• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.152-153
• /
• 2007

$CuInSe_2$ single crystal thin film was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the hot wall epitaxy (HWE) system. After the as-grown $CuInSe_2$ single crystal thin films was annealed in Cu-, Se-, and In-atmospheres, the origin of point defects of $CuInSe_2$ single crystal thin films has been investigated by the photoluminescence(PL) at 10 K. The native defects of $V_{Cu}$, $V_{Se}$, $Cu_{lnt}$, and $Se_{lnt}$ obtained by PL measurements were classified as a donors or acceptors type. And we concluded that the heat-treatment in the Cu-atmosphere converted $CuInSe_2$ single crystal thin films to an optical n-type. Also, we confirmed that In in $CuInSe_2$/GaAs did not form the native defects because In in $CuInSe_2$ single crystal thin films existed in the form of stable bonds.

• Electronic Materials Letters
• /
• v.14 no.6
• /
• pp.749-754
• /
• 2018

Previous studies have reported on the mechanical robustness and chemical stability of flexible amorphous indium gallium zinc oxide (a-IGZO) thin-film transistors (TFTs) on plastic substrates both in flat and curved states. In this study, we investigate how the polyimide (PI) substrate affects hydrogen concentration in the a-IGZO layer, which subsequently influences the device performance and stability under bias-temperature-stress. Hydrogen increases the carrier concentration in the active layer, but it also electrically deactivates intrinsic defects depending on its concentration. The influence of hydrogen varies between the TFTs fabricated on a glass substrate to those on a PI substrate. Hydrogen concentration is 5% lower in devices on a PI substrate after annealing, which increases the hysteresis characteristics from 0.22 to 0.55 V and also the threshold voltage shift under positive bias temperature stress by 2 ${\times}$ compared to the devices on a glass substrate. Hence, the analysis and control of hydrogen flux is crucial to maintaining good device performance and stability of a-IGZO TFTs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.9-9
• /
• 2009

1 wt % Ga-dope ZnO (ZnO:Ga) thin films with n-type semiconducting behavior were grown on c-sapphire substrates by radio frequency magnetron sputtering at various growth temperatures. The room temperature grown ZnO:Ga film showed the faint preferred orientation behavior along the c-axis with small domain size and high density of stacking faults, despite limited surface diffusion of the deposited atoms. The increase in the growth temperature in the range between $300\sim550^{\circ}C$ led to the granular shape of epitaxial ZnO:Ga films due to not enough thermal energy and large lattice mismatch. The growth temperature above $550^{\circ}C$ induced the quite flat surface and the simultaneous improvement of electrical carrier concentration and carrier mobility, $6.3\;\times\;10^{18}/cm^3$ and $27\;cm^2/Vs$, respectively. In addition, the increase in the grain size and the decrease in the dislocation density were observed in the high temperature grown films. The low-temperature photoluminescence of the ZnO:Ga films grown below $450^{\circ}C$ showed the redshift of deep-level emission, which was due to the transition from $Zn_j$ to $O_i$ level.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.770-775
• /
• 2001

Numerical calculation has been performed to investigate the fluid flow, heat transfer and local mass fraction of chemical species in the MOCVD (metalorganic chemical vapor deposition) manufacturing process. The mixing of reactants (trimethylgallium with hydrogen gas and ammonia) was presented by the concentration of each reactants to predict the uniformity of film growth. Effects of inlet size, location, mass flow rate and susceptor/cold wall tilt angle on the concentration were reported. The newly developed reactor, that precursors were supplied at separated inlet to prevent from premixing, was investigated to obtain the quantitative verification. As a results, the optimum mass flow rate, wall tilt angle and inlet conditions were proposed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.211.1-211.1
• /
• 2015

최근 용액 공정을 이용한 산화물 반도체에 대한 연구가 활발히 진행되고 있다. 넓은 밴드갭을 가지고 있는 산화물 반도체는 높은 투과율을 가지고 있어 투명 디스플레이에 적용이 가능하다. 기존의 박막 진공증착 방법은 진공상태를 유지하기 위한 장비의 가격이 비싸며, 대면적의 어려움, 높은 생산단가 등으로 생산율이 높지 않다. 하지만 용액 공정을 이용하면 대기압에서 증착이 가능하고 대면적화가 가능하다. 그리고 각각의 조성비를 조절하는 것이 가능하다. 이러한 장점에도 불구하고, 소자의 신뢰성이나 저온공정은 중요한 이슈이다. Instability는 threshold voltage (Vth)의 shift 및 on/off switching의 신뢰성과 관련된 parameter이다. 용액은 소자의 전기적 특성을 열화 시키는 수분 과 탄소계열의 불순물을 다량 포함 하고 있어 고품질의 박막을 형성하기 위해서는 고온의 열처리가 필요하다. 기존의 열처리는 고온에서 장시간 이루어지기 때문에 유리나 플라스틱, 종이 기판의 소자에서는 불가능하지만 $100^{\circ}C$ 이하의 저온 공정인 microwave를 이용하면 유리, 플라스틱, 종이 기판에서도 적용이 가능하다. 본 연구에서는 산화물 반도체 중에서 InGaZnO (IGZO)를 용액 공정으로 제작한 juctionless thin-film transistor를 제작하여 기존의 열처리를 이용하여 처리한 소자와 microwave를 이용해서 열처리한 소자의 전기적 특성을 한 달 동안 관찰 하였다. 또한 In:Zn의 비율을 고정한 후 Ga의 비율을 달리하여 특성을 비교하였다. 먼저 p-type bulk silicon 위에 SiO2 산화막이 100 nm 증착된 기판에 RCA 클리닝을 진행 하였고, solution InGaZnO 용액을 spin coating 방식으로 증착하였다. Coating 후에, solvent와 수분을 제거하기 위해서 $180^{\circ}C$에서 10분 동안 baking공정을 하였다. 이후 furnace열처리와 microwave열처리를 비교하기 위해 post-deposition-annealing (PDA)으로 furnace N2 분위기에서 $600^{\circ}C$에서 30분, microwave를 1800 W로 2분 동안 각각의 샘플에 진행하였다. 또한, HP 4156B semiconductor parameter analyzer를 이용하여 제작된 TFT의 transfer curve를 측정하였다. 그 결과, microwave 열처리한 소자의 경우 기존의 furnace 열처리 소자와 비교하여 높은 mobility, 낮은 hysteresis 값을 나타내었으며, 1달간 소자의 특성을 관찰하였을 때 microwave 열처리한 소자의 경우 전기적 특성이 거의 변하지 않는 것을 확인하였다. 따라서 향후 용액공정, 저온공정을 요구하는 소자 공정에 있어 열처리방법으로 microwave를 이용한 활용이 기대된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.211-212
• /
• 2010

GaN 기반의 상부발광형 LED는 동작되는 동안 생기는 전기적 단락, 그리고 칩 위의 p-형 전극과 n-형 전극 사이에 생기는 누설전류 및 신뢰성 확보를 위하여 칩 표면에 passivation 층을 형성하게 된다. SiO2, Si3N4와 같은 passivation layers는 일반적으로 PECVD (Plasma Enhanced Chemical Vapor Deposition)공정을 이용한다, 하지만 이는 공정 특성상 plasma로 인한 damage가 유발되기 때문에 표면 누설 전류가 증가 한다. 이로 인해 forward voltage와 reverse leakage current의 특성이 저하된다. 본 실험에서는 원자층 단위의 박막 증착으로 인해 PECVD보다 단차 피복성이 매우 우수한 PEALD(Plasma Enhanced Atomic Layer Deposition)공정을 이용하여 Al2O3 passivation layer를 증착한 후, 표면 누설전류와 빛의 출력 특성에 대해서 조사해 보았다. PSS (patterned sapphire substrate) 위에 성장된 LED 에피구조를 사용하였고, TCP(Trancformer Copled Plasma)장비를 사용하여 에칭 공정을 진행하였다. 이때 투명전극을 증착하기 위해 e-beam evaporator를 사용하여 Ni/Au를 각각 $50\;{\AA}$씩 증착한 후 오믹 특성을 향상시키기 위하여 $500^{\circ}C$에서 열처리를 해주었다. 그리고 Ti/Au($300/4000{\AA}$) 메탈을 사용하여 p-전극과 n-전극을 형성하였다. Passivation을 하지 않은 경우에는 reverse leakage current가 -5V 에서 $-1.9{\times}10-8$ A 로 측정되었고, SiO2와 Si3N4을 passivation으로 이용한 경우에는 각각 $8.7{\times}10-9$과 $-2.2{\times}10-9$로 측정되었다. Fig. 1 에서 보면 알 수 있듯이 5 nm의 Al2O3 film을 passivation layer로 이용할 경우 passivation을 하지 않은 경우를 제외한 다른 passivation 경우보다 reverse leakage current가 약 2 order ($-3.46{\times}10-11$ A) 정도 낮게 측정되었다. 그 이유는 CVD 공정보다 짧은 ALD의 공정시간과 더 낮은 RF Power로 인해 plasma damage를 덜 입게 되어 나타난 것으로 생각된다. Fig. 2 에서는 Al2O3로 passivation을 한 소자의 forward voltage가 SiO2와 Si3N4로 passivation을 한 소자보다 각각 0.07 V와 0.25 V씩 낮아지는 것을 확인할 수 있었다. 또한 Fig. 3 에서는 Al2O3로 passivation을 한 소자의 output power가 SiO2와 Si3N4로 passivation을 한 소자보다 각각 2.7%와 24.6%씩 증가한 것을 볼 수 있다. Output power가 증가된 원인으로는 향상된 forward voltage 및 reverse에서의 leakage 특성과 공기보다 높은 Al2O3의 굴절률이 광출력 효율을 증가시켰기 때문인 것으로 판단된다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.3
• /
• pp.107-112
• /
• 2010

The Cu$(In_{1-x}Ga_x)Se_2$ is the absorber material for thin film solar cell with high absorption coefficient of $1{\times}10^5cm^{-1}$. In the case of CIGS, the movable energy band gap from $CuInSe_2$ (1.00 eV) to $CuGaSe_2$ (1.68 eV) can be acquired while controlling Ga contain ratio. Generally, the co-evaporator method have used for development and fabrication of the CIGS absorption layer. However, this method should need many steps and lengthy deposition time with high temperature. For these reasons, in this paper, a new growth method of CIGS layer was attempted to hydride vapor transport (HVT) method. The CIGS mixed-source material reacted for HCl gas in the source zone was deposited on the substrate after transporting to growth zone. c-plane $Al_2O_3$ and undoped GaN were used as substrates for growth. The characteristics of grown samples were measured from SEM and EDS.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.32 no.2
• /
• pp.45-50
• /
• 2022

Ga₂O₃ thin films were grown on n-type Si substrates at various growth temperatures of 500, 550, 600, 650 and 700℃. The Ga₂O₃ thin films grown at 500℃ and 550℃ were characterized as featureless flat surface. Grown at higher temperatures (600, 650, and 700℃) showed very rough surface morphology. To figure out the annealing effect on the thin films grown at relatively low temperatures (500, 550, 600, 650 and 700℃), the Ga₂O₃ films were thermally treated at 900℃ for 10 minutes. Crystal structure of the Ga₂O₃ films grown at 500 and 550℃ were changed from amorphous to polycrystalline structure with flat surface. Ga₂O₃ film grown at 550℃ was chosen for the fabrication of a Schottky barrier diode (SBD). Electrical properties of the SBDs depend on the thermal treatment were evaluated. A MSM type photodetector was made on the low temperature grown Ga₂O₃ thin film. The photocurrent for the illumination of 266 nm wavelength showed 5.32 times higher than dark current at the operating voltage of 10 V.

• Advances in nano research
• /
• v.2 no.3
• /
• pp.173-177
• /
• 2014

This study is aimed to the numerical modeling of the surface plasmon-polariton excitation by a layer of active (electrically pumped) quantum dots embedded in a semiconductor, covered with a metal. It is shown that this excitation becomes much more efficient if the metal has a form of a thin (with thickness of several nanometers) film. The cause of this enhancement in comparison with a thick covering metal film is the partial surface plasmon-polariton localized at the metal-semiconductor interface penetration into air. In result the real part of the metal+air half-space effective dielectric function becomes closer (in absolute value) to the real part of the semiconductor dielectric function than in the case of a thick covering metal film. This leads to approaching the point of the surface plasmon-polariton resonance (where absolute values of these parts coincide) and, therefore, the enhancement of the surface plasmon-polariton excitation. The calculations were made for a particular example of InAs quantum dot layer embedded in GaAs matrix covered with an Au film. Its results indicate that for the 10 nm Au film the rate of this excitation becomes by 2.5 times, and for the 5 nm Au film - by 6-7 times larger than in the case of a thick (40 nm or more) Au film.

• Solar Energy
• /
• v.20 no.2
• /
• pp.43-54
• /
• 2000

We prepared and characterized $Cu(In_{1-x}Ga_x)Se_2$(CIGS) films using a elemental co-evaporation method for absorbing layer of high efficiency thin film solar cells. The CIGS films deposited on a soda-lime glass exhibited low resistivity because of higher carrier concentration. Na was accumulated at the CIGS surface and the 0 and Se were also accumulated at the surface, suggesting that oxidation is a driving force of Na accumulation. The structure of CIGS film was modified or a secondary phase was formed in the Cu-poor CIGS bulk films probably due to the incorporation of Na into Cu vacancy sites. As the Ga/(In+Ga) ratio increased, the diffraction peaks of $Cu(In_{1-x}Ga_x)Se_2$ films were shifted to larger angle and splitted, and the grain size of $Cu_{0.91}(In_{1-x}Ga_x)Se_2$ films became smaller. All $Cu_{0.91}(In_{1-x}Ga_x)Se_2$ films showed the p-type conductivity regardless of the Ga/(In+Ga) ratio. Ag/n-ZnO/i-ZnO/CdS/$Cu_{0.91}(In_{0.7}Ga_{0.3})Se_2$/Mo solar cells were fabricated. The currently best efficiency in this study was 14.48% for $0.18cm^2$ area ($V_{oc}=581.5mV,\;J_{sc}=34.88mA$, F.F=0.714).