• Korean Journal of Crystallography
• /
• v.12 no.3
• /
• pp.171-176
• /
• 2001

HgCdTe films were grown on the (100). (111), (211) CdZnTe, and (100) GaAs substrates by metal organic chemical vapor epitaxy. We have investigated the surface morphology, electrical properties, crystalline qualities, and composition of HgCdTe with substrates orientation. Three dimensional facet growth was occurred on (111) CdZnTe substrate. The crystalline quality of HgCdTe on (100) CdZnTe was superior to that of HgCdTe on (100) GaAs. FWHM values of double crystal x-ray diffraction of HgCdTe on (100) CdZnTe and (100) GaAs were 55 and 125arcsec, respectively. HgCdTe on GaAs substrate showed n-type conductivity with high mobility, however, HgCdTe on CdZnTe showed p-type conductivity with carrier concentration of higher than 10/sup 16/㎤.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.165-165
• /
• 2010

$1.55\;{\mu}m$ 대역의 레이저 다이오드를 제작하기 위해, InP(001) 기판에 InAlGaAs 물질을 장벽층으로 하는 InAs 양자점 구조를 분자선증착기 (MBE)를 이용하여 성장하고 구조 및 광학적 특성을 Double Crystal X-ray Diffraction (DCXRD), Atomic Force Microscopy (AFM), Photoluminescence (PL)을 이용하여 평가하였다. 일반적으로 InAlGaAs 물질은 고유한 상분리 현상 (Phase Separation)이 나타나는 특성이 있으며, 이는 양자점 성장에 중요한 요인으로 작용할 수 있다. 이러한 InAlGaAs 물질의 상분리 현상을 기판온도 ($540^{\circ}C$, $555^{\circ}C$, $570^{\circ}C$)를 비롯한 성장변수를 변화시켜 제어하고 InAs 양자점 형성에 어떠한 영향을 미치는지를 분석하였다. 540의 성장온도에서 InP(001) 기판에 격자정합한 InAlGaAs 장벽층이 성장온도를 $570^{\circ}C$로 증가시킬 경우 기판에 대하여 인장 응력 (Tensile Strain)을 받는 구조로 변화되었다. 인장응력을 받는 InAlGaAs 장벽층을 Ga Flux 양을 조절하여 격자정합한 InAlGaAs 층을 형성할 수 있었다. AFM을 통한 표면 형상 분석 결과, 서로 다른 기판온도에서 성장한 InAlGaAs 물질이 InP(001) 기판에 격자정합 조건일지라도 표면의 거칠기 (Surface Roughness)는 매우 다른 양상을 보였고 InAs 양자점 형성에 직접적으로 영향을 주었다. $570^{\circ}C$에서 성장한 InAlGaAs 위에 형성한 InAs 양자점의 가로방향 크기를 세로방향 크기로 나눈 비율이 1.03으로서, 555와 $540^{\circ}C$의 1.375 와 1.636와 비교할 때 모양 대칭성이 현저히 개선된 것을 알 수 있다. 상분리 현상이 줄어 표면 거칠기가 좋은 InAlGaAs 위에 양자점을 형성할 때 원자들의 이동도가 상대적으로 높아 InAs 양자점의 크기가 증가하고, 밀도가 감소하는 현상이 나타났다. 또한 InAlGaAs 장벽층이 InP(001) 기판을 기준으로 응력 (Compressive 또는 Tensile)이 존재하는 경우, InAs 양자점 모양이 격자정합 조건 보다 비대칭적으로 변하는 특성을 보여 주었다. 이로부터, 대칭성이 개선된 InAs 양자점 형성에 InAlGaAs 장벽층의 표면 거칠기와 응력이 중요한 변수로 작용함을 확인 할 수 있었다. PL 측정 결과, 발광파장은 $1.61\;{\mu}m$로 InAs 양자구조 형상에 따라 광강도 (Intensity), 반치폭 (Line-width broadening) 등이 변화 되었다.

• Journal of Chest Surgery
• /
• v.42 no.5
• /
• pp.566-575
• /
• 2009

Background: The function of a bioprosthetic heart valve is determined largely by the material properties of the valve cusps. The uniaxial tensile test has been studied extensively. This type of testing, however, does not replicate the natural biaxial loading condition. The objective of the present study was to investigate the regional variability of the biaxial strain versus pressure relationship based on the types of fixation liquid models. Material and Method: Porcine aortic valves and pulmonary valves were assigned to three groups: the untreated fresh group, the fixed with glutaraldehyde (GA) group, and the glutaraldehyde with solvent (e.g., ethanol) group. For each group we measured the radial and circumferential stretch characteristics of the valve as a function of pressure change. Result: Radial direction elasticity of porcine aortic and pulmonary valves were better than circumferential direction elasticity in fresh, GA fixed and GA+solvent fixed groups (p=0.00). Radial and circumferential direction elasticity of pulmonary valves were better than aortic valves in GA fixed, and GA+solvent fixed groups (p=0.00). Radial and circumferential direction elasticity of aortic valves were decreased after GA and GA+solvent fixation(p=0.00), except for circumferential elasticity of GA+solvent fixed valves (p=0.785). The radial (p=0.137) and circumferential (p=0.785) direction of elasticity of aortic valves were not significantly different between GA fixed. and GA+solvent fixed groups. Radial (p=0.910) and circumferential (p=0.718) direction of elasticity of pulmonary valve also showed no significant difference between GA fixed and GA+solvent fixed groups. Conclusion: When fixing porcine valves with GA, adding a solvent does not cause a loss of mechanical properties, but, does not improve elasticity either. Radial direction elasticity of porcine aortic and pulmonary valves was better than circumferential direction elasticity.

• The Korean Journal of Mycology
• /
• v.32 no.1
• /
• pp.16-22
• /
• 2004

The gibberellins (GAs) play important roles in plant growth and development. Twenty three fungi were isolated from the roots of Lindera obtusiloba and Vaccinium koreanum. The numbers of GA-producing fungi were six strains from Lindera obtusiloba and four strains from Vaccinium koreanum. The fungi with GAs-producing activity were incubated for seven days in 40 ml of Czapek's liquid medium at $25^{\circ}C$, 120 rpm, and the amount of each GA in the medium was measured by gas chromatography-mass spectrometer (GC-MS) to determine the productivity of GAs. Penicillium griseofulvum KNU5379 produced more GA in case of $GA_{3}$ than Neurospora crassa known as a GAs-producing fungus. P. griseofulvum KNU5379 was shown to produce $GA_1\;9.79\;ng,\;GA_3\;133.58\;ng,\;GA_4\;2.64\;ng,\;GA_7\;7.80\;ng\;and\;GA_{53}\;0.73\;ng$ in 25 ml of liquid medium. Bioassay using culture fluid of GAs-production fungi was performed on rice sprout.

• Journal of electromagnetic engineering and science
• /
• v.5 no.1
• /
• pp.8-13
• /
• 2005

The InGaP/GaAs hetero-junction bipolar transistor(HBT) monolithic voltage-controlled dielectric resonator oscillator(VCDRO) is first demonstrated for a Ku-band low noise block down-converter(LNB) system. The on-chip voltage control oscillator core employing base-collector(B-C) junction diodes is proposed for simpler frequency tuning and easy fabrication instead of the general off-chip varactor diodes. The fabricated VCDRO achieves a high output power of 6.45 to 5.31 dBm and a wide frequency tuning range of ]65 MHz( 1.53 $\%$) with a low phase noise of below -95dBc/Hz at 100 kHz offset and -115 dBc/Hz at ] MHz offset. A]so, the InGaP/GaAs HBT monolithic DRO with the same topology as the proposed VCDRO is fabricated to verify that the intrinsic low l/f noise of the HBT and the high Q of the DR contribute to the low phase noise performance. The fabricated DRO exhibits an output power of 1.33 dBm, and an extremely low phase noise of -109 dBc/Hz at 100 kHz and -131 dBc/Hz at ] MHz offset from the 10.75 GHz oscillation frequency.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.33-36
• /
• 2004

탄소 도핑$(5{\times}10^{19}\;cm^{-3})$된 p-type GaAsSb 에피층 위에, Ti/Pt/Au, Pd/Au, Pd/Ir/Au를 이용한 다층 오믹 접촉을 제작하였다. MOCVD(metal-organic chemical vapor deposition)를 이용하여 성장시킨 이 p-GaAsSb의 정공 이동도는 탄소의 도핑 농도가 매우 높음에도 불구하고, $50\;cm^2/Vs$로 측정되었다. 오믹 접촉의 전기적 특성을 측정하기 위하여 TLM(Transfer length method)를 이용하였다. Pd/Ir/Au을 이용한 오믹접촉의 specific contact resistivity는 $10^{-8}\;ohm-cm^2$ 보다 작은 수치를, transfer length는 100 nm보다 작은 수치를 보였으며, Ti/Pt/Au을 이용한 ohmic contact의 specific contact resistivity는 $10^{-7|\;ohm-cm^2$ 보다 작은 수치를, transfer length는 400 nm보다 작은 수치를 나타내었다.

• Korean Journal of Optics and Photonics
• /
• v.22 no.1
• /
• pp.35-39
• /
• 2011

The PSPICE equivalent circuit elements of a 1550 nm InGaAsP laser diode were derived by using multi-level rate equations. The device parameters were extracted by using a self-consistent numerical method for the optical gain properties of the MQW active regions. The resulting equivalent circuit model is also applied to an actual optical transmitter, and its PSPICE simulation results show good agreement with the measured results once the parasitic capacitance due to the packaging is taken into account.

• Journal of IKEEE
• /
• v.13 no.4
• /
• pp.23-27
• /
• 2009

Ohmic contact formation and etching processes for the fabrication of MBE (molecular beam epitaxy) grown GaSb-based p-channel HEMT devices on Si substrate have been studied. Firstly, mesa etching process was established for device isolation, based on both HF-based wet etching and ICP-based dry etching. Ohmic contact process for the source and drain formation was also studied based on Ge/Au/Ni/Au metal stack, which resulted in a contact resistance as low as $0.683\;{\Omega}mm$ with RTA at $320^{\circ}C$ for 60s. Finally, for gate formation of HEMT device, gate recess process was studied based on AZ300 developer and citric acid-based wet etching, in which the latter turned out to have high etching selectivity between GaSb and AlGaSb layers that were used as the cap and the barrier of the device, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.196.2-196.2
• /
• 2013

본 연구에서는 분자선 에피택시 (MBE)법으로 성장된 InAs submonolayer quantum dot (SML-QD)을 태양전지에 응용하여 광학 및 전기적 특성을 평가하였다. 본 연구에서 사용된 양자점 태양전지(quantum dot solar cell, QDSC)의 구조는 n+-GaAs 기판 위에 n+-GaAs buffer와 n-GaAs base layer를 차례로 성장 한 후, 활성영역에 InAs/InGaAs SML-QD와 n-GaAs spacer layer를 8주기 형성하였다. 그 위에 p+-GaAs emitter, p+-AlGaAs window layer를 성장하고 ohmic contact을 위하여 p+-GaAs 를 성장하였다. SML-QD 구조의 두께는 0.3 ML 이며, 이때 SML-QD의 적층수를 4 stacks 으로 고정하였다. SML-QD 와의 비교를 위하여 2.0 ML크기의 InAs자발 형성 양자점 태양전지(SK-QDSC)과 GaAs 단일 접합 태양전지 (reference-SC)를 동일한 성장조건에서 제작하였다. PL 측정 결과, 300 K에서 SML-QD의 발광 피크는 SK-QD 보다 고에너지에서 나타나는데(1.349 eV), 이것은 SML-QD가 SK-QD보다 작은 크기를 가지기 때문으로 사료된다. SML-QD는 single peak를 보이는 반면, SK-QD는 dual peaks (1.112 / 1.056 eV)을 확인하였다. SML-QD의 반치폭(full width at half maximum, FWHM)이 SK-QD에 비하여 작은 것으로 보아 SML-QD가 SK-QD보다 양자점 크기 분포의 균일도가 높은 것으로 해석된다. Illumination I-V 측정 결과, SML-QDSC의 개방 전압(VOC) 과 단락전류밀도(JSC)는 SK-QDSC의 값과 비교해 보면, 각각 47 mV와 0.88 mA/cm2만큼 증가하였다. 이는 SK-QD보다 상대적으로 작은 크기를 가진 SML-QD로 인해 VOC가 증가되었으며, SML-QD가 SK-QD 보다 태양광을 흡수할 수 있는 영역이 비교적 적지만, QD내에 존재하는 energy level에서 탈출 할 수 있는 확률이 더 높음으로써 JSC가 증가한 것으로 분석 된다.

• Journal of the Korean Vacuum Society
• /
• v.4 no.S1
• /
• pp.168-173
• /
• 1995

$GaxIn{1_x}As$ epitaxial layers were grown by a simplified hydrode vapor phase epitaxy(VPE) method bsed on the utilization of Ga/In alloy as the source metal. The effects of a wide range of experimental variables(i.e.,inlet mole fraction of HCI, deposition temperature, Ga/In alloy composition) on the ternary composition and growth rate were investigated. Layers of $Ga_{0.47}In_{0.53}As$ lattice matched to InP were successfully grown from alloys containing 5 to 8 at.% Ga. These layers were used to produce state-of-the art p-i-n photodetectors having the following characteristics: dark current, $I_d$(-5V) = 10-20 nA: responsivity, R=0.84-0.86 A/W; dark current, Id(-5V)=10-20 nA; responsivity, R=0.84-0.86 A/W; capacitance, C=0.88-0.92 pF; breakdown voltage, $V_b$ >40V. This study demonstrated for the first time that a simplified hydride VPE process with a Ga/In alloy source is capable of producing device quality epitaxial layers.