• Korean Chemical Engineering Research
• /
• 제54권5호
• /
• pp.630-635
• /
• 2016

선행연구에서는 2차오염이 없는 물리적 처리방법인 전단응력을 이용한 선박평형수 처리장치에 대하여 연구하였다. 정지상태의 외부 실린더와 회전하는 내부 실린더 사이에 발생하는 전단응력을 이용하여 다양한 미생물을 파쇄 처리하는 원리이며, 전단응력은 실린더 표면의 형태나 회전속도에 따라 크기가 달라진다. 전단응력의 크기와 전단응력을 받는 시간에 따라 멸균정도가 차이를 보이기 때문에, 다양한 조건에 따른 멸균효율을 밝히는 실험이 필요하며 이를 통해 상업용 장치의 제작을 위한 기초 자료를 마련하고자 하였다. 선행연구에서는 disk type과 cylinder type의 비교를 통하여 cylinder type이 우수함을 밝혔다. 본 연구에서는 선행연구를 통하여 얻은 결과를 바탕으로 cylinder type, groove type, knurling type의 표면 조건을 변화시켜 가장 우수한 조합을 밝혀냄과 동시에 실린더 사이의 간격에 따른 회전속도 및 유속 조건을 최적화 하고자하였다. 그 결과 groove type에서 250 mL/min의 유량조건에서는 8000 rpm 이상, 혹은 500 mL/min의 유량조건에서는 10000 rpm 이상에서 100% 살균 처리되는 결과를 얻었다.

• 한국전산유체공학회지
• /
• 제13권4호
• /
• pp.126-134
• /
• 2008

We developed a three dimensional Navier-Stokes code based on the level set method to simulate two phase flows with high density ratio. The Navier-Stokes equations with consideration of the surface tension effects are solved by using SIMPLE algorithm on a non-staggered grid. The present code is validated by simulating two test problems. First one is to simulate a rising bubble inside a cube. The thickness of the interface of the bubble is shown to affect the pressure distribution around the interface. As the thickness decreases, the pressure field around the interface becomes more oscillatory. As the bubble rises, a ring vortex is shown to form around the interface and the bubble eventually develops into an ellipsoidal shape. Merge of two bubbles inside a container is secondly tested to show the robustness of the present code for two phase flow simulation. Numerical results show stable and reliable behavior during the process of merging of two bubbles. The velocity and pressure fields around the interface of bubbles are shown oscillation free during the merging of two bubbles.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.1-6
• /
• 2011

In this study, wind tunnel test were conducted to improve an aerodynamic performance of HEMU400X pantograph system with 4 types of pantograph housing models. Experimental models were 1/4 scaled pantograph system, 1/4 scaled ground plate which is scaled down to real roof shape of HEMU-400x, and 4 types of pantograph housing models. The free stream of wind tunnel were 20, 40, 60, 70m/s. The lift and drag forces were measured with 2-axis load cell. And, Total pressure were measured with rake in the wake region of panhead. In addition, Surface flow visualization by tufts were performed to know flow characteristics around pantograph housing. According to the results of force tests and surface visualizations, pantograph housing shape is important part because the shape affects to pantograph system. Therefore, it is considered that adaption of pantograph housing is more advantageous to decrease drag and acoustic noise.

• 대한기계학회논문집B
• /
• 제21권7호
• /
• pp.919-927
• /
• 1997

The main purpose of this study is to determine bifurcation as the primary instability of a glass melting furnace. Steady-state and unsteady characteristics of natural convection in the partially open cavity as appeared in a glass melting furnace is investigated by using numerical analysis. Three types of convection, such as steady laminar, unsteady periodic or unsteady quasi-periodic convection may occur according to the temperature difference between upper two isothermal surfaces along the depth of cavity in a glass melting furnace. In the temperature difference of 150-900 K between batch and free surface, the larger the temperature difference, the weaker the convection strength and unsteadiness. Since the glass viscosity is increasing exponentially in the lower temperature, the batch freezes the thermofluidic field especially below the surface of it. If the depth of cavity is 0.5 m, the bifurcation to time-dependent natural convection may occur in the range of 60-650 K. If that is 1.0 m, it may occur in the whole range of temperature difference.

• 한국주조공학회지
• /
• 제18권6호
• /
• pp.570-577
• /
• 1998

An investigation has been conducted to describe solidification characteristics in Sn-Zn binary system and Sn-Zn-Ag ternary system added by Ag produced by the continuous casting process using heated mold as a basic study for developing Pb-free solder materials. To obtain the continuous casting rods with mirror surface and near net shape at higher casting speed, water flow rates must be increased and mold temperature must be lowered. However, surface tearing in the casting rods occured at lower continuous casting speed while break out occured at higher continuous casting speed even if optimum conditions such as water flow rate and heated mold temperature are determined. Primary ${\alpha}Sn$ and eutectic structure in unidirectioally solidified Sn-Zn alloys were finer with increased casting speed. But, directionality may not be expected for primary Zn in hypereutectic Sn-Zn alloy. It was found that the addition of $0.2{\sim}0.8%$ Ag promoted the growth of primary ${\alpha}Sn$ dendrites. The changes of tensile strength and elongation in Sn-Zn binary alloys were not observed while the increase of tensile strength and the decrease of elongation in Sn-Zn-Ag ternary alloys were observed with increased casting speed.

• 대한기계학회논문집B
• /
• 제25권2호
• /
• pp.164-170
• /
• 2001

The influence of unsteady wake on the flow and heat transfer characteristics in a four-vane linear cascade was experimentally investigated. The unsteady wake was generated with four rotating rectangular plates located upstream of the cascade. Tested inlet Reynolds number based on chord length was set to 66,000 by controlling free-stream velocity. A hot-wire anemometer system was employed to measure turbulent velocity components. For the convective heat transfer coefficients measurement on turbine blade surface, thermochromic liquid crystal and gold film Intrex were used. It was found that the unsteady wake enhances the turbulent motion in the cascade passage and accordingly promotes the development and transition of boundary layer. It was found that the heat transfer coefficients on the blade surface increase as the plate rotating speed increases. However, the increasing of heat transfer coefficients is not significant in the case that Strouhal number is higher than 0.503.

• 대한조선학회논문집
• /
• 제44권4호
• /
• pp.398-407
• /
• 2007

A smoothed particle hydrodynamics (SPH) method is applied for simulating two-dimensional free-surface problems. The SPH method based on the Lagrangian formulation provides realistic flow motions with violent surface deformation, fragmentation and reunification. In this study, the effect of computational parameters in SPH simulation is explored through two-dimensional dam-breaking and sloshing problem. The parameters to be considered are the speed of sound, the frequency of density re-initialization, the number of particle and smoothing length. Through a series of numerical test. detailed information was obtained about how SPH solution can be more stabilized and improved by adjusting computational parameters. Finally, some numerical simulations for various fluid flow problem were carried out based on the parameters chosen through the sensitivity study.

• Advances in concrete construction
• /
• 제15권5호
• /
• pp.303-312
• /
• 2023

The present study investigates the effects of Cattaneo-Christov thermal effects of stagnation point in Walters-B nanofluid flow through lubrication of power-law fluid by taking the slip at the interfacial condition. For the solution, the governing partial differential equation is transformed into a series of non-linear ordinary differential equations. With the help of hybrid homotopy analysis method; that consists of both the homotopy analysis and shooting method these equations can be solved. The influence of different involved constraints on quantities of interest are sketched and discussed. The viscoelastic parameter, slip parameters on velocity component and temperature are analyzed. The velocity varies by increase in viscoelastic parameter in the presence of slip parameter. The slip on the surface has major effect and mask the effect of stagnation point for whole slip condition and throughout the surface velocity remained same. Matched the present solution with previously published data and observed good agreement. It can be seen that the slip effects dominates the effects of free stream and for the large values of viscoelastic parameter the temperature as well as the concentration profile both decreases.

• 한국해양공학회지
• /
• 제26권3호
• /
• pp.61-65
• /
• 2012

Air-water flow measurements are of importance for the coastal and ocean engineering fields. Although kinematic investigations of the multi-phase flows have been conducted for long time, velocity measurements still are concerned with many researchers and engineers in coastal and ocean areas. In the present study, an imaging technique using shadowgraphy and fiber optic probe for velocity measurements of air bubbles is introduced. The shadow graphy image technique is modified from the typical image velocimetry methods, and optical fibers are used for the well-known intrusive coupled phase-detection probe system. Since the imaging technique is a non-intrusive optical method from the air, it is usually applied for 2D flows. On the other hand, the double fiber optic probes touch flows regardless of flow patterns. The results of the flow measurements by both methods are compared and discussed. The methods are also applied to the measurements of overtopping flows by a breaking wave over the structure fixed on the free surface.

• 대한조선학회논문집
• /
• 제37권2호
• /
• pp.38-45
• /
• 2000

본 연구는 PIV 기법을 사용하여 쇄파와 몰수체의 상호작용에 의한 점성유동장의 변화를 가시화 함과 아울러 순간유동장을 해석하는데 목적을 두고 수행하였다. 몰수깊이의 변화에 따른 쇄파와 실린더의 상호작용은 S/D=1.5 정도에서 부터 감지되기 시작하여 몰수깊이가 얕아질수록 상호작용이 크게 발생하였으며 S/D=1.0 이하가 되면 쇄파로 인한 와류가 실린더로부터 유기되는 와류를 압도하여 실린더 후방의 전반적인 와도분포를 심하게 변형시킴을 알 수 있었다. 이로부터 PIV 기법은 와도분포 해석과 같은 비정상 보오텍스 유동장의 해석에 매우 유용한 방법임을 확인하였다.