• Korean Journal of Materials Research
• /
• v.11 no.8
• /
• pp.655-660
• /
• 2001

Surface photovoltage spectroscopy was used to study $In_{0.5}(Ga_{1-x}Al_x)_{0.5}P/GaAs$ grown by metalorganic chemical vapor deposition(MOCVD). Energy gap related transition in GaAs and $In_{0.5}(Ga_{1-x}Al_x)_{0.5}P$ were observed. By measuring the frequency dependence of $In_{0.5}(Ga_{1-x}Al_x)_{0.5}P/GaAs$, we observed that SPV line shape does not chance, whereas the amplitude change. This results is due to the difference in the lifetimes of the photocarriers in GaAs and in $In_{0.5}(Ga_{1-x}Al_x)_{0.5}P$. We also have evaluated the parameters that describe the temperature dependences of the band gap.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.11
• /
• pp.848-853
• /
• 2010

We have grown GaN nanowires by the low pressure MOCVD method on Ni deposited oxidized Si surface and have established optimum conditions by observing surface microstructure and its photoluminescence. Optimum growth temperature of $880^{\circ}C$, growth time of 30 min, TMG source flow rate of 10 sccm have resulted in dense nanowires on the surface, however further increase of growth time or TMG flow rate has not increased the length of nanowire but has formed nanocrystals. On the contrary, the increase of ammonia flow has increased the length of nanowires and the coverage of nanowire over the surface. The shape of nanowire is needle-like with a Ni droplet at its tip; the length is tens of micron with more than 40 nm in diameter. Low temperature photoluminescence obtained from the sample at optimum growth condition has revealed several peaks related to exciton decay near band-edge, but does not show any characteristic originated from one dimensional quantum confinement. Strong and broad luminescence at 2.2 eV is observed from dense nanowire samples and this suggests that the broad band is related to e-h recombination at the surface state in a nanowire. The current result is implemented to the nanowire device fabrication by nanowire bridging between micro-patterned neighboring Ni catalysis islands.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2008.11a
• /
• pp.40-40
• /
• 2008

질화갈륨계 발광다이오드는 차세대 반도체 조명용 및 기타 광전소자 등에의 응용 가능성 때문에 주목을 받고 있다. 본 발표에서는 발광다이오드용 In/ITO 전극이 p-형 질화갈륨과 열처리 후 오믹접촉을 이루는 메커니즘을 설명한다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.10a
• /
• pp.151-151
• /
• 2009

ZnO 박막은 큰 밴드 갭 및 가시광 영역에서 높은 광투과성을 가지며, 제조조건에 따라 비저항의 범위가 폭넓게 변화하므로 태양전지, 평판 디스플레이의 투명 전극뿐만 아니라 음향공전기, 바리스터 등에 이용되고 있다. ZnO 박막의 전도성을 향상시키기 위해서 일반적으로 Al, Ga, Ti, In, B, H(n-type), 등과 N, As(p-type)의 도펀트를 사용한다. 본 연구에서는 전기화학적인 방법을 사용하여 ITO/glass위에 ZnO film에 농도에 따른 Ga을 doping 하여 전기전도성 향상과 밴드갭을 넓힘으로서 전자의 recombination을 방지하여 유기태양전지의 효율을 높이는데 목적을 두었다.

• Korean Journal of Materials Research
• /
• v.21 no.5
• /
• pp.268-272
• /
• 2011

Due to their novel properties, GaN based semiconductors and their nanostructures are promising components in a wide range of nanoscale device applications. In this work, the gallium nitride is deposited on c-axis oriented sapphire and porous SWCNT substrates by molecular beam epitaxy using a novel single source precursor of $Me_2Ga(N_3)NH_2C(CH_3)_3$ with ammonia as an additional source of nitrogen. The advantage of using a single molecular precursor is possible deposition at low substrate temperature with good crystal quality. The deposition is carried out in a substrate temperature range of 600-750$^{\circ}C$. The microstructural, structural, and optical properties of the samples were analyzed by scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and photoluminescence. The results show that substrate oriented columnar-like morphology is obtained on the sapphire substrate while sword-like GaN nanorods are obtained on porous SWCNT substrates with rough facets. The crystallinity and surface morphology of the deposited GaN were influenced significantly by deposition temperature and the nature of the substrate used. The growth mechanism of GaN on sapphire as well as porous SWCNT substrates is discussed briefly.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.2
• /
• pp.107-112
• /
• 2005

We present an AlGaN/GaN metal-insulator-semiconductor-heterostructure field effect transistor (MIS-HFET) with an $Al_2O_3-HfO_2$ laminated high-k dielectric, deposited by plasma enhanced atomic layer deposition (PEALD). Based on capacitance-voltage measurements, the dielectric constant of the deposited $Al_2O_3-HfO_2$ laminated layer was estimated to be as high as 15. The fabricated MIS-HFET with a gate length of 102 m exhibited a maximum drain current of 500 mA/mm and maximum tr-ansconductance of 125 mS/mm. The gate leakage current was at least 4 orders of magnitude lower than that of the reference HFET. The pulsed current-voltage curve revealed that the $Al_2O_3-HfO_2$ laminated dielectric effectively passivated the surface of the device.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.97-101
• /
• 1995

GaN films were prepared on Si(111) substrates by hydride vapor phase epitaxy (HVPE) on HCl-NH$_3$-N$_2$gas system. Effects of HCl gas flow rate on the film investigate under deposition conditions of flow time of 10min, 20min, 30min. The deposition rate increased with increasing HCl gas flow rate in the range of 10cc/min to 40cc/min and deposition time. Strung (00.2) oriented GaN film was obtained at a lower HCl flow rate and improved of the surface morphology.

• Proceedings of the IEEK Conference
• /
• 2001.06b
• /
• pp.205-208
• /
• 2001

Schottky barrier diodes are fabricated on a intrinsic GaN(4${\mu}{\textrm}{m}$) epitaxial structure grown by rf plasma molecular beam epitaxy (MBE) on sapphire substrates. First, We make Ohmic electrodes (Ti/Al/Ti/Au) by evaporator. Next, we contact RuO$_2$ by dipping in the solution (RuCl$_3$.HClO$_4$), and then we deposit Ni/Au on the surface of RuO$_2$ by evaporator. We study the electrical characteristics of GaN Schottky barrier diodes made by these methods. Measurements are C-V, I-V, SEM, EDX, and XRD for the characteristics of devices. Thickness of RuO$_2$ layer depends on supplied voltage and dipping time. Device of thinner RuO$_2$ layer have a good Schottky characteristics compare with device of thicker RuO$_2$ layer

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.99-99
• /
• 2008

To grow the large diameter GaN with high structure and optical quality has been obtained by hydride vapor phase epitaxy(HVPE) method. In addition to the nitridation of $Al_2O_3$ substrate, we also developed a "step-growth process" to reduce or to eliminate the bowing of the GaN substrate caused by thermal mismatch during cool down after growth. The as-grown 380um thickness and 75mm diameter GaN layer was separated from the sapphire substrate by laser-induced lift-off process at $600^{\circ}C$. A problem with the free-standing wafer is the typically large bowing of such a wafer, due to the built in the defect concentration near GaN-sapphire interface. A polished G-surface of the GaN substrate were characterized by room temperature Double crystal X-ray diffraction (DCXRD), photoluminescence(PL) measurement, giving rise to the full-width at half maximum(FWHM) of the rocking curve of about 107 arcsec and dislocation density of $6.2\times10^6/cm^2$.

• Journal of the Korean Vacuum Society
• /
• v.14 no.4
• /
• pp.222-228
• /
• 2005

Undoped GaN epitaxial layer was grown on c-plane sapphire substrate by a two-step growth with metalorganic chemical vapor deposition(MOCVD). We have investigated the effects of the variation of final growth temperature on surface morphology, roughness, crystal quality, optical property, and electrical property In a horizontal MOCVD reactor, the film was grown at 300 Tow low-pressure with a fixed nucleation temperature of $500^{\circ}C$, varing the final growth temperature from $850\~1050^{\circ}C$ . The undoped GaN epilayers were characterized by atomic force microscopy, high-resolution x-ray diffractometer, photoluminescence, and Hall effect measurement.