• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.5
• /
• pp.615-622
• /
• 2020

Frangible bullets, which are shredded after impact on a target, reduce the possibility of both ricochet and unexpected injury in shooting training and in mission acts in dams, nuclear power plants, and cultural properties. Reducing the levels of hazardous materials in shooting ranges, such as lead, has become an important agenda for the government and environmental groups. In this study, the shape of a frangible bullet was designed for efficient shredding, and the safety and reliability were confirmed by actual firing under different process conditions. In addition, the physical characteristics, such as compaction pressure, density, and frangibility of each process, were compared by analyzing the microstructure of the sintered frangible bullet. The experiment revealed the smallest fragmentation after impact on the target under the following conditions: Cu-Sn 85:15; sintering temperature, 600℃; sintering time, one hour. Further development of the process conditions and experimental methods will contribute to the performance and environmental improvement of a frangible bullet.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.8
• /
• pp.452-458
• /
• 2016

The study on pH control at the themophilic solubilization (pretreatment process) was investigated in order to improve the methane gas production of two phase anaerobic digestion of food waste. From a batch experiment, it was observed that the solubilization efficiency was increased from 26.2% to 47.1% and 55.6% by the pH increament from $4.20{\pm}0.40$ (without pH control) to $7.00{\pm}0.50$, and $12.00{\pm}0.50$, respectively. However there was immaterial increase (8.5%) in solubilization efficiency when the pH was increased from $7.00{\pm}0.50$ to $12.00{\pm}0.50$. The two phase anaerobic digestion system was operated for laboratory scale experiment under the solubilization condition of pH $4.20{\pm}0.40$ (Run1) and $7.00{\pm}0.50$ (Run2). Higher soluble chemical oxygen demand (SCOD) and total volatile fatty acid (TVFA) concentration were observed in Run2 throughout the system resulted by the solubilization effect at the pH $7.00{\pm}0.50$. The TVFA concentration in acidogenic reactor was 18.4 g/L which was 1.8 times higher than the result of Run1. Consequently the methane gas production was enhanced to 0.333 L/g VS in the methanogenic reactor, which is 18% higher than the result (0.282 L/g VS) of Run1.

• Journal of Navigation and Port Research
• /
• v.28 no.3
• /
• pp.269-276
• /
• 2004

The reclaimed land has peculiar characteristic of nature environment unlike midtown or inland and also, in comparison with inland, has bad weather condition, such as low temperature, strong wind, excessive sunshine, and moisture involved in a salt. Therefore the case of developing water front needs understanding characteristic of weather environment mused by reclamation in detail and proper development and organized maintenance. If development which doesn't investigate topographic and climate characteristic sufficiently is drove ahead, a rise of expense for energy and maintenance is going to be mused by deteriorating weather environmental, occurring a flaw of facility and calculating inaccurate capacity of facility. We looked into the weather state and drew up the standard weather data of the newport area in Busan which is reclaiming and developing now. In this research at the base qf the standard weather data, we calculate the dynamic peak loads for commerce, business and residence and then we utilize the results of the load calculation as basic information to determine facility capacity in the rear city of the newport area.

• Journal of Environmental Science International
• /
• v.28 no.12
• /
• pp.1061-1069
• /
• 2019

Common reed (Phragmites australis) is widespread in reclaimed land and wetland habitats. Every year, the common reed produces extensive colonies by means of underground rhizomes and ground-surface stolons. From an agricultural point of view, the common reed's large biomass is a good material for supplying organic matter. However, it has not yet been studied in terms of seedling production, transplanting conditions, and decomposition characteristics in reclaimed land. Seeds were harvested from the native common reed in Saemangeum, South Korea, the previous year and stored on an open field. The seeds were sowed in the greenhouse at the beginning of April. Common reed decomposition was studied from June to September, with the use of coarse mesh (5 mm) stem litterbags, on three samping dates and with five replicate packs per sample. These packs were dug in five soil condition (low-salinity topsoil, subsoil, high-salinity topsoil, subsoil, paddy topsoil) to 0.2 m and 0.4 m depth. The highest germination rate of common reed seeds was observed in non-salt solution, but the exhibited germination rate was 70% at 9.38 dS m^-1. The plant height of young reed decreased steadily with increasing salinity, but leaf number did not decrease by 9.38 dS m^-1. The survival rate of the two-year-old reed was 83.3%, which was 35% higher than that of the one-year reed. The transplant success rate was 0% in the no vinyl mulching in the soil, but the first year and second year seedlings survived rates were 63% and 83.3%, respectively, in vinyl mulching. Common reed decomposition rates were faster low salinity than high salinity. All nutrient contents were found to fluctuate significantly with time by soil conditions. We also need to study the growth rate of reed transplanting seedlings by soil moisture contents and the comparison of degradation in common reed tissues.

• Resources Recycling
• /
• v.19 no.6
• /
• pp.51-60
• /
• 2010

A study on the recovery of cobalt and lithium from Lithium Ion Battery(LIB) scraps has been carried out by a physical treatment - leaching - solvent extraction process. The cathode scraps of LIB in production were used as a material of this experiment. The best condition for recovering cobalt from the anode scraps was acquired in each process. The cathode scraps are dissolved in 2M sulfuric acid solution with hydrogen peroxide at $95^{\circ}C$, 700 rpm. The cobalt is concentrated from the leaching solution by means of a solvent extraction circuit with bis(2-ethylhexyl) phosphoric acid(D2EHPA) and PC88A in kerosene, and then cobalt and lithium are recovered as cobalt hydroxide and lithium carbonate by precipitation technology. The purity of cobalt oxide powder was over 99.98% and the average particle size after milling was about 10 lim. The over all recoveries are over 95% for cobalt and lithium. The pilot test of mechanical separation was carried out for the recovery of cobalt from the scraps. The $Co_3O_4$ powder was made by the heat treatment of $Co(OH)_2$ and the average particle size was about 10 ${\mu}m$ after grinding. The recovery was over 99% for cobalt and lithium each other and the purity of cobalt oxide was over 99.98%.

• Economic and Environmental Geology
• /
• v.54 no.5
• /
• pp.505-513
• /
• 2021

Recently, housing prices in metropolitan areas is also increasing in the UK and Australia. Their governments are trying to solve this problem by the housing development in the quarry sites near cities. The cases reviewed in this study, Erith Hill Quarry (The Quarry), Plymstock Quarry, Lilydale Quarry (Kinley), and Bombo Quarry are the mixed-used development cases in the closed quarry sites through the urban planning system. In the UK, the local government uses the urban planning scheme such as the planning permit system, section 106. The local government permits the quarry site development on the condition that it provides necessary public facilities, such as schools and affordable housing for the local community. In Australia, local governments use up-zoning permission rights to convert land uses in quarries from industrial to mixed-use. Development plans have to include urban infrastructure and open space in addition to affordable housings. In the case of Australia, establishing a development plan in advance and filling the quarry pit with overburden through a phased development is expected to have the effect of reducing the project cost. Both countries think that developing brownfields, such as quarry sites, is a more sustainable and eco-friendly development from the perspective of future generations than developing new green fields. Such a perspective of the UK and Australia will be able to give policy implications for our slightly rigid urban development system.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.2
• /
• pp.34-45
• /
• 2016

Global warming and climate change have been caused by combustion of fossil fuels. The greenhouse gases contributed to the rise of temperature between $0.6^{\circ}C$ and $0.9^{\circ}C$ over the past century. Presently, fossil fuels account for about 88% of the commercial energy sources used. In developing countries, fossil fuels are a very attractive energy source because they are available and relatively inexpensive. The environmental problems with fossil fuels have been aggravating stress from already existing factors including acid deposition, urban air pollution, and climate change. In order to control greenhouse gas emissions, particularly CO2, fossil fuels must be replaced by eco-friendly fuels such as biomass. The use of renewable energy sources is becoming increasingly necessary. The biomass resources are the most common form of renewable energy. The conversion of biomass into energy can be achieved in a number of ways. The most common form of converted biomass is pellet fuels as biofuels made from compressed organic matter or biomass. Pellets from lignocellulosic biomass has compared to conventional fuels with a relatively low bulk and energy density and a low degree of homogeneity. Thermal pretreatment technology like torrefaction is applied to improve fuel efficiency of lignocellulosic biomass, i.e., less moisture and oxygen in the product, preferrable grinding properties, storage properties, etc.. During torrefacton, lignocelluosic biomass such as palm kernell shell (PKS) and empty fruit bunch (EFB) was roasted under an oxygen-depleted enviroment at temperature between 200 and $300^{\circ}C$. Low degree of thermal treatment led to the removal of moisture and low molecular volatile matters with low O/C and H/C elemental ratios. The mechanical characteristics of torrefied biomass have also been altered to a brittle and partly hydrophobic materials. Unfortunately, it was much harder to form pellets from torrefied PKS and EFB due to thermal degradation of lignin as a natural binder during torrefaction compared to non-torrefied ones. For easy pelletization of biomass with torrefaction, pellets from PKS and EFB were manufactured before torrefaction, and thereafter they were torrefied at different temperature. Even after torrefaction of pellets from PKS and EFB, their appearance was well preserved with better fuel efficiency than non-torrefied ones. The physical properties of the torrefied pellets largely depended on the torrefaction condition such as reaction time and reaction temperature. Temperature over $250^{\circ}C$ during torrefaction gave a significant impact on the fuel properties of the pellets. In particular, torrefied EFB pellets displayed much faster development of the fuel properties than did torrefied PKS pellets. During torrefaction, extensive carbonization with the increase of fixed carbons, the behavior of thermal degradation of torrefied biomass became significantly different according to the increase of torrefaction temperature. In conclusion, pelletization of PKS and EFB before torrefaction made it much easier to proceed with torrefaction of pellets from PKS and EFB, leading to excellent eco-friendly fuels.

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.1
• /
• pp.9-18
• /
• 2017

Arsenic (As) has been considered as the most toxic one among various hazardous materials and As contamination can be caused naturally and anthropogenically. Major forms of arsenic in groundwater are arsenite [(As(III)] and/or arsenate [(As(V)], depending on redox condition: arsenite and arsenate are predominant in reduced and oxidized environments, respectively. Because arsenite is much more toxic and mobile than arsenate, there have been a number of studies on the reduction of its toxicity through oxidation of As(III) to As(V). This study was initiated to develop photocatalytic oxidation process for treatment of groundwater contaminated with arsenite. The performance of two types of light sources (UV lamp and UV LED) was compared and the feasibility of goethite as a photocatalyst was evaluated. The highest removal efficiency of the process was achieved at a goethite dose of 0.05 g/L. Based on the comparison of oxidation efficiencies of arsenite between two light sources, the apparent performance of UV LED was inferior to that of UV lamp. However, when the results were appraised on the basis of their emitting UV irradiation, the higher performance was achieved by UV LED than by UV lamp. This study demonstrates that environmentally friendly process of goethite-catalytic photo-oxidation without any addition of foreign catalyst is feasible for the reduction of arsenite in groundwater containing naturally-occurring goethite. In addition, this study confirms that UV LED can be used in the photo-oxidation of arsenite as an alternative light source of UV lamp to remedy the drawbacks of UV lamp, such as long stabilization time, high electrical power consumption, short lifespan, and high heat output requiring large cooling facilities.

• Journal of Wetlands Research
• /
• v.24 no.4
• /
• pp.345-353
• /
• 2022

A wastewater treatment plant (WWTP) is a major gateway for the engineered nano-particles (ENPs) entering the water bodies. However existing studies have reported that many WWTPs exceed the No Observed Effective Concentration (NOEC) for ENPs in the effluent and thus they need to be designed or operated to more effectively control ENPs. Understanding and predicting ENPs behaviors in the unit and \the whole process of a WWTP should be the key first step to develop strategies for controlling ENPs using a WWTP. This study aims to provide a modeling tool for predicting behaviors and removal efficiencies of ENPs in a WWTP associated with process characteristics and major operating conditions. In the developed model, four unit processes for water treatment (primary clarifier, bioreactor, secondary clarifier, and tertiary treatment unit) were considered. Additionally the model simulates the sludge treatment system as a single process that integrates multiple unit processes including thickeners, digesters, and dewatering units. The simulated ENP was nano-sized TiO₂, (nano-TiO₂) assuming that its behavior in a WWTP is dominated by the attachment with suspendid solids (SS), while dissolution and transformation are insignificant. The attachment mechanism of nano-TiO₂ to SS was incorporated into the model equations using the apparent solid-liquid partition coefficient (Kd) under the equilibrium assumption between solid and liquid phase, and a steady state condition of nano-TiO₂ was assumed. Furthermore, an MS Excel-based user interface was developed to provide user-friendly environment for the nano-TiO₂ removal efficiency calculations. Using the developed model, a preliminary simulation was conducted to examine how the solid retention time (SRT), a major operating variable affects the removal efficiency of nano-TiO₂ particles in a WWTP.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.12
• /
• pp.792-800
• /
• 2012

The study was performed to simulate the reduction efficiency of suspended solids (SS) for cultivated land located at riverine area at the Namhan River and the Bukhan River watershed sites (site A, B, C) under the rainfall conditions using HUFF & SCS UH-based VFS Design module of Web GIS-based VFSMOD System. The study indicates that the field 5% sloped, located at Bukhan River watershed (site A), requires at least 0.5 m width of Vegetative Filter Strip (VFS) to reduce 70% of SS while the field 10% sloped requires the at least 1.0~1.5 m width of VFS to reduce 70% SS, under the condition 106.2 mm of rainfall event and bell pepper or corn of crops. Against the conditions 95.1 mm of rainfall event and sweet potato or soy bean of crops, the field 5% sloped, located at Namhan River watershed (site B) requires at least 0.5 m width of VFS to reduce 70% of SS while the field 10% sloped requires at least 1.0 m width of VFS to reduce 50% SS. The crops sweet potato and soy bean are cultivated in the site C, located at Namhan River watershed, 1 m of VFS is capable of 64.0% and 62.0% of SS reduction against 102.6 mm and 151.2 mm rainfall conditions respectively, for the 5% sloped field. The result supports that VFS is one of most potential methods to reduce SS from cultivated area, which is environment-friendly hydrologic structure. The VFS design, however, needs to be simulated before its installation in the field, the simulation needs to consider not only various characteristics of the field but also different conditions affecting the VFS, using a model capable to consider a lot of factors.