• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.12
• /
• pp.24-30
• /
• 1996

In this paper, we designed a new type of high frequency on-chip voltage controlled oscillator (VCO) using GaAs MESFET, and their performances were comapred with those of the conventional VCO. Each VCO was designed with three-to-five ring oscillator and inverter, buffer and NOR gate were implemented by GaAs source coupled FET logic, which has better speed and noise performance compared to other GaAs MESFET logic. SPICE simulation showed that the gain of conventional and our new VCO was 1.24[GHz/V], 0.54[GHz/V], respectively. The frquency tuning range were 2.31 to 3.55 [GHz] for conventional VCO and 2.47 to 3.01[GHz] for our new design. This shows that the factor of two gain reductin was achieved without too much sacrifice in the oscillation frequency. For our new VCO, the average temperature index was -2[MHz/.deg. C] in the range of -20~85[.deg. C] the power supply noise index was 5[MHz/%] for 5.3[V].+-.10[%] and total power consumption was 60.58[mW].

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.3
• /
• pp.424-433
• /
• 2001

We present a new electrostatic repulsive-force microactuator using a lateral repulsive force induced by an asymmetric distribution of electrostatic field. The lateral repulsive force has been characterized by a simple analytical equation, derived from a finite element simulation. A set of repulsive force polysilicon microactuators has been designed and fabricated by a 4-mask surface-micromachining process. Static and dynamic micromechanical behavior of the fabricated microactuators has been measured at the atmospheric pressure for a varying bias voltage. The static displacement of the fabricated microactuator, proportional to the square of the DC bias voltage, is obtained as 1.27 $\mu\textrm{m}$ for the DC bias voltage of 140V. The resonant frequency of the repulsive-force microactuator increases from 11.7 kHz to 12.7 kHz when the DC bias voltage increases from 60V to 140V. The measured quality-factor varies from 12 to 13 for the bias volatge range of 60V∼140V. The characteristics of the electrostatic repulsive-force have been discussed and compared and compared with those of the conventional electrostatic attractive-force.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.302-307
• /
• 2001

This research is concerned with the development of a real-time adaptive PPF controller for the active vibration suppression of smart structure. In general, the tuning of the PPF controller is carried out off-line. In this research, the real-time learning algorithm is developed to find the optimal filter frequency of the PPF controller in real time and the efficacy of the algorithm is proved by implementing it in real time. To this end, the adaptive algorithm is developed by applying the gradient descent method to the predefined performance index, which is similar to the method used popularly in the optimization and neural network controller design. The experiment was carried out to verify the validity of the adaptive PPF controller developed in this research. The experimental results showed that adaptive PPF controller is effective for active vibration control of the structure which is excited by either impact or harmonic disturbance. The filter frequency of the PPF controller can be tuned in a very short period of time thus proving the efficiency of the adaptive PPF controller.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.12
• /
• pp.5745-5758
• /
• 2017

In this paper, we develop a simple but very effective 4 by 4 Multiple-Input Multiple-Output (MIMO) antenna system for mobile phones consisting of different types of antennas to achieve low correlation property at the frequency ranges of 1710 to 2170 MHz, which covers wide LTE service bands, from band 1 to band 4. The proposed antenna system consists of two pair of antennas. Each pair consists of a planar inverted-F antenna (PIFA) and a coupling antenna which has the property of the loop. The use of two different antenna types of IFA and a coupling achieves high isolation. Proposed antenna system occupies relatively small area and positions at the four corners of a printed circuit board. The gap between the two antennas is 4 mm, in order to realize the good isolation performance. To evaluate the performance of our proposed antenna system, we perform various experiments. The proposed antenna shows a wide operating bandwidth greater than 460 MHz with isolation between the feeding ports higher than 17.5-dB. It also shows that the proposed antenna has low Envelop Correlation Coefficient (ECC) values smaller than 0.08 over the all desired frequency tuning ranges.

• International journal of advanced smart convergence
• /
• v.9 no.1
• /
• pp.172-176
• /
• 2020

The implementation of a low phase noise voltage controlled oscillator (VCO) is important for the signal integrity of wireless communication terminal. A low phase noise wideband VCO for a wireless local area network (WLAN) application is presented in this paper. A 6-bit coarse tune capacitor bank (capbank) and a fine tune varactor are used in the VCO to cover the target band. The simulated oscillation frequency tuning range is from 8.6 to 11.6 GHz. The proposed VCO is desgned using 65 nm CMOS technology with a high quality (Q) factor bondwire inductor. The VCO is biased with 1.8 V VDD and shows 9.7 mA current consumption. The VCO exhibits a phase noise of -122.77 and -111.14 dBc/Hz at 1 MHz offset from 8.6 and 11.6 GHz carrier frequency, respectively. The calculated figure of merit(FOM) is -189 dBC/Hz at 1 MHz offset from 8.6 GHz carrier. The simulated results show that the proposed VCO performance satisfies the required specification of WLAN standard.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.6
• /
• pp.81-89
• /
• 1996

Quantum RF impedance of SIS (superconductor insulator superconductor) junction has been analyzed by using through on tucker's quantum mixer theory in the frequency range form 80 GHz to 120 GHz. The embedding impedance of waveguide-type mixer mount and its equivalent circuit have been evaluated. From these evaluated results, the impedance matching efficiency between mixer mount embedding impedance and mixer port impedance of upper-side band and IF which were determined by augmented admittance matrix with given backshort position has been discussed in detail. It is found that the mixer with fixed backshort mount ahs a impedance matching efficiency about 80% at each port of mixer within 85GHz to 115GHz, which implys a conversion los of mixer would be good enough to be operated such a wide band frequency range. Therefore, the theoretical evaluated results show that our method can be used ot design the mixer mount without any mechanical tuning elements such a backshort or an E-plane tunners for wide band operation.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.155-159
• /
• 2003

This paper presents fully integrated 5 GHz band low phase noise LC tank VCO. The implemented VCO is tuned by integrated PN diode and tuning rage is $5.01{\sim}5.30$ GHz under $0{\sim}3 V$ control voltage. For good phase noise performance, LC filtering technique, common in Si CMOS process, is used, and to prevent degradation of phase noise performance by collector shot-noise and to reduce power dissipation the HBT is biased at low collector current density bias point. The measured phase noise is -87.8 dBc/Hz at 100 kHz offset frequency and -111.4 dBc/Hz at 1 MHz offset frequency which is good performance. Moreover phase noise is improved by roughly 5 dEc by LC filter. It is the first experimental result in InGaP/GaAs HBT process. The figure of merit of the fabricated VCO with LC filter is -172.1 dBc/Hz. It is the best result among 5 GHz InGaP HBT VCOs. Moreover this work shows lower DC power consumption, higher output power and more fixed output power compared with previous 4, 5 GHz band InGaP HBT VCOs.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.3
• /
• pp.565-570
• /
• 2012

This paper has proposed a multi-channel low pass filter (LPF) for LTE-Advanced systems. The proposed LPF is an active-RC 5th chebyshev topology with three cut-off frequencies of 5 MHz, 10 MHz, and 40 MHz. A 3-bit tuning circuit has been adopted to prevent variations of each cut-off frequency from process, voltage, and temperature (PVT). To achieve a high cut-off frequency of 40 MHz, an operational amplifier used in the proposed filter has employed a PMOS cross-connection load with a negative impedance. A proposed filter has been implemented in a 0.13-${\mu}m$ CMOS technology and consumes 20.2 mW with a 1.2 V supply voltage.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.6
• /
• pp.1188-1193
• /
• 2009

Todays, many young people suffer from noise-induced hearing loss by using wearable hearing devices, such as Bluetooth headset. This paper present hearing loss reduction and more natural volumn control algorithms considering individual hearing characteristics and threshold of feeling for Bluetooth headset. Experimental results using CSR Bluetooth headset example design board(DEV-PC-1645) show that individuals maybe able to perceive without the inconvenience at the less sound intensity and the more sensitive frequency bands. As a result, we may prevent hearing loss to reduce excessive sound energy in each frequency bands.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.506-510
• /
• 2016

A triple-band (TB) oscillator was implemented in the TSMC $0.18{\mu}m$ 1P6M CMOS process, and it uses a cross-coupled nMOS pair and two shunt $4^{th}$ order LC resonators to form a $6^{th}$ order resonator with three resonant frequencies. The oscillator uses the varactors for band switching and frequency tuning. The core current and power consumption of the high (middle, low)- band core oscillator are 3.59(3.42, 3.4) mA and 2.4(2.29, 2.28) mW, respectively at the dc drain-source bias of 0.67V. The oscillator can generate differential signals in the frequency range of 8.04-8.68 GHz, 5.82-6.15 GHz, and 3.68-4.08 GHz. The die area of the triple-band oscillator is $0.835{\times}1.103mm^2$.