• Korean Journal of Agricultural and Forest Meteorology
• /
• v.22 no.3
• /
• pp.144-151
• /
• 2020

Agrivoltaic systems (AVS) is defined as combining farm-grown crops with photovoltaic panels (PV) installed several meters above the ground. Solar radiation (W/㎡), photosynthetic photon flux density (PPFD, µmol/㎡/s), air temperature (℃), vapor pressure (kPa), soil moisture (㎥/㎥), soil temperature (℃), wind direction (˚), and wind speed (m/s) were measured under the AVS in Boseong-gun during winter barley season. Data was collected by 5 minute interval. All data can download at Github site (https://github.com/chojaeil/AVS_Boseung). To gap-filling missing solar radiation data during about two weeks, the conversion coefficient from solar radiation to PPFD was estimated as 0.41. Further, according to the ratio of diffuse radiation to direct radiation, the maximum value among the twenty PPFD sensors under the AVS was related to the PPFD value of filed.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.18 no.1
• /
• pp.43-49
• /
• 2020

An engineered barrier system (EBS) for the geological disposal of high-level radioactive waste (HLW) consists of a disposal canister packed with spent fuel, buffer material, backfill material, and gap-filling material. The buffer material fills the space between the canister and the near-field rock, thus serving to restrain the release of radionuclides and protect the canister from groundwater penetration. Furthermore, as significant amounts of heat energy are released from the canister to the surrounding rock, the thermal conductivity of the buffer plays an important role in maintaining the safety of the entire disposal system. Therefore, given the high levels of heat released from disposal canisters, this study measured the thermal conductivities of compacted bentonite buffers from Gyeongju under temperature variations ranging 25 to 80~90℃. There was a 5~20% increase in thermal conductivity as the temperature increased, and the temperature effect increased as the degree of saturation increased.

• Applied Microscopy
• /
• v.28 no.1
• /
• pp.91-105
• /
• 1998

The present study is undertaken to investigate the hypertrophical changes of the corpus allatum (corpora allata, CA) after the ovariectomy in Blattella germanica. In particular, the ultrastructural aspects of the normal and ovariectomized conditions, and induced factors of the hypertrophic phenomenon are focused. Ultrastructure of the CA from an immediately emergent adult is similar to that of the last larval stage that has stopped secreting juvenile hormone. The CA is composed of undifferentiated cells, exhibiting an electron-lucent matrix, a few mitochondria and less smooth endoplasmic reticulum. The karyoplasm occupy most of the cytoplasm. Electron-dense materials are filled with the intercellular spaces and gap junctions are also found. Almost no ultrastructural changes have been noticed during seven days until the oviposition. However, considerable changes in structure have been detected soon after the oviposition. Mitochondria are increased dramatically in number and cristae, and changed to the filamentous form with a high electron density. In addition, Golgi complexes, microtubules, and polysomes are also increased. After an oviposition, the total volume of the CA are decreased again. The volume of the CA are increased continuously, hypertrophy, after the ovariectomy. Morphological aspects of the CA in an early stage after the removal are similar to the structure of the secondary egg maturation. Large and electron dense globules are observed in the ovariectomized CA cytoplasms and they are present in those cells for a long period of time. Yet such a hypertrophical phenomenon occur only in the specific cells. The hypertrophy are caused by hollowing the part of the CA cells and later filling such site with polysomes. In 42 days after the ovariectomy, the nuclear membranes disappear in the CA cells, thus, exhibiting the prokaryotic-like features. Some results of the current study will contribute to the establishment of the model that explain unusual changes accompanied by certain treatment in insects and/or further in animals.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.119-120
• /
• 2000

Influences of sustain voltage on wall charges and wall voltages are experimentally investigated in surface AC plasma display panels(AC-PDPs), in which electrode gap and width are $80\;{\mu}m$ and $270\;{\mu}m$, respectively. The filling gas is Ne-Xe gas mixture, and total pressures 300 Torr. Also it is found that the more amount of Xe mixing ratio makes the less wall charge and voltage for sustain voltage ranged from 140 V to 222 V. The response time has been delayed by adding a small amount of Xe to Ne in comparison with that without Xe. It is also found that the wall charge and voltage are reduced by adding a small amount of Xe to Ne in comparison with those without Xe.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.8
• /
• pp.1294-1301
• /
• 2001

In order to reduce the time and cost for assembly, automobile speaker grills have been injection molded with door trims or map pockets in one piece recently. However, several defects such as short shots or air traps can easily occur due to the decreased fluidity of the melting polymer according to the excessive heat transfer to the mold. Therefore, it is necessary to optimize the resin feed system and predict possible defects by CAE analysis. However it is not possible to obtain exact analysis results for the speaker grill by using general shell elements since the heat transfer in the thickness direction which is the dominant factor of the filling stage can not be considered. Therefore, there have been several efforts to simulate the injection molding nature of the speaker grill by using shell elements with an effective thickness which is smaller than the actual thickness of the part. Two empirical values have been recommended for the effective thickness in real practice. One is 50∼70% of the thickness of the speaker grill and another is the gap distance between the adjacent holes. In this paper, CAE analyses of a map pocket with a speaker grill were conducted using shell elements with both of these recommended effective thicknesses, and the predicted flow fronts were compared with the findings from injection molding experiments. The commercial code MOLDFLOW was used for injection molding analysis and an 850 ton injection molding machine was used for experiments.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.23 no.2
• /
• pp.401-414
• /
• 1996

The purpose of this study was to compare the marginal leakage of resin liner which was used as a liner to amalgam restoration. Control group composed of no liner group, copalite group and experimental group composed of All-bond 2, Vitrebond, Superbond D-liner applied groups were evaluated. Cl.V preparation with a size of $3{\times}2{\times}1.5mm$ on 70 extracted primary molars were made and applied appropriate liners for each groups. After amalgam filling and polishing, polished specimens underwent temperature changed from $5^{\circ}C\;to\;55^{\circ}C$ a thousand times. After thermocycling, specimens were placed in 2% methylene blue dye solution for 72 hours in an incubator set at $37^{\circ}C$. The teeth were sectioned buccolingually and the degree of dye penetration was observed with a spectroscopy. (${\times}30$) The following results were obtained. 1. Vitrebond, All-bond 2, Superbond D-liner group exhibited a statistically significant lower degree of dye penetration than no liner and copalite group. (Kruskal-Wallis analysis, P<0.05) 2. No liner group and copalite group exhibited a similar degree of dye penetration. (Mann-Whitney analysis, P>0.05) 3. All-bond 2 group exhibited a statistically significant lower degree of dye penetration than Vitrebond group, (Mann-Whitney analysis, P<0.05) Superbond D-liner group also exhibited a lower degree of dye penetration than Vitrebond group but was statistically insignificant. (Mann-Whitney analysis, P>0.05)

• Journal of the Korean BIBLIA Society for library and Information Science
• /
• v.25 no.4
• /
• pp.351-359
• /
• 2014

The field of information science has been documented in several ways during its existence and in some ways has mirrored that of other scientific disciplines during the same period. This article examines variables related to author gender of information science articles in American Documentation (AD) during its entire run, 1950 through 1969. Published by the American Documentation Institute, AD was a primary information science journal of its time, changing its name in 1970 to the Journal of the American Society for Information Science (JASIS), corresponding with the change of the parent organization's name to the American Society for Information Science (1968). AD was preceded by an earlier "information science" publication, the Journal of Documentary Reproduction (JDR), 1938-1942, issued by the American Library Association. Studies indicate that females contributed about 8% for the entire run of articles in JDR (1938-1942) and about 22% for the first twenty-seven years of JASIS (1970-1996). The present study explores the nature of female contributions to AD for the middle period (1950-1969). It has been determined that for the entire run of the journal under the name AD, female authors comprised about 17% of the contributors, which places their publishing percentage for this period between the earlier and later periods, thus expectedly filling the gap.

• Journal of Navigation and Port Research
• /
• v.41 no.6
• /
• pp.381-388
• /
• 2017

Recently, renewed attention for technological applications within the maritime industry has taken place, particularly regarding unmanned vessels. There has been a lot of interest about the number of projects aiming at testing the operational feasibility of unmanned vessels, particularly in relation to technological, safety and security issues. Nevertheless, no studies have investigated this issue from the point of view of seafarers towards unmanned vessels; this paper aims at filling this gap. Data has been collected through a survey questionnaire. A Pearson correlational coefficient has been used to test the correlation between some of the variables. The results show that more than half of the respondents indicated that unmanned vessels do not contribute to an increase in accidents at sea. In addition, seafarers believe unmanned vessels will not be operational in the near future, with most of the respondents indicating a 10-20 year time frame. Thirdly, most of the respondents(both officers and ratings).

• Proceedings of the Korea Water Resources Association Conference
• /
• 2019.05a
• /
• pp.16-16
• /
• 2019

기후변화 시나리오 및 계절예측 자료를 포함한 기후정보를 수자원 분야에 활용하기 위해서는 기후정보의 시 공간적인 상세화(donwscaling)을 필요로 한다. 상세화의 경우 역학적 상세화와 통계학적 상세화로 구분될 수 있으며, 통계학적 상세화를 위해서는 대상 지역의 기후특성을 대표할 수 있는 장기 관측 자료의 확보가 중요하다. 국내의 경우에는 자동기상관측장비(Automatic Weather System, AWS)와 종관기상관측장비(Automatic Synoptic Observation System, ASOS)로 부터 수집된 기상관측자료를 사용할 수 있으나 기후변화 시나리오의 통계적 상세화를 위해서는 30년 이상의 자료 기간을 포함하는 ASOS 자료가 적합하다. 하지만 개발도상국과 같이 기상관측기반이 열악한 지역에서는 잦은 결측 등으로 인하여 품질이 좋은 관측자료의 획득이 어려운 상황이다. 따라서 본 연구에서는 측이 포함된 장기 기상관측 자료로부터 대상 지역의 기후특성을 재현할 수 있도록 기본적인 QC(Quality Control)을 거쳐 결측 자료를 보완할 수 있는 기법 및 R 기반패키지를 개발하여 적용성을 평가하였다. 개발된 기법의 적용성 평가를 위해서 기상청에서 QC를 통해 제공하고 있는 60개 ASOS 지점의 관측자료 중 강수량과 기온 변수를 사용하였다. 최대 50%까지의 현실적인 결측 패턴을 임의로 생성하기 위해 실제 개발도상국 관측자료의 일단위 결측 패턴을 이용하였다. 자료의 QC는 관측일 누락/중복 및 문자형 관측값 등 기본적인 오류 검사, 기온의 경우 물리적 허용 범위에 대한 검사, 최고기온과 최저기온의 비교 및 계측기 오작동에 의한 동일한 값의 반복 등을 포함한 내적 일치성 검사를 우선적으로 수행한다. 이후 결측값에 대해서 인근 기상관측소와의 상관성 분석 결과를 기반으로 결측값을 채우고, 최종적으로는 다양한 위성자료 및 재분석 자료 중에서 일단위 기후특성의 재현성 평가를 통해 선정된 격자형 자료와의 상관성 분석 결과를 기반으로 결측값을 보정하였다. 기온의 경우는 결측률이 높더라도 월평균 기후특성에 큰 영향을 미치지 않았지만 강수의 경우에는 5% 이상의 결측이 발생하는 경우 월평균 강수량에 영향을 미쳐 지역의 강수량을 과소 추정하는 결과를 보였다. 개발된 QC 기법을 강수 자료에 적용한 결과 월평균 기후특성을 잘 복원하는 결과를 보였지만, 일단위 강우 사상의 재현에 있어서는 미흡한 결과를 보였다.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.2
• /
• pp.47-52
• /
• 2011

Currently, Exterior wall's U-value about building envelope is 0.36 W/$m^2K$(Central Region), but window's one is 2.1 W/$m^2K$ according to air gap of glazing, filling gas, coating and type of windows. The door"s one is 1.6~5.5 W/$m^2{\cdot}K$ depending on material and configuration of door. As such, energy loss per unit of door is considerably larger like windows. The door for the recognition was relatively low because energy loss through the door is relatively small compared to window area. In this paper, thermal performance was analyzed through simulation targeting the door which has thermal break that can improve the insulation performance and doesn't have one. As a results of simulations, case1 was calculated as the average of 1.63 w/m2k and case 2 was calculated as the average of 4.14 w/m2k. The thermal performance of door depends on the type and condition of insulations. As a results of final simulations, Case1 was calculated as 1.06 w/m2k and Case2 was calculated as 1.27 w/m2k. As a results of the experiments, thermal performance of case 1 was measured as 1.28 w/m2k. Error between experiments and simulations is considered problems encountered when creating the samples. The effect of door frame on the overall thermal performance is slight because it's a small proportion of the door frame.