• Korean Chemical Engineering Research
• /
• 제44권3호
• /
• pp.314-318
• /
• 2006

본 연구에서는 고분자 전해질 연료전지(PEMFC)의 연료로 새롭게 제안된 개미산을 이용한 직접 개미산 연료전지 시스템에서 우수한 성능을 구현하기 위해서 촉매를 개발하고, EDS와 SEM을 사용하여 촉매의 특성을 분석하였다. 또한, 단일전지 실험을 통하여 기존 상용 촉매와 성능을 비교하였다. 본 연구에서 개발된 Pt-Pd 촉매는 SEM 분석 결과 입자의 크기가 균일하고 조밀한 분포를 나타내었다. 촉매의 종류에 따른 연료전지의 성능실험에서 Pd의 함량 비율이 높을수록 전지의 성능이 우수하였으며, 특히 Pd black은 산화가스로 산소를 사용하였을 경우 상온에서 $130mW/cm^2$ 의 최대전력밀도를 나타냈다. 또한, Pt-Pd 촉매도 우수한 성능을 보였으며, 특히 Pt와 Pd의 비율이 1:1일 때 산화가스로 산소를 사용하였을 경우 상온에서 $120mW/cm^2$의 최대전력밀도를 나타냈다. 시스템의 운전온도를 $60^{\circ}C$까지 증가 시켰을 때, 전지의 성능은 촉매의 반응활성 증가로 크게 증가하였으나, 막의 최고 활성 영역인 $50{\sim}60^{\circ}C$ 범위에서는 운전온도가 전지의 성능에 큰 영향을 미치지 않았다.

• 한국세라믹학회지
• /
• 제44권12호
• /
• pp.720-726
• /
• 2007

Current collectors of SOFC play a significant role on the performance of power generation. In this study a single cell stacked SOFC was assembled using Ag-mesh as a cathode current collector, and evaluated its performance. No gas leakages of the single cell stack occurred in the tests of gas detection and OCV measurement. The OCV and initial power of the stack were 1.09V and $0.45W/cm^2$, respectively, under the flow rates of air at 2,500 cc/min and $H_2$ at 1,000 cc/min at the test temperature of $750^{\circ}C$. A degradation rate of 44.0% was measured during the prolonged time of 307 h. The relatively low durability of the tested single cell stack was found to be the evaporation of Ag-mesh at the current corrector.

• 한국세라믹학회지
• /
• 제47권1호
• /
• pp.75-81
• /
• 2010

The feasibility of using the thin film technology in utilizing lanthanum strontium manganite (LSM) for a solid oxide fuel cell (SOFC) cathode in a low-temperature regime is investigated in this study. Thin film LSM cathodes were fabricated using pulsed laser deposition (PLD) on anode-supported SOFCs with yttria-stabilized zirconia (YSZ) electrolytes. Although cells with a 1 ${\mu}m$-thick LSM cathode showed poor low-temperature cell performance compared to that of a cell with a bulk-processed cathode due to the lack of a triple-phase boundary length, the cell with 200 nm-thick gadolinia-doped ceria (GDC) inserted between the LSM and YSZ showed enhanced performance and more stable operation characteristics in a comparison of a cell without a GDC layer. We postulate that the GDC layer likely improved the cathode adhesion, therefore contributing to the improvement of the cell performance instead of serving as an interfacial reaction buffer.

• 한국수소및신에너지학회논문집
• /
• 제29권5호
• /
• pp.450-457
• /
• 2018

To design the practical core-shell electrocatalysts, combination of core and shell materials is important to meet catalytic activity and durability target. In general, Pd is considered as a good core material due to its best activity caused by strain/ligand effect. Preparing Pd nanoparticles can be a starting point in fabricating core-shell type electrocatalysts, much simplified Pd preparing process is suggested by using carbon monoxide (CO) as a reducing agent and/or capping agent. The solvent composition and reaction temperature can control to nanosheet, tetrahedron, and sphere without using additional stabilizer. Among them, Pd nanosheet which has mainly (111) plane showed about 3 times higher electrocatalytic activity for oxygen reduction reaction (ORR) to the spherical Pd nanoparticles. The enhanced ORR activity of Pd nanosheets can be attributed to the exposure of Pd (111) surface and the high electrochemical surface area. Therefore, we demonstrated that the shape of Pd nanomaterials is easily controlled via a facile reduction method using CO, and (111) plane-oriented Pd nanosheets can be a promising ORR catalysts and core material for polymer electrolyte fuel cells (PEFCs).

• Korean Chemical Engineering Research
• /
• 제50권4호
• /
• pp.749-753
• /
• 2012

본 연구에서는 마이크로 원통형 SOFC 지지체의 특성을 평가하기 위해 직경 3 mm의 연료극 지지체를 제조하여 지지체의 미세구조를 분석하고, 기계적 강도 및 가스투과도를 측정하였다. 다공성 연료극 지지체의 표면과 파단면의 미세구조를 분석하기 위해 SEM (Scanning Electron Microscope)을 이용하였다. 지지체의 가스투과도는 차압계를 이용하여 50, 100, 150 cc/min의 유량에서 측정하였으며, 기계적 강도는 만능 시험기를 이용하여 측정하였다. 마이크로 원통형 연료극 지지체의 기본적인 물성 평가 후 NiO-YSZ, YSZ, YSZ-LSM/LSM/LSCF로 구성된 마이크로 SOFC 단위전지를 제조하였으며, 반응온도와 연료 유량별로 성능평가를 수행하여 $800^{\circ}C$에서 $1095mW/cm^2$의 출력이 얻어짐을 확인하였다. 또한, 반응 온도에 따른 전기화학적 임피던스 특성평가를 통하여 온도가 높아질수록 전해질 이온전도도가 증가되어 ohmic 저항이 감소되고 그에 따라 마이크로 관형 SOFC 셀 성능이 증가함을 확인할 수 있었다.

• 한국태양에너지학회 논문집
• /
• 제34권4호
• /
• pp.17-22
• /
• 2014

The design of a fuel cells stack is important to get optimal output power. This study focuses on the evaluation of fuel cell system for unmaned aerial vehicles (UAVs). Low temperature proton exchange membrane (LTPEM) fuel cells are the most promising energy source for the robot applications because of their unique advantages such as high energy density, cold startup, and quick response during operation. In this paper, a 600 W open cathode LTPEM fuel cell was tested to evaluate the performance and to determine optimal operating conditions. The open cathode design reduces the overall size of the system to meet the requirement for robotic application. The cruise power requirement of 600 W was supported entirely by the fuel cell while the additional power requirements during takeoff was extended using a battery. A peak of power of 900 W is possible for 10 mins with a lithium polymer (LiPo) battery. The system was evaluated under various load cycles as well as start-stop cycles. The system response from no load to full load meets the robot platform requirement. The total weigh of the stack was 2 kg, while the overall system, including the fuel processing system and battery, was 4 kg.

• 한국세라믹학회지
• /
• 제53권5호
• /
• pp.506-510
• /
• 2016

The eutectic melt of BaO-CuO flux is known to be a potential sintering aid for $Ba(Zr,Y)O_3$ (BZY) electrolyte for proton-conducting ceramic fuel cells (PCFCs). A density of BZY higher than 97% of theoretical density can be achieved via sintering at $1300^{\circ}C$ for 2 h using a flux composed of 28 mol% BaO and 72 mol% CuO. In the present study, chemical and structural evolution of BaO-CuO flux throughout the sintering process was investigated. An intermediate holding step at $1100^{\circ}C$ leads to formation of various impurity compounds such as $BaCuO_{1.977}$, $Ba_{0.92}Cu_{1.06}O_{2.28}$ and $Cu_{16}O_{14.15}$, which exhibit significantly larger unit cell volumes than the matrix. The presence of such secondary compounds with large lattice mismatch can potentially lead to mechanical failure. On the other hand, direct heating to the final sintering temperature produced CuO and $Cu_2O$ as secondary phases, whose unit cell volumes are close to that of the matrix. Therefore, the final composition of the flux is strongly affected by the thermal history, and a proper sintering schedule should be used to obtain the desired properties of the final product.

• 마이크로전자및패키징학회지
• /
• 제22권4호
• /
• pp.77-82
• /
• 2015

To increase the performance of solid oxide fuel cell operating at intermediate temperature ($600^{\circ}C{\sim}800^{\circ}C$), $Sm_{0.2}Ce_{0.8}O_2$ (SDC) thin layer was applied to the $La_{0.8}Sr_{0.2}Mn_{0.8}Cu_{0.2}O_3$ (LSMCu) cathode by sol-gel coating method. The SDC was employed as a diffusion barrier layer on the yttria-stabilized zirconia(YSZ) to prevent the interlayer by-product formation of $SrZrO_3$ or $La_2Zr_2O_7$. The by-products were hardly formed at the electrolyte-cathode interlayer resulting to reduce the cathode polarization resistance. Moreover, SDC thin film was coated on the cathode pore wall surface to extend the triple phase boundary (TPB) area.

• 한국수소및신에너지학회논문집
• /
• 제14권1호
• /
• pp.35-45
• /
• 2003

Polymer electrolyte fuel cells(PEFC) have been considered to be a suitable candidate for residential, portable and mobile applications, due to their high efficiency and power density, even at low operating temperature. KIER developed a 5kW class PEFC system for residential application and operated the system for over 1,000 hours. To develop a 5kW PEFC system, performance of a cell was improved through successive tests of single cell of small and large area. Fabrication of three 2,5 kW class stacks, design and fabrication of natural gas reformer, design of auxiliary equipments such as DC/DC converter, DC/AC inverter and humidifying units were carried out along with integration of components, operation and evaluation of total system. During the development period from 1999 to 2001, MEA(membrane electrode assembly) fabrication technologies, design and fabrication technologies for separators, stacking technologies and so on were developed, thereby providing basis for developing stacks of higher efficiency and power density in the future. Experience of development of natural gas reformer opened possibilities to use various kinds of fuels. Main results obtained from the development of a 5kW class PEFC system for residential application are summarized.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 제17회 워크샵 및 추계학술대회
• /
• pp.554-557
• /
• 2005

The bipolar plate is a major component of the PEM fuel cell stack, which takes a large portion of stack cost. In this study, as alternative materials for bipolar plate of PEM fuel cells, graphite composites were fabricated by compression molding. Graphite particles mixed with epoxy resin were used as the main substance to provide electric conductivity. To achieve desired electric properties, specimens made with different mixing ratio, processing pressure and temperature were tested. To increase mechanical strength, one or two layer of woven carbon fabric were added to the original graphite and resin composite. Thus, the composite material is consisted of the three phases: graphite particles, epoxy resin, and carbon fabric. By increasing mixing ratio, fabricated pressure and process temperature, electric conductivity was improved. The results of tensile test showed that the tensile strength of two-phase graphite composite was about 5MPa, and that of three-phase composite was increased to 54MPa.