• 한국가스학회지
• /
• 제20권4호
• /
• pp.1-6
• /
• 2016

버스와 같은 대형 차량에서 사용되는 대형 CNG 엔진에는 가스 연료 분사를 위한 인젝터가 6개 가량의 단위로 모듈 형태를 구성하고 있다. 이러한 인젝터 모듈은 연료 공급을 위한 입출구가 각각 한 곳으로 구성되어 있으며 쓰로틀 후단을 통하여 흡기관으로 연료를 공급하는 방식이므로 과도 운전에 대한 응답성이 매우 낮은 구조를 형성하고 있다. 본 연구에서는 이러한 인젝터 모듈의 내부 유로에 대한 유동 해석을 통하여 응답성을 개선할 수 있는 방안을 제시하고자 한다. 결론에 따르면 내부 유로의 체적을 감소시킴으로써 가스 연료의 공급 응답성을 개선할 수 있었고, 각각의 인젝터에서 모듈의 출구까지의 거리를 동일하게 하는 방안도 응답성과 연료 공급량의 선형성을 확보할 수 있는 것을 확인하였다. 다만 각 인젝터의 분사 순서 시기에는 큰 영향을 받지 않는 결과를 보였다.

• 대한기계학회논문집B
• /
• 제34권4호
• /
• pp.443-448
• /
• 2010

가스발생기 사이클 액체로켓엔진에서 추진제의 공급압력 변화에 대한 성능 즉, 연소압, 터빈 파워, 엔진 혼합비, 가스발생기 연소가스의 온도 변화를 제시하였다. 로켓엔진의 주요 13개 시스템 레벨 변수를 이용하여 엔진 성능을 수치적으로 계산한다. 산화제 공급압이 증가하면 연소압과 터빈 파워는 증가하며 연료 공급압이 증가하면 연소압과 터빈 파워가 감소한다. 연료 유량 증가에 따라 감소된 가스 발생기의 혼합비는 연소가스 온도를 감소시키며 터빈 구동매질로서의 연소가스 물성을 저하시킨다. 연료 유량 증가에 따라 감소된 터빈 파워는 엔진 추력에 직접 영향을 미치는 주연소기의 연소압을 감소 시킨다.

• 신재생에너지
• /
• 제7권2호
• /
• pp.10-17
• /
• 2011

Korea is the 11th largest energy consumption country and 96% of its total energy consumption depends on imports from overseas. Therefore it is a very important task to secure renewable energy sources which can reduce both the carbon-dioxide emission and dependency on overseas energy imports. Among the various renewable energy sources, organic wastes are important sources. In Korea, 113 million toe of methane is generated from organic wastes annually, but only 3.7% is effectively used for energy conversion. Thus, it is very important to make better use of organic wastes, especially for power generation. The goals of this project are to develope the fuel supplying system of Bio Gasturbine (GT) for 5MW-class co-generation system. The fuel supplying system mainly consists of $H_2S$ removal system, Bio Gas compression system, Siloxane removal system and moisture separating systems. The fuel requirement of 5MW-class GT is at around 60% of $CH_4$, $H_2S$ (<30 ppm), Siloxane(<10 mg/$nm^3$) and supply pressure (> 25 bar) from biogas compressor. Main mechnical charateristics of Bio Gasturbine system have the specific performance; 1) high speed turbine speed (12,840 rpm) 2) very clean emmission NOx (<50 ppm) 3) high efficiency of energy conversion rate. This paper focuses on the development of design technology for food waste biogas pretreatment system for 5MW-class biogas turbine. The study also has the plan to replace the fuel of gas turbine and other distributed power systems. As the increase of bioenergy, this system help to contribute to spread more New & Renewable Energy and the establishment of Renewable Portfolio Standards (RPS) for Korea.

• 한국가스학회지
• /
• 제17권6호
• /
• pp.20-26
• /
• 2013

본 연구에서는 기존 상용 12리터급 경유엔진을 베이스로, 천연가스 연료공급시스템을 추가함으로써 천연가스-경유연료를 동시에 사용하는 혼소엔진을 개발하였다. 전체적인 제어는 기존의 경유엔진 ECU를 이용하고, 추가적인 혼소 ECU를 제작하여 경유와 천연가스 연료가 최적으로 공급되도록 시스템을 구성하였다. 천연가스 연료는 MPI 방식으로 흡기메니홀드에 어뎁터를 이용하여 설치하였다. 혼소엔진의 실험결과, 경유엔진과 동등한 토크와 출력성능을 얻었으며, 배출가스 기준 또한 만족하였다. 전체적인 천연가스 연료 대체율은 70%이고, 주 사용영역에서는 약 76%의 대체율을 보였으며, 이로 인한 연료비용 절감효과는 전체 37% 및 주 사용영역에서는 40%를 얻었다.

• 한국자동차공학회논문집
• /
• 제21권2호
• /
• pp.146-153
• /
• 2013

CNG buses has contributed to improve air quality in cities. But it is difficult to meet the next emission regulations such as EURO-VI without the help of additional post-processing device. Hydorgen has higher flame speed and lower combustion temperature that make it thermal efficiency increase with leaner operation. Using hydrogen natural gas blend (HCNG) fuel is promising technology which can reduce $NO_x$ and $CO_2$ emissions for a natural gas vehicle. However, fuel flow rate of HCNG should be increased since hydrogen's energy density per volume is much smaller than natural gas. In the present study, the characteristics of fuel supply system and its applicability were evaluated in a heavy duty natural gas engine. The results showed that the potential of fuel pressure regulator and fuel metering valve had enough capacity with HCNG. Employed mixer did not affect the distribution characteristics of mixture.

• 한국분무공학회지
• /
• 제8권2호
• /
• pp.7-15
• /
• 2003

The effects of fuel density and fuel viscosity on spray characteristics were investigated under two different gas turbine fuels and various fuel supply pressure conditions through measurement of SMD, number density and volume flux by using PDPA system in dual orifice injector for gas turbine engines. In this study, we found out that the droplet size and spray structure are strongly depend on fuel density for dual orifice injector. The spray characteristics of high density fuel in dual orifice injector are similar with the characteristics of low density fuel in single orifice injector. The shear region between primary main fuel stream and secondary main fuel stream is examined in low density fuel condition but not exist in high density fuel condition, then this shear region is very important in quality of gas turbine spray. There are worth consideration for the effect of fuel density on spray characteristics in frontal device design to improve combustion efficiency.

• 신재생에너지
• /
• 제6권1호
• /
• pp.29-37
• /
• 2010

Biogas is a carbon neutral energy and consists of mostly methane and carbon dioxide, with smaller amounts of water vapor, and trace amounts of $H_2S$, Siloxane and other impurities. Hydrogen sulfide and Siloxane usually must be removed before the gas can be used for generation of electricity or heat. The goals of this project are to develope the Fuel conditioning system of Land Fill Gas for 30kW-Micro Gas Turbine co-generation system. The fuel conditioning system mainly consists of $H_2S$ removal system, Land Fill Gas compressor, Siloxane removal system and many filtering systems. The fuel requirement of 30kW MGT is at least 32% of $CH_4$, $H_2S$ (<30 ppm), Siloxane (<5ppb) and supply pressure (> 0.6 MPa) from LFG compressor. Main mechnical charateristics of Micro Gas Turbine system by using LFG have the specific performance; 1) high speed turbine speed (96,000 rpm) 2) very clean emmission NOx (<9 ppm) 3) high efficiency of energy conversion rate. This paper focuses on the development of design technology for LFG fuel conditioning system. The study also has the plan to replace the fuel of gas turbine and other distributed power systems. As the increase of Land Fill Gas (LFG), this system help to contribute to spread more New & Renewable Energy and the establishment of Renewable Portfolio Standards (RPS) for Korea.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제11권1호
• /
• pp.11-21
• /
• 2019

In product design, the initial design stage is being increasingly emphasized because it significantly influences the successive product development and production stages. However, for larger and more complex products, it is very difficult to accurately predict product reliability in the initial design stage. Various design methodologies have been proposed to resolve this issue, but maintaining reliability while exploring design alternatives is yet to be achieved. Therefore, this paper proposes a methodology for conceptual design considering reliability issues that may arise in the successive detailed design stages. The methodology integrates the independency of axiomatic design and the hierarchical structure of failure mode, effects, and criticality analysis (FMECA), which is a technique widely used to analyze product reliability. We applied the proposed methodology to a liquefied natural gas fuel gas supply system to verify its effectiveness in the reliability improvement of the design process.

• 설비공학논문집
• /
• 제16권11호
• /
• pp.1013-1020
• /
• 2004

The hybrid system of gas turbine and fuel cell is expected to produce electricity more efficiently than conventional methods, especially in small power applications such as distributed generation. The solid oxide fuel cell (SOFC) is currently the most promising fuel cell for the hybrid system. To realize the conceptual advantages resulting from the hybridization of gas turbine and fuel cell, optimized construction of the whole system must be the most important. In this study, parametric design analyses for pressurized GT/SOFC systems have been peformed considering probable practical limiting design factors such as turbine inlet temperature, fuel cell operating temperature, temperature rise in the fuel cell and soon. Analyzed systems include various configurations depending on fuel reforming type and fuel supply method.

• 설비공학논문집
• /
• 제13권12호
• /
• pp.1255-1265
• /
• 2001

A numerical study has been conducted to characterize the transient flow in a utility gas turbine burning natural gas. The solution domain encompasses the supply gas pressure regulator to the combustor of the gas turbine that employs multi-nozzle fuel injectors. Some results produced for verification in the present study agree suite well with the experimental ones. It is found that the total gas flow may decrease noticeably during its combustion mode change, which would be the reason of momentary combustion upset, when a reference case of opening ratios of control valves in the system is applied. Several parameters are then varied in order to make the total gas flow stable over that period of time. Results of this study may be useful to understand the unsteady behavior of combustion system burning natural gas.