• Asian-Australasian Journal of Animal Sciences
• /
• v.29 no.3
• /
• pp.444-454
• /
• 2016

This study was designed to examine the characteristics of sawdust and cocopeat bedding materials, including physicochemical properties (Exp. I) and on-farm trial (Exp. II). In Exp. I, the proportion of particle size was in the order of sawdust>cocopeat India>cocopeat Vietnam (p<0.05), and cocopeat contained higher proportion of small particles ($250{\mu}m$+below $250{\mu}m$) than sawdust, causing a dust production problem. Bulk density was cocopeat India>cocopeat Vietnam>sawdust (p<0.05), thus cocopeat treatments showed 4.4 times higher bedding cost than sawdust. The water absorption rates were 702.0% in cocopeat India, 678.3% in cocopeat Vietnam, and 444.0% in sawdust, showing cocopeat had approximately 1.5 times higher water absorption rate than sawdust. Moisture evaporation rates after 12 h of air blowing (2.00 m/s) were higher (p<0.05) in cocopeat Vietnam (80.4%) than sawdust (71.2%) and cocopeat India (72.8%). In vitro ammonia emissions were higher (p<0.05) in sawdust ($2.71mg/m^2/h$) than cocopeat India ($1.59mg/m^2/h$) and Vietnam ($1.22mg/m^2/h$), and total ammonia emissions were higher (p<0.05) in sawdust ($37.02mg/m^2$) than cocopeat India ($22.51mg/m^2$) and Vietnam ($13.60mg/m^2$). In Exp. II, an on-farm trial was conducted with 48 Hanwoo cattle in 16 pens using the same bedding materials as in Exp. I, with fan (blowing 2.00 m/s) and no fan treatments, and feed bunk side (FB) and water supply side (WS) within a pen (4.5 m, $width{\times}9.0m$, length). Beddings were replaced with fresh bedding materials when moisture concentrations were over 65%. No interactions among treatments were detected for moisture concentration and increment rates, and ammonia concentrations, but a significant effect was observed (p<0.01) for each of the treatments. Both concentrations and increment rate of moisture were higher (p<0.01) in the beddings without fan than with fan. Moisture concentrations and increment rate within a pen were also higher (p<0.01) in FB than WS. Thus, the whole no-fan-FB and sawdust-fan-FB were replaced with fresh bedding material between 4 to 5 experimental weeks. The ammonia concentrations and pH of beddings were not significantly different among treatments. Therefore, using cocopeat bedding with a blowing fan can extend twice the bedding utilization period, and WS within a pen showed twice the bedding-life compared to FB. Despite the outstanding characteristics of cocopeat compared with sawdust, using cocopeat as an alternative for sawdust bedding is not recommended for cattle management, considering it has 4.4 times higher bedding cost and a dust production problem.

• Journal of Science of Art and Design
• /
• v.6
• /
• pp.140-202
• /
• 2004

Body means 1)the whole structure and substance of a man, animal, or plant 2) the trunk or torso of a man or animal 3) part of garment that covers the trunk 4) the fresh or material substance, as opposed to the spirit. Human body could be distinguished as fresh and spirit. Body has the meaning of physicality. Physical means the bodily and constitution, but in the meaning of constitution there is the content of spirituality. Physicality means the appearing or arising of trace or image or nuance of body. The paintings which are using bodies are 1) directly draw bodies 2) twisting or transformation or nuance of the body and highly upgrade the physical emotion or fantastic bodily nuance 3) directly rubbing artist's body on the surface of painting with pigments to elect tactile specification. These physical art have appeared broadly by various artists, mainly with the social aspects of sex, drug, psycho sexual issues. In case of Joel peter Whitkin, the reason of strong physicality in the art is from the mind of the rejection and resistance of real world which is targeting top, perfect and beauty. Further explanation, being the world which is separated top and under, men and women, beauty and ugly; further in the situation, the hierarchy, terror and pressure began and many difficult problems has derived. The contents of attacking feminists's art works are very obscene to reveal female and male's phallus strongly. Sometime, it is strongly related in the political issues. The physical paintings have strong meanings in the action by hands and feet. It supports that it could reveal the humanity with smell, breath, and traces of bodies. In the bodies, the origin of life begins which gives human life by blood lines and water. Sometime, the physical paintings are made by the blood and urine to stick the physicality for special nuance. The physical paintings are made by the image of penis and clitoris which are related in the image of urinating, ejaculation and sometime is symbolized as pens and candles to drop liquid. The selected painters who are related in physical painting are Jackson Pollock, Andrea Serano, Eve Klein, Francis Bacon, Francesco Clemente, Lichard Long, Jakes & Dinos Chapman, Anselm Kiefer, Kiki Smith and Park, Ki Woong. Francis Bacon's style is destructive in representing human shapes which give us special message about the unbearable activity of men politician, high brain, wealthy and religious people. Francesco Clemente's method is to use throat, ear hole, mouse, clitoris, belly nostrils and every holes of body to transmute human physical body. Lichard Long uses directly his body in drawing the surface of painting by using liquid of mud Jakes & Dinos Chapman destroys or transforms the bodies of human. It sometime appears wrong location of the bodies that the penis and vulva is in between human faces or nose of women, Anselm Kiefer uses human hair for representing the human decaying martyrs, and indirectly using straw, he gives special ritual action to repent the Nazi's fault. From 2002 to 2003, Park KI Woong used women womb images to intermingle the smoke shape of <9.11 terror, 2001> in New York to reveal the painful situation of the time(*).

• Economic and Environmental Geology
• /
• v.38 no.2 s.171
• /
• pp.129-134
• /
• 2005

The $^{87}Sr/^{86}Sr$ ratios between water and biogenic material are similar in marine and lacustrine environment. Pb isotope ratios we, however, reported not to have been corresponding between the biological tissues and ambient water in aquatic system, contrary to the Sr isotope ratios. In order to explore the potential application of two isotopes as environmental tracers, we report here the isotopic compositions of strontium and lead of gastropod shell in fresh water in Jinan area. The $^{87}Sr/^{86}Sr$ ratios of carbonate shells of gastropod living in fresh stream water, are similar as that of ambient water but are different by sites. The different $^{87}Sr/^{86}Sr$ ratios of stream water between the sites is likely caused by the difference of the isotopic composition of Sr derived form rocks in the basin. In contrast, there is a distinct difference of the lead isotopic values between the water and the gastropod shell, suggesting that shell-fish available lead in aquatic system is different from dissolved lead in water. It is assumed that the majority of Pb in stream water is derived from atmospheric Pb accumulated on soil materials over years rather than from rock.

• Journal of Bio-Environment Control
• /
• v.17 no.3
• /
• pp.226-230
• /
• 2008

A comparison was made of the effect of different packaging materials on storability of mixed sprout vegetables (alfalfa, broccoli, cabbage, radish, and red radish) stored at $8^{\circ}C$. They were packaged by several kinds of films that were 50 fm thickness low-density polyethylene film (PE 50), 50 fm thickness polypropylene film (PP 50), $50{\mu}m$ thickness ceramic film (CE 50), $25{\mu}m$ thickness ceramic film (CE 25), $10\sim13{\mu}m$ thickness polyethylene film (wrap), and polyethylene terephthalate box with ventilation hole (box). The fresh weight of mixed sprouts packaged with different materials decreased below to 2% except box packages that decreased around 7% compared with initial weight. The atmospheres that were developed inside the different materials during storage differed significantly. The carbon dioxide and oxygen concentration of packages were kept properly with 5% in CE 25, but the PE 50 and CE 50 treatments showed higher carbon dioxide and lower oxygen concentration. So the off-flavor of mixed sprouts was more severe in the PE 50 and CE 50 treatment. The ethylene concentration of packages showed lowest in box treatment, followed by PP 50, wrap and CE 25 treatment. The overall quality of mixed sprouts was lower in PE 50 and CE 50 than CE 25 treatment after 10 days storage, supposed to be resulted from highest ethylene concentration and lowest oxygen concentration. Conclusionally, the CE 25 film that showed below 1% fresh weight loss, 5% carbon dioxide, 5% oxygen and below 4 ppm ethylene concentration in package may be a proper packaging material for mixed sprout vegetables.

• International Journal of Highway Engineering
• /
• v.16 no.5
• /
• pp.49-58
• /
• 2014

PURPOSES : In areas of high traffic volume, such as expressway across large cities, the amount of nitrogen oxides (NOx) emitted into the atmosphere as air pollution can be significant since NOx gases are the major cause of smog and acid rain. Recently, the importance of NOx removal has arisen in the world. Titanium dioxide ($TiO_2$), that is one of photocatalytic reaction material, is very efficient for removing NOx. The NOx removing mechanism of $TiO_2$ is the reaction of solar photocatalysis. Therefore, $TiO_2$ in road structure concrete need to be contacted with ultraviolet rays (UV) to be activated. In general, $TiO_2$ concretes are produced by replacement of $TiO_2$ as a part of concrete binder. However, considerable portion of $TiO_2$ in concrete cannot contact with the pollutant in the air and UV. Therefore, $TiO_2$ penetration method using the surface penetration agents is attempted as an alternative in order to locate $TiO_2$ to the surface of concrete structure. METHODS : This study aimed to evaluate the NOx removal efficiency of photocatalytic concrete due to various $TiO_2$ application method such as mix with $TiO_2$, surface spray($TiO_2$ penetration method) on hardened concrete and fresh concrete using surface penetration agents. The NOx removal efficiency of $TiO_2$ concrete was confirmed by NOx Analyzing System based on the specification of ISO 22197-1. RESULTS : The NOx removal efficiency of mix with $TiO_2$ increased from 11 to 25% with increasing of replacement ratio from 3 to 7%. In case of surface spray on hardened concrete, the NOx removal efficiency was about 50% due to application amount of $TiO_2$ with surface penetration agents as 300, 500 and 700g/m2. The NOx removal efficiency of surface spray on fresh concrete due to all experimental conditions, on the other hand, which was very low within 10%. CONCLUSIONS : It was known that the $TiO_2$ penetration method as surface spray on hardened concrete was a good alternative in order to remove the NOx gases for concrete road structures.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.32 no.6 s.107
• /
• pp.103-108
• /
• 2005

It was aimed to promote as a material for interior landscape by validating Rumohra aristata, in an indoor environment, especially irrigation interval, medium composition and drainage at indoor. 1. The result of physico-chemical analysis of medium composition showed that porosity, pH and Ex-Ca, Ex-Mg and Ex-K were high with peatmoss: vermiculite: perlite(1:1:1) and water contents, organic matter content, total nitrogen and cation exchange capacity were high with sand: leaf mold(1:1). 2. Growth and indoor adaptability of Rumohra aristata were better with irrigation at 2 interval per week than irrigation at 7 interval per week regardless of drainage. 3. In the case of medium composition, of growth and indoor adaptability were higher with sud: leaf mold (1:1) than peatmoss: vermiculite: perlite(1:1:1). 4. Fronds fresh weight and dry weight decreased when irrigation interval increased and were higher with sand: leaf mold(1:1) than peatmoss: vermiculite: perlite(1:1:1) treatment.

• Nuclear Engineering and Technology
• /
• v.52 no.3
• /
• pp.469-476
• /
• 2020

Research reactors in-core experimental facilities are designed to provide the highest steady state flux for user's irradiation requirements. However, fuel conversion from highly enriched uranium (HEU) to low enriched uranium (LEU) driven by the ongoing effort to diminish proliferation risk, will impact reactor physics parameters. Preserving the reactor capability to produce the needed flux to perform its intended research functions, determines the conversion feasibility. This study investigates the neutron flux in the central experimental facility of two material test reactors (MTR), the IAEA generic10 MW benchmark reactor and the 22 MW s Egyptian Test and Research Reactor (ETRR-2). A 3D full core model with three uranium enrichment of 93%, 45%, and 20% was constructed utilizing the OpenMC particle transport Monte Carlo code. Neutronics calculations were performed for fresh fuel, the beginning of life cycle (BOL) and end of life cycle (EOL) for each of the three enrichments for both the IAEA 10 MW generic reactor and core 1/98 of the ETRR-2 reactor. Criticality calculations of the effective multiplication factor (K_eff) were executed for each of the twelve cases; results show a reasonable agreement with published benchmark values for both reactors. The thermal, epithermal and fast neutron fluxes were tallied across the core, utilizing the mesh tally capability of the code and are presented here. The axial flux in the central experimental facility was tallied at 1 cm intervals, for each of the cases; results for IAEA 10 MW show a maximum reduction of 14.32% in the thermal flux of LEU to that of the HEU, at EOL. The reduction of the thermal flux for fresh fuel was between 5.81% and 9.62%, with an average drop of 8.1%. At the BOL the thermal flux showed a larger reduction range of 6.92%-13.58% with an average drop of 10.73%. Furthermore, the fission reaction rate was calculated, results showed an increase in the peak fission rate of the LEU case compared to the HEU case. Results for the ETRR-2 reactor show an average increase of 62.31% in the thermal flux of LEU to that of the HEU due to the effect of spectrum hardening. The fission rate density increased with enrichment, resulting in 34% maximum increase in the HEU case compared to the LEU case at the assemblies surrounding the flux trap.

• Journal of Bio-Environment Control
• /
• v.5 no.1
• /
• pp.50-56
• /
• 1996

This experiment was carried out to investigate the effects of new material, bioceramic powder in the nutrient solution(0.02%) and foliar spray(0.2%) on the growth and fruit quality of aeroponically grown tomato(Lycopersicon esculentum MILL. cv. Seokwang). Plant height was lowered, but root growth was increased both treatment of bioceramic powder into the nutrient solution and foliar spray. Cluster growth of tomato plants increased up to 14% over than that of control in the plot of foliar spray with bioceramic powder. Total plant dry weight also increased when bioceramic powder was treated both into the nutrient solution and foliar spray. T/R ratio was reduced by the treatment of bioceramic powder, but NAR and RGR showed the highest in the plot of foliar spray treated with 0.2% bioceramic powder than that of the other plots. Cumulative fruit fresh and dry weight were reduced when bioceramic powder was treated into nutrient solution but foliar spray produced more cumulative fruit fresh and dry weight than that of control. It was shown that treatment of bioceramic powder into the nutrient solution and foliar spray could be improved sugar degree without reducing fruit yields.

• Journal of Bio-Environment Control
• /
• v.12 no.2
• /
• pp.72-76
• /
• 2003

This study was conducted to estimate stimulation of plant growth of green and red leafy lettuces (Lactuca sutiva L. cv. Chungchima and Jugchima) at affected by covering method and time with protected film materials containing concentrated PO film and GA$_3$ foliar spray. Plants were covered with ‘Pasraido’ material from October 26 to November 31 (direct 1), from November 5 to November 31 (direct 2), or with a tunnel, or direct 2＋ tunnel. Mean air temperature and relative humidity under the covering were higher in direct and tunnel, direct and non-covering, in that order. The fresh weight and dry weight of red and green lettuces increased in direct and tunnel followed by direct 1, direct 2, tunnel and the control. GA$_3$ treatment promoted the growth in all covering methods, but decreased the chlorophyll contents. Fresh weight and dry weight were higher in red lettuce than in green lettuce in the control.

• Journal of the Korea Concrete Institute
• /
• v.25 no.6
• /
• pp.657-665
• /
• 2013

The purpose of this study is the basic research of self-compacting concrete using Alkali-Activated Slag (AAS) binder in order to emphasize the durability of structures and facilitate casting the fresh concrete in field. The AAS binder emitted low carbon dioxide ($CO_2$) is eco friendly material of new concept because AAS products not only emit little $CO_2$ during production but also reuse the industrial by-products such as ground granulated blast-furnace slag (GGBS) of the steel mill. Until now, almost of domestic and foreign research are using Ordinary Portland Cement (OPC) for self-compacting concrete, and also, nonexistent research about AAS. The self-compacting concrete must get the performance of flowability, segregation resistance, filling and passing ability. Nine concrete mixes were prepared with the main parameter of unit amount of binder (400, 500, 600 $kg/m^3$) and 3 types of water-binder (W/B) ratio. The results of test were that fresh concretes were satisfied with flowability, segregation resistance, and filling ability of JSCE. But the passing ability was not meet the criteria of EFNARC because of higher viscosity of AAS paste than OPC. This high viscosity of AAS paste enables the manufacturing of self compacting concrete, segregation of which does not occur without the using of viscosity agent. It is necessary that the development of high fluidity AAS binders of higher strength and the study of better passing ability of AAS concrete mixes in order to use self compacting AAS concrete in field.