• Proceedings of the KSRS Conference
• /
• 2007.10a
• /
• pp.540-543
• /
• 2007

The modulation transfer function (MTF) in a camera system is a measurement of how well the system will faithfully reproduce the original scene. The electro-optical camera system consists of optics, an array of pixels, and an electronics which is related to the image signal chain. The system MTF can be cascaded with each element's MTF in the frequency domain. That is to say, the electronics MTF including the detector MTF can be recalculated easily by the acquired system MTF if the well-known test optics is used in the measuring process. A Time-Delay and Integration (TDI) detector can make a signal increase by taking multiple exposures of the same object and adding them. It can be considered the various methods to measure the MTF of the TDI camera system. This paper shows the actual and practical MTF measuring methods for the detector and electronics in the TDI camera. The several methods are described according to the scan direction as well as the TDI stages such as the single line mode and the multiple-lines mode. The measuring is performed in the in the static condition or dynamic condition to get the point spread function (PSF) or the line spread function (LSF). Especially, the dynamic test bench is used to simulate on track velocity to synchronize with TDI read out frequency for the dynamic movement.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.3
• /
• pp.279-286
• /
• 2006

A method for estimating the instantaneous phasor of a fault current signal is proposed for high-speed distance protection that is immune to a DC-offset. The method uses a modified notch filter in order to eliminate the power frequency component from the fault current signal. Since the output of the modified notch filter is the delayed DC-offset, delay compensation results in the same waveform as the original DC-offset. Subtracting the obtained DC-offset from the fault current signal yields a sinusoidal waveform, which becomes the real part of the instantaneous phasor. The imaginary part of the instantaneous phasor is based on the first difference of the fault current signal. Since a DC-offset also appears in the first difference, the DC-offset is removed trom the first difference using the results of the delay compensation. The performance of the proposed method was evaluated for a-phase to ground faults on a 345kV 100km overhead transmission line. The Electromagnetic Transient Program was utilized to generate fault current signals for different fault locations and fault inception angles. The performance evaluation showed that the proposed method can estimate the instantaneous phasor of a fault current signal with high speed and high accuracy.

• Journal of Sensor Science and Technology
• /
• v.16 no.5
• /
• pp.349-354
• /
• 2007

This paper presents characteristics of surface acoustic wave (SAW) gas sensor for detecting volatile gases such as ethanol gas by measuring the phase shift of output signal. A delay-line with a center frequency of 400 MHz was fabricated on $128^{\circ}$ Y-Z $LiNbO_{3}$ substrates. Experimental results, which showed the phase change of the output signal under the absorption of volatile gas on sensor surface, were presented. The sensitivities of SAW delay lines coated with polyurethane films were greatly increased compared to those for uncoated devices. This SAW gas sensor system may be well suited for a high sensitivity electronic nose system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.6
• /
• pp.539-547
• /
• 1992

Considering the field of high frequency or broad-band signal filtering with high speed, we pro-pose optical fiber filters which consist of directional couplers and optical fiber delay elements. Fiber delay line signal processor Is operated with Incoherent optical carrier because of Its simplicity. Due to the characteristics of the directional coupler which Is basic element of optical fiber filter a new design method which Is different from that of usual digital filter is required. By considering the characteristics of directional coupler and in order to make good use of the optical signal energy, we have given the design formulae and the conditions of optical fiber filters for the direct and the lattice form.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.364-364
• /
• 2007

This paper presents characteristics of surface acoustic wave (SAW) gas sensor for detecting volatile gases such as ethanol gas by measuring phase shift of output signal. A delay-line with a center frequency of 400MHz was fabricated on 128o Y-Z $LiNbO_3$ substrates. Experimental results, which show the phase change of output signal under the absorption of volatile gas on sensor surface, were presented. The sensitivities of SAW delay lines coated with polyurethane films are greatly increased compared to those for uncoated devices. This SAW gas sensor system may be well suited for a high sensitivity electronic nose system.

• The Journal of the Acoustical Society of Korea
• /
• v.24 no.3
• /
• pp.160-165
• /
• 2005

We have developed SH (shear horizontal) surface acoustic wave (SAW) sensors for detection of the immobilization and hybridization of DNA (deoxyribonucleic acid) on the gold coated delay line of transverse SAW devices. The experiments of DNA immobilization and hybridization were performed with 15-mer oligonucleotides (probe and complementary target DNA). The sensor consists of twin SAW delay line oscillators operating at 100 MHz fabricated on $36^{\circ}$ rotated Y-cut $LiTaO_3$ piezoelectric single crystals. The relative change in the frequency of the two oscillators was monitored to detect the hybridization between target DNA and immobilized probe DNA in pH 7.4 PBS (phosphate buffered saline) solution. The measurement results showed a good response of the sensor to the mass loading effects of the DNA immobilization and hybridization with the sensitivity up to $1.55{\cal}ng/{\cal}ml/Hz$.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.5
• /
• pp.76-84
• /
• 2007

In this paper, we measured the propagation characteristics of I-UWB channel in time domain and in frequency domain. The measurements carried out in apartment environment while furniture and household electric appliance. Typical indoor scenarios, including line-of-sight(LOS), non-line-of-sight(NLOS) in room-to-room, within-the-room. A transmitting and receiving antenna is a biconical antenna. Results for indoor propagation measurements are presented for power delay profiles(PDP). We extracted the channel characteristic parameters from a power delay profile. Finally, we designed I-UWB channel model in indoor environment, and I-UWB simulator. The results of simulation shows BER characteristics below $10^{-5}$ for SNR over 20[dB].

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.11
• /
• pp.1186-1193
• /
• 2009

In this paper, we propose DDS(Direct Digital Synthesizer) as a new implementation method of chirp LO(Local Oscillator) for compressive receiver applied for RFID signal detection in UHF band. We designed a receiver whose input frequency range is 908.5~914 MHz, DDL(Dispersive Delay Line) bandwidth is 6 MHz, and dispersion delay time is $13\;{\mu}s$. Chirp LO based on DDS is designed to meet $26\;{\mu}s$ sweep time and 12 MHz bandwidth for complete compressive mechanism. The measured 3 dB pulse width of the compressed signal of the fabricated receiver is 260 ns and the frequency resolution for simultaneous input signals is below 200 kHz. These performances indicate that the proposed chirp LO based on DDS and the compressive receiver is suitable for RFID signal detection in UHF band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.3
• /
• pp.321-330
• /
• 2010

In this paper, the theoretical background and the specific implementation method of a compressive receiver for RFID signal detection as well as the design method of DDL(Dispersive Delay Line) and chirp LO are described. DDL, which is one of the main components of the compressive receiver, is designed to have $13{\mu}s$ dispersive delay time and 6 MHz bandwidth using the SAW technique based on $LiNbO_3$ material. The chirp LO is designed using DDS(Direct Digital Synthesizer). Also the compressive receiver is fabricated to be installed into the RFID reader. Test results show the maximum frequency error of 25 kHz for single signal input, the receiver sensitivity of -44 dBm, and the maximum frequency error is 75 kHz for 6 multi-tone input signals. These results indicate that the fabricated compressive receiver is working well even in dense RFID operating environments.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.1
• /
• pp.74-84
• /
• 2007

This paper presents a new dual-loop Delay Locked Loop(DLL) to expand the delay lock range of a conventional DLL. The proposed dual-loop DLL contains a Coarse_loop and a Fine_loop, and its operation utilizes one of the loops selected by comparing the initial time-difference among the reference clock and 2 internal clocks. The 2 internal clock signals are taken, respectively, at the midpoint and endpoint of a VCDL and thus are $180^{\circ}$ separated in phase. When the proposed DLL is out of the conventional lock range, the Coarse_loop is selected to push the DLL in the conventional lock range and then the Fine_loop is used to complete the locking process. Therefore, the proposed DLL is always stably locked in unless it is harmonically false-locked. Since the VCDL employed in the proposed DLL needs two control voltages to adjust the delay time, it uses TG-based inverters, instead of conventional, multi-stacked, current-starved inverters, to compose the delay line. The new VCDL provides a wider delay range than a conventional VCDL In overall, the proposed DLL demonstrates a more than 2 times wider lock range than a conventional DLL. The proposed DLL circuits have been designed, simulated and proved using 0.18um, 1.8V TSMC CMOS library and its operation frequency range is 100MHz${\sim}$1GHz. Finally, the maximum phase error of the DLL locked in at 1GHz is less than 11.2ps showing a high resolution and the simulated power consumption is 11.5mW.