atmosphere in the temperature range of $600~900^{\circ}C$, similar to those reported for proton conduction in the literature. Grain boundary effect in proton conduction was substantial in the 10% doped case at temperatures lower than $700^{\circ}C$.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.12
• /
• pp.31-38
• /
• 1991

The current-voltage characteristics at annealed Be-Cu alloy(1.8-2 wt% Be, 0.2 wt% Co+Ni) interfaces have been studied by means of the cyclic voltammetric method. The specimens were annealed in nitrogen gas($N_{2}$) furnace at 36$0^{\circ}C$ for 1.5 hours. After annealing, the vickers hardness(HV) was increased from 210 to 385. The used solutions were distilled water(H$_{2}$O), 10$^{-3}M\;CsNO_{2},10^{-2}M\;KCl,10^{-2}M\;KOH,10^{-4}M\;H_{2}SO_{4}$ aqueous electrolytes, and ethylalcohol ($C_{2}H_{5}OH$), etc. The cyclic voltammograms showed significant current-voltage characteristics between the annealed and unannealed specimens at the same conditions. The age hardening and the related surface potential barrer and dissolution effects have been observed during the whole experimental process. The dissolution process of annealed Be-Cu alloys was effectively retarded by the age hardening phenomenon. The age hardening effect also raised the surface potential barrier of Be-Cu alloys. The interfacial phenomena of Be-Cu alloys seem to be one of good models for understanding the activation process.

• Korean Journal of Materials Research
• /
• v.24 no.2
• /
• pp.81-86
• /
• 2014

The nitrogen solubility and nitride capacity of $CaO-SiO_2-Al_2O_3-MgO-CaF_2$ slag systems were measured by using gas-liquid equilibration at 1773K. The nitrogen solubility of this slag system decreased with increasing CO partial pressure, with the linear relationship between nitrogen contents and oxygen partial pressure being -3/4. This system was expected to show two types of nitride solution behavior. First, the nitrogen solubility decreased to a minimum value and then increased with the increase of CaO contents. These mechanisms were explained by considering that nitrogen can dissolve into slags as "free nitride" at high basicities and as "incorporated nitride" within the network at low basicities. Also, the basicity of slag and nitride capacity were explained by using optical basicity. The nitrogen contents exhibited temperature dependence, showing an increase in nitrogen contents with increasing temperature.

• Membrane Journal
• /
• v.17 no.4
• /
• pp.352-358
• /
• 2007

A nonporous hollow fiber membrane contactor was used to control the concentration of oxygen dissolved in an aqueous solution, which was predicted along the hollow fiber membrane using a computer simulation. The governing ordinary differential equations were derived for the occurrent flows of the feed aqueous solution and the feed gas mixture in a membrane contactor and they were numerically solved using the 5th Runge-Kutta-Verner method with a personal computer, where the program was coded utilizing a software of the Compaq Visual Fortran 6.6. It is found that the concentration of oxygen dissolved in water increases from 30 to 64 ppm as the length of the hollow fiber increases from 0.4 to 1.2 m when the membrane of fibers are equal to be 16,000; the flow rate of the feed gas is kept to be 0.536 mol/sec; its pressure is maintained to be 486 kPa; the flow rate of the water is 16.69 mol/sec. As the flow rate of the water increases from 9.26 to 26.85 mol/sec, the concentration of oxygen decreases from 40 to 20 ppm with the constant fiber length of 0.4 m. Finally, it is observed that the concentration of oxygen increases from 33 to 69 ppm as the pressure of the feed gas increases from 298 to 847 kPa.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.1
• /
• pp.143-151
• /
• 2020

Recently, research on self-healing concrete has been actively conducted, and various methods have been attempted for use in the maintenance of structures. However, contrary to the technical development of self-healing concrete, the method for evaluating the performance is insufficient. Although surface observation and permeability experiments are widely used to observe the healing of cracks, microscopic observation of surface may be insufficient to assess the overall performance. Also, permeation experiments should consider the losses caused by the dissolution of self-healed product and viscosity of water. Although a gas diffusion experiment have been proposed to overcome the shortcomings of these two test methods, verification has not been made on specimens with actual healing. Therefore, in this study, gas diffusion experiments were performed on the mortar specimens that had healed, and the adequacy of self-healing evaluation by the gas diffusion experiment was verified.

• Journal of the Korean Society for Heat Treatment
• /
• v.27 no.1
• /
• pp.15-22
• /
• 2014

This study is to investigate the phase changes and cold workability after isothermal transformation at $780^{\circ}C$ by using the high temperature gas nitrided (HTGN) STS 430 ferritic stainless steel specimens. The phase diagram of STS 430 steel obtained by calculation showed that the phase appeared at $1100^{\circ}C$ showed as ${\alpha}+{\gamma}{\rightarrow}{\gamma}{\rightarrow}{\gamma}+Cr_2N{\rightarrow}{\gamma}+Cr_2N+CrN$ with increasing nitrogen concentration. Also, the transformation of ${\gamma}{\rightarrow}Cr_2N$ during heat treatment isothermally at $780^{\circ}C$, nitrogen pearlite with lamellar type was fully formed at the nitrogen permated surface layer for 10 hrs. However, this transformation was not completed for 1 hr, resulting nitrogen pearlite plus martensite. The cold rolled specimen of isothermally transformed at $780^{\circ}C$ for 10 hrs after high temperature gas nitriding decreased the layer thickness of nitrogen pearlite inducing the deformation of hard $Cr_2N$ phase. the dissolution rate of $Cr_2N$ phase increased rapidly with increasing cold rolling ratio. Specimens with the microstructure of nitrogen pearlite (isothermally transformed at $780^{\circ}C$ for 10 hrs) were possible to cold rolling without crack formation. However, the mixed structures of nitrogen pearlite + martensite (isothermally transformed at $780^{\circ}C$ for 1 hr) were impossible to cold deformation without cracking.