• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.840-848
• /
• 2016

A primary-side regulation AC-DC converter operating in the PFM (Pulse Frequency Modulation) mode with a high precision output current is designed, which applies a novel inductance compensation technique to improve the precision of the output current, which reduces the bad impact of the large tolerance of the transformer primary side inductance in the same batch. In this paper, the output current is regulated by the OSC charging current, which is controlled by a CC (constant current) controller. Meanwhile, for different primary inductors, the inductance compensation module adjusts the OSC charging current finely to improve the accuracy of the output current. The operation principle and design of the CC controller and the inductance compensation module are analyzed and illustrated herein. The control chip is implemented based on a TSMC 0.35μm 5V/40V BCD process, and a 12V/1.1A prototype has been built to verify the proposed control method. The deviation of the output current is within ±3% and the variation of the output current is less than 1% when the inductances of the primary windings vary by 10%.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.6
• /
• pp.432-440
• /
• 2010

In this paper, a LC series resonant boost converter using a single switch is proposed. The proposed topology contains additional passive elements in the conventional boost converter and performs Zero Voltage Switching(ZVS) without an additional auxiliary switch when a main switch turned on and off. The switch off time of the proposed system determined by LC series resonance, thus a on-time variable Pulse Frequency Modulation(PFM) method is adapted to control output voltage in the proposed converter. Operational modes of the proposed topology are divided with respected to the current conduction paths and then through the theoretical analysis and experimental results, operational modes and characteristics of the proposed converter are verified.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.22 no.5
• /
• pp.404-413
• /
• 2017

This paper suggests an isolated PFC converter for electric vehicle (EV) chargers with wide-output voltage range. The proposed converter is based on voltage-fed full-bridge structure. All the harmonic and output controls are performed by secondary and primary switches are only operated under a fixed frequency with 50% duty-ratio. In addition, harmonic modulation technique is adopted to obtain a near unity power factor without input current monitoring. The feasibility of the proposed charger has been verified with a 10-kW prototype.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.1A
• /
• pp.1-12
• /
• 2002

Ultra Wideband (UWB) system uses wide band signal, which power spectral density likes as a noise floor, so UWB system can be used high speed communication without interfering with other communication system. As this system doesn't use radio frequency carrier. Its structure would be very simple and consume very low power. For the first time, we adopted Rayleigh monopulse multiple access system. And under the AWGN, we analysis and compare error probability, the number of user and data rate of the two methods that pulse position modulation and antipodal. In the result, We concluded that the antipodal method had much better probability of error, the number of user and data rate than PPM.

• Journal of Communications and Networks
• /
• v.13 no.4
• /
• pp.313-318
• /
• 2011

When wireless channels undergo fast fading, non-coherent frequency shift keying (FSK) (de)modulation schemes may be considered for amplify-and-forward (AF) cooperative communications. In this paper, we derive the bit-error-rate performance of partial non-coherent receiver as a lower bound of the optimal non-coherent receiver for FSK modulated AF cooperative communications. From the simulation and analytical results, it is found that the derived lower bound is very closed to simulation results. This result shows that knowing partial channel state information may not improve system performance significantly. On the other hand, conventional optimal non-coherent receiver involves complicated integration operation. To address the above complexity issue, we also propose a near optimal non-coherent receiver which does not involve integration operation. Simulation results have shown that the performance gap between the proposed near optimal receiver and the optimal receiver is small.

• Proceedings of the KIEE Conference
• /
• 1998.07c
• /
• pp.908-910
• /
• 1998

Modern AC electric car has PWM(Pulse Width Modulation) -controlled converters, which give rise to higher harmonics. The current harmonics injected from AC electric car is propagated through power feeding circuit. As the feeding circuit is a distributed constant circuit composed of RLC, the capacitance of the feeding circuit and the inductance on the side of power system cause a parallel resonance and a magnification of current harmonics at a specific frequency. The magnified current harmonics usually brings about various problems. That is, the current harmonics makes interference in the adjacent lines of communications and the railway signalling system. Furthermore, in case it flows on the side of power system, not only overheating and vibration at the power capacitors but also wrong operation at the protective devices can occur. Therefore, the exact assessment of the harmonic current flow must be undertaken at design and planning stage for the electric traction systems. From these point of view, this study presents an approach to model and to analyse traction power feeding system focused on the amplification of harmonic current. The proposed algorithm is applied to a standard AT(Auto-transformer)-fed test system in which electric car with PWM-controlled converters is running.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.5
• /
• pp.431-435
• /
• 2009

The apparatus has been fabricated using the laser diode and microprocessor unit. The apparatus used a InGaAlP laser diode for laser medical therapy and was designed for a pulse width modulation type to increase stimulation effects. To raise the stimulus effect of the human body, the optical irradiation frequency could be set up. The study has executed in-vivo experiment by employing our own developed laser diode irradiation system to investigate the effects of the InGaAlP laser diode irradiation on the wound healing as a preliminary study aimed at the application of InGaAlP laser diode to wound healing of human skin injury. The study cut out whole skin layers of Sprague-Dawley rat on the back part in 1 cm circle and observed developing effects after executing light irradiation for 9 days, and in result it is found that the light irradiation rat showed earlier wound healing than non-irradiation rat during the experimental period. In addition, there are some differences found regarding the healing process between laser diode irradiated rats and non-irradiated ones.

• Journal of the Korean Chemical Society
• /
• v.57 no.2
• /
• pp.272-278
• /
• 2013

Extract of ginger has been evaluated as a green inhibitor for the corrosion of steel in sulfide polluted NaCl solution using potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) and electrochemical frequency modulation (EFM) techniques. Potentiodynamic polarization measurements showed that this extract acts as a mixed type inhibitor but mainly inhibits the cathodic reaction. The inhibition efficiency was found to increase with inhibitor concentration reaching to approximately 83.9% using 250 ppm of ginger. Nyquist plots show a single capacitive loop in uninhibited and inhibited solutions. From EFM the causality factors are very close to theoretical values which indicate that the measured data are of good quality. The adsorption process of the studied extract on steel surface obeys Temkin adsorption isotherm. The results obtained from the different electrochemical techniques were in good agreement which prove the validity of these tools in measurement of corrosion rate. Ginger extract has no effect on Escherichia Coli and can be applied safely on waste water treatment plants.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.672-675
• /
• 2010

Spray characteristics for the modulation with a pulsed spray in low-frequency region were investigted by performing with additional internal pulsed injection. The 1st perturbative flow was generated by rotating-type pulsed device and the 2nd pulse source generated by the magnetic valve was used to modulate the 1st flow. A pattern of the modulated spray was observed through FFT result and visualization. In case of modulated spray with the 2nd pulse control, the width of up and down motion of the modulated spray is smaller than that of the spray without the 2nd pulse. Also, the depth of penetration of the down stream is higher than that of spray without the 2nd pulse.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.3
• /
• pp.296-304
• /
• 2001

A new method of measuring the thermal diffusivity of solid material at room temperature using photothermal displacement is proposed. The influence of the parameters, such as radius and modulation frequency of the pump beam and the sample thickness, was studied. From the minimum position of phase of measured deflection with respect to the pump beam, the thermal diffusivity of the materials can be obtained. The position where phase has the minimum value is determined using multiparameter least-square regression fitting. The experimental values for different samples obtained by applying the new method are in good agreement with the literature values.