• Journal of Drive and Control
• /
• v.12 no.4
• /
• pp.21-27
• /
• 2015

The accurate position control of pneumatic driving apparatus is considered in this paper. In pneumatically actuated positioning systems, accurate positioning as an electrical servo has been known to be difficult because of the friction force and compressibility of the air. For good control performance of the pneumatic system, an actuator mounted with externally pressurized air bearings is produced to compensate for friction force. For the controller design, the governing equation of the pneumatic driving apparatus is derived. In order to reduce the nonlinear characteristics of the control valve, linearized control input is derived from the relation between the effective area of the valve and the control input. The experimental results are presented to show the results of the improved position control of the pneumatic driving apparatus.

• Journal of Drive and Control
• /
• v.14 no.4
• /
• pp.23-28
• /
• 2017

Time-delay control with internal model (TDCIM) is the controller for robot manipulators that applies the time-delay estimation and the concept of internal model control (IMC). TDCIM is robust against unknown dynamics and non-linear friction like coulomb friction and static friction. It is simple and computationally efficient. This study presents the relationship between the discrete TDCIM and the discrete PID controller. The PID controller is the most popular control law in the real application. But often the PID controller can be difficult to achieve the desired level of control performance. The result in this study provides a good candidate solution to these situations.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.478-483
• /
• 2005

This paper presents the comparison analysis of a Journal and thrust FDB (fluid dynamic bearing) and a conical FDB in a HDD spindle motor. The Reynolds equation is appropriately transformed to describe journal, thrust and conical bearing. Finite element method is applied to analyze the FDB by satisfying the continuity of mass and pressure at the interface between the hearings. The pressure field of the bearings is numerically approximated by applying the Reynolds boundary condition. The load and friction torque are obtained by integrating the pressure and the velocity gradient along the fluid film. The flying height of the spindle motor is measured to verify the proposed analytical result. This research shows that the conical bearing generates bigger load capacity and less friction torque than the journal and thrust bearing in a HDD spindle motor.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.4
• /
• pp.225-234
• /
• 2003

Turbo compressors need high speed rotating impeller in structure, high rate gearbox and conventional induction motor. This mechanical system increased moment of inertia and mechanical friction loss. Recently turbo compressor has adopted a super high-speed motor and driver and have made its size smaller and mechanical friction loss at minimum. In this paper, variable super high - speed motor controller, compressor controller and MMI controller are implemented with only one DSP (TMS320VC33) chip for a 150HP, 70,000rpm direct drive turbo compressor. It was required hardware and software integration. The result of integration, Controller hardware became simple and all control software are developed same developing tool. The implements turbo compressor meets the requirements.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.905-911
• /
• 2009

The viscosity drive method by the wheel which is widely used in the conventional railway systems needs a large friction force between the wheel and the guide-rail, which brings on a thrust force for a quick acceleration and a high-speed travelling. In addition, the viscosity drive method needs an increase of the vehicle weight for a large friction force. However, a maglev train is possible to be driven by the electro-magnet instead of the wheel, which produces a levitation and thrust force without any contact. In general, low-speed maglev train uses a linear induction motor(LIM) for propulsion that is operated under 300[km/h] due to the power-collecting and end-effect problems of LIM. In case of high-speed maglev train, a linear synchronous motor(LSM) is more suitable than LIM because of a high-efficiency and high-output properties. LSM has a driving principle as same as a conventional rotary synchronous motor(RSM), and the torque of RSM becomes the thrust force of LSM. A conventional LSM has relatively large air-gap compared with a conventional RSM. So, it must be achieved a design that is considered normal force by finite-asymmetric structure, end-effect on the entry and exit part, and support structure of a moving part. Therefore, in this research, authors accomplish a conceptualizing and basic design of a small-scaled LSM, and characteristics analysis using FEM.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.754-758
• /
• 2000

In recent years, the LDM(Linear DC Motor) is widely used, because it has more merits than other rotary motors. First, if system requires linear motion, LDM realizes direct linear motion as rotary motor does not. Second, system is simple and easy to control, and so on. In optical disc drive, a tracking system consists of two parts. One is fine actuating and the other is coarse actuating. For coarse actuating VCM(Voice Coil Motor) actuator is used as a basic drive mechanism. In this paper, MC(Moving Coil) type LDM is designed, manufactured and controlled. System is composed of mechanical-electromagnetic component, therefore mechanical loss and electromagnetic loss exist. The dominent mechanical loss is friction which results from sliding between guide shaft and hole. Therefore, this paper shows the friction compensation control. High speed and accurate position is not gained only PID control, therefore other control method is applied to the system.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.2
• /
• pp.19-24
• /
• 2022

The purpose of this research is to determine the hardness of guide hole. A guide pin and a guide hole of SSD(Solid State Drive) tester used to mount SSD in a fixed position accurately. The guide pin and guide hole are worn by friction due to repeated operation, and the wear is concentrated on the guide hole made of weak material rather than the guide pin made of relatively strong material. Because of that reason, it is often overdesigned in the design stage because it can lose its function. If the guide hole is made soft, the manufacturing cost will decrease, but the accuracy will decrease due to wear caused by repeated friction. If the guide hole is manufactured excessively, the manufacturing process becomes complicated and the manufacturing cost increases. It is essential to design a guide hole, but since there is no standard or verified data that can be referenced, it is difficult to design. Experimental device which guides in the same way as the SSD tester is used for this research, and three types of anodizing state are experimented for different hardness. Also, weight of COK(Change over Kit) were analyzed by measuring the wear amount and state of the guide hole according to the number of repeated attachment and detachment.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.2 s.233
• /
• pp.224-231
• /
• 2005

The present study investigates flow characteristics in an optical disc drive (ODD). Detailed knowledge of the flow characteristics is essential to analyze flow-induced noise and vibration, forced convection and flow friction loss. The ODD used in a personal computer is used for the experiment and rotating velocity of disc is under the 4500 rpm. Time-resolved velocity component and velocity spectrum are obtained using the laser Doppler anemometry (LDA), and the flow patterns induced by rotating disc in the ODD are calculated by a commercial finite volume method at the same time. The results show that the front holes reduce flow-induced noise and the position of pickup body only affects flow near the window. Furthermore, it is possible for cooling of heat sources in the drive through measuring the flow fields under the tray. In addition, the numerical results are well matched up to the experimental results, therefore, the validation of the numerical results can be achieved. From the validation of numerical results, it is possible to predict the flow characteristics of the region where it is unable to conduct the experiment.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1548-1553
• /
• 2003

The design of a high speed axial piston pump for hydrostatic transmission systems requires specific understanding on where and how much its internal frictional and flow losses are generated. In this study, the frictional loss of a bentaxis type hydraulic piston pump was analyzed in order to find out which design factors influence the mechanical efficiency most significantly. To this end, the friction coefficients of the sliding components were experimentally identified by a specially constructed tribometer. Applying them to the three-dimensional dynamic model of the pump presented by Doh and Hong [1], the friction torques generated by the sliding components such as piston head , bearing and valve plate were theoretically computed. The accuracy of the computed results was confirmed by the comparison with the experimentally measured mechanical efficiency. In this paper, it is shown that the viscous friction on the valve plate and the drive shaft bearing is the primary sources of the frictional losses of the bent-axis type pump, while the friction forces on the piston contribute to them only slightly.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.3
• /
• pp.40-46
• /
• 2021

An automatic transmission of automobiles enables comfortable driving experience with lower transmission shifting jerks. However, the assembly structure is more complicated and requires additional components with lower efficiency than the manual transmission system. Extensive research has been conducted to improve the overall transmission efficiency by optimizing each component of the automatic transmission assembly. This study focuses on enhancing the friction torque of double angular contact ball bearings used in automatic transmission. The friction torque of the bearing varies with the operating conditions such as the operational load and rotating speed. Since reducing the friction torque of the bearing tends to deteriorate the durability of the bearing, it is necessary to design the bearing having a minimum required friction torque by determining the durability life of an automatic transmission assembly, In this study, the theoretical life and friction torque of conventional and newly-developed bearings are calculated. The difference in the friction torque between the new and existing bearings are also evaluated.