• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1998.04a
• /
• pp.301-308
• /
• 1998

This paper deals with the influence of elastic foundations on natural frequencies of curved beams. Taking into account the effects of rotatoy inertia and shear deformation, the differential equations governing free, out-of-plane vibrations of circular curved beams resting on Winkler-type foundations are derived and solved numerically. Hinged-hinged, hinged-clamped and clamped-clamped end constraints are considered in numerical examples. The lowest three natural frequencies are claculated over a range of non-dimensional system parameters: the horizontal rise to span length ratio, the slenderness ratio, the foundation parameter, and the width ratio of contact area between the beam and foundation. The effects of rotatory inertia and shear deformation are also analyzed.

• 한국가시화정보학회:학술대회논문집
• /
• 2002.11a
• /
• pp.81-84
• /
• 2002

Dispersion of coolant jets in a film cooling flow field is the result of a highly complex interaction between the film cooling jets and the mainstream. In order to investigate the effect of blowing ratios on the film cooling of turbine blade, cylindrical body model was used. Mainstream Reynolds number based on the cylinder diameter was $7.1\;\times\;10^4$. The free-stream turbulence intensity kept at $5.0\%$ by using turbulence grid. The effect of coolant flow rates was studied for blowing ratios of 0.9, 1.3 and 1.6, respectively. The temperature distribution of the cylindrical model surface is visualized by infrared thermography (IRT). Results show that the film-cooling performance may be significantly improved by controlling the blowing ratio. As blowing ratio increases, the adiabatic film cooling effectiveness is more broadly distributed and the area protected by coolant increases. The mass flow rate of the coolant through the first-row holes is less than that through the second-row holes due to the pressure variation around the cylinder surface.

• Advances in nano research
• /
• v.12 no.6
• /
• pp.567-581
• /
• 2022

The free and forced vibration in addition to electric energy harvesting of a piezoelectric disk resting on two-parameter foundation modeled by modified couple stress as well as Kirchhoff plate theory is probed. The governing equations and boundary conditions are obtained using Hamilton's principle. Then, the free and forced vibration are solved using numerical solutions, generalized differential quadrature method (GDQM) and Newmark-beta method. The forced vibration is resulted from a base excitation load. Also, the possible voltage which can be harvested from this system is obtained using generalized integral quadrature method. The validity of the formulation and solution procedure is confirmed using a compassion study. The impact of parameters such as length effect, inner to outer radius ratio, and foundations parameters on the free and forced vibration as well as energy harvesting is investigated in detail. This paper can be a basis for future studies in the area of piezoelectric harvesters in small scales.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.4
• /
• pp.342-348
• /
• 2017

In this paper, film cooling characteristics at supersonic free stream conditions were examined experimentally by applying an IR-thermography. Film cooling experiments were carried out in a free-jet facility at Mach number of 3.0 and with unit Reynolds number of $42.53{\times}10^6$ and $69.35{\times}10^6$ using wedge shaped film cooling model which has a converging film cooling nozzle. Film cooling efficiency was calculated by measuring the surface temperature of PEEK(Polyether Ether Ketone) and the effects of angle of attack and blowing ratios on the film cooling efficiency were examined. The measured wall temperature was significantly reduced by the film cooling flow compared with the results without the film cooling flow. The usefulness of film cooling was also confirmed by the surface heat flux calculated using the surface temperature history of PEEK. As the blowing ratio increases the protected area of PEEK was also expanded along the direction of free stream and film cooling flow.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.2
• /
• pp.98-107
• /
• 2013

This work describes a 13b 100 MS/s 0.13 um CMOS four-stage pipeline ADC for 3G communication systems. The proposed SHA-free ADC employs a range-scaling technique based on switched-capacitor circuits to properly handle a wide input range of $2V_{P-P}$ using a single on-chip reference of $1V_{P-P}$. The proposed range scaling makes the reference buffers keep a sufficient voltage headroom and doubles the offset tolerance of a latched comparator in the flash ADC1 with a doubled input range. A two-step reference selection technique in the back-end 5b flash ADC reduces both power dissipation and chip area by 50%. The prototype ADC in a 0.13 um CMOS demonstrates the measured differential and integral nonlinearities within 0.57 LSB and 0.99 LSB, respectively. The ADC shows a maximum signal-to-noise-and-distortion ratio of 64.6 dB and a maximum spurious-free dynamic range of 74.0 dB at 100 MS/s, respectively. The ADC with an active die area of 1.2 $mm^2$ consumes 145.6 mW including high-speed reference buffers and 91 mW excluding buffers at 100 MS/s and a 1.3 V supply voltage.

• Applied Science and Convergence Technology
• /
• v.26 no.4
• /
• pp.79-85
• /
• 2017

The crack-free AlGaN template has been successfully grown by using selective area growth with triangular GaN facet. The triangular GaN stripe structure was obtained by vertical growth rate enhanced mode with low growth temperature of $950^{\circ}C$ and high growth pressure of 500 torr. The lateral growth rate enhanced mode of AlGaN for crack-free and flat surface was also investigated. Low pressure of 30 torr and high V/III ratio of 4400 were favorable for lateral growth of AlGaN. It was confirmed that the $4{\mu}m$ -thick $Al_{0.2}Ga_{0.8}N$ was crack-free over entire 2-inch wafer. The dislocation density of $Al_{0.2}Ga_{0.8}N$ was as low as ${\sim}7.6{\times}10^8/cm^2$ measured by cathodoluminescence. Based on the high quality AlGaN with low dislocation density, the ultraviolet laser diode epitaxy with cladding, waveguide and GaN/AlGaN multiple quantum well (MQW) was grown by metalorganic chemical vapor deposition. The stimulated emission at 349 nm with full width at half maximum of 1.8 nm from the MQW was observed through optical pumping experiment with 193 nm KrF laser. We also have fabricated the deep ridge type ultraviolet laser diode (UV-LD) with $5{\mu}m-wide$ and $700{\mu}m-long$ cavity for electrical properties. The turn on voltage was below 5 V and the resistance was ${\sim}55{\Omega}$ at applied voltage of 10 V. The amplified spontaneous emission spectrum of UV-LD was also observed from pulsed current injection.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.298-303
• /
• 2018

This study discusses the conceptual definition of a balcony and the emergence of basic-type and expansion-type floor plans according to the balcony utilization. In addition, the change in building density is analyzed with regard to real cases, and base data are offered for future urban policies in Incheon Metropolitan City. The context of the Building Acts could be understood through the analysis of various balcony definitions and characteristics, and the analysis was divided into basic and extension types according to the legalization that occurred in 2005. The issue of density according to balcony expansion is discussed through theories, and a planned attempt at density management in the target area is investigated. The building area, floor area, and floor area ratio are discussed with regard to the target area, and the density management is empirically proven, which is different from the Unit Plan.

• Wind and Structures
• /
• v.17 no.5
• /
• pp.537-552
• /
• 2013

Wind tunnel experiments were performed to study the wind loads on an inclined flat plate with and without a guide plate. Highly turbulent flow, which corresponded to free-stream turbulence intensity on the flat roof of low-rise buildings, was produced by a turbulence generation grid at the inlet of the test section. The test model could represent a typical solar collector panel of a solar water heater. There are up-stream movements of the separation bubble and side-edge vortices, more intense fluctuating pressure and a higher bending moment in the turbulent flow. A guide plate would result in higher lift coefficient, particularly with an increased projected area ratio of a guide plate to an inclined flat plate. The value of lift coefficient is considerably lower with increased free-stream turbulent intensity.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.11 no.1
• /
• pp.1-8
• /
• 1974

Hydrodynamic forces and moments produced by the swaying oscillation on the free surface were exactly calculated by Ursell-Tasai method for the cylinders with Kim's chine form sections and the sway responses of the cylinders of those chine form sections among the regular beam sea were also calculated. The results of the computation were compared with those of Lewis form sections. It is concluded that the effects of the section form on the added mass, and damping are small, if the section forms had same beam-draft ratio and sectional area coefficient in the case of sway motion. It is also known that the above little effects of section shapes on the basic hydrodynamic forces do not effect on the sway motion responses of cylinderical bodies among the regular beam sea. The sway motion responses of cylinderical bodies are varied linearly with the wave numbers.

• Korean Journal of Agricultural Science
• /
• v.25 no.2
• /
• pp.293-309
• /
• 1998

This study is aimed at identifying the decision making criteria as B/C ratio, IRR and NPV based on the expected benefits and costs of the land utilization and promotion projects which have implemented to improve agricultural structure under WTO system. To carry out the objectives of the study, Sinseok project area located at Dangjin district, Chungnam province was selected. Sinseok project area has 306.2 ha of paddy area with 172 farm households. The project area will be operated by the 33 specialized farm households after completion of the project which will have 20 years of economic life. After completion of the project, farm size will be increased from 1.8ha to 9.3ha. Land intensity of the project area will be increased by 10%. Increase of land productivity and cost saving due to the labor saving technology as farm mechanization will be expected. According to the survey results, the annual amount of production cost savings per farm was estimated 3.884million won and increased total farm income was expected about 43.8million won per year. The total expexted project benefits was expected 174million won per year. The project costs to promote land utilization and structural change consisted of handling charges, and direct payment for land movility. The decision making criteria representing economic feasibility of the project such as B/C ratio, NPV and IRR were estimated 2.49, 483million won and 30% respectively when the cut-off rate was taken into account 10%. In conclusion, the land utilization and promotion project proppeled by the Korean Government under the agricultural land law is considered economically feasible from the view points of expected project benefits and costs. Accordingly the project have to be implemented more strongly under the G't financial support considering WTO and UR negociation which were aimed at achieving the free trade and improvement of international competitiveness of farm products.