• 콘크리트학회논문집
• /
• 제17권5호
• /
• pp.727-734
• /
• 2005

최근 증가하고 있는 초고층 주거용 구조물 중 많은 수가 건축적인 이유로 인해 건물골조시스템을 주요 지진저항시스템으로 채택하고 있다. 그러나 KBC 2005를 적용하여 건물골조시스템을 설계할 때 기준에서 언급되지 않거나 모호한 표현으로 인해 설계자는 많은 어려움을 겪을 수 있다. 특히 정적$\cdot$동적 해석시 RC부재의 균열단면을 고려한 유효강성의 적용 방법, 변형 적합성을 고려한 골조의 설계법 등에서 어려움을 겪을 수 있다. 이에 대하여 전단벽과 골조(플랫 플레이트)로 이루어진 전형적인 건물골조시스템의 건물에 대해 KBC 2005를 적용하고 기준의 불명확한 부분에 대해서 여러 방법을 적용하여 해석한 결과 기준의 모호한 언급이나 설계자의 임의의 판단으로 인해 층간변위비, 전단벽 및 연결보의 요구강도 등에서 매우 큰 차이가 발생하였으며, 동일한 건물을 이중골조시스템으로 설계한 경우에 비해 건물골조시스템으로 설계한 경우 변형 적합성의 요구로 인해 전단벽의 높은 요구강도 뿐만 아니라 골조에서도 높은 연성이 요구되었다.

• Nuclear Engineering and Technology
• /
• 제31권6호
• /
• pp.586-594
• /
• 1999

To limit both the large displacement and acceleration response of the structure efficiently, the relationships between acceleration and displacement responses of the structure under several earthquakes are investigated for various horizontal stiffness of the base isolation system to determine the effective stiffness of the base isolation system in this paper. An example structure is a five-storey steel frame building as the primary structure and the secondary structures are assumed to be located on the fifth floor of the primary structure. Input motions used in the structural analysis are El Centre 1940, Taft 1952, Mexico 1985, San Fernando 1971 Pacoima Dam, and artificially generated earthquakes. The relationships of the absolute peak acceleration and the displacement at the top of the structure are calculated for various natural periods of base isolators under various earthquakes. The peak acceleration response of the fifth floor in the base isolated structure is significantly reduced by a factor of 2.1 through 6.25. Also, the relative displacement response of the floor to the base of the superstructure is very small. The results of this study can be utilized to determine the effective stiffness of the base isolation system.

• 한국자동차공학회논문집
• /
• 제10권1호
• /
• pp.216-233
• /
• 2002

Due to the environmental problems of fuel consumption and vehicle emission, etc., automotive makers are trying to reduce the weight of vehicles. The most effective way to reduce a vehicle weight is to use lighter materials, such as aluminum and plastics. Aluminum Intensive Vehicle(AIV) has many advantages in the aspects of weight reduction, body stiffness and model change. So, most of automotive manufacturers are attempting to develop AIV using Aluminum Space Frame(ASF). The weight of AIV can be generally reduced to about 30% than that of conventional steel vehicle without the loss of impact energy absorbing capability. And the body stiffness of AIV is higher than that of conventional steel monocoque body. In this study, Aluminum Intensive Vehicle is developed and analyzed on the basis of steel monocoque body. The energy absorbing characteristics of aluminum extrusion components are investigated from the test and simulation results. The crush and crash characteristics of AIV based on the FMVSS 208 regulations are evaluated in comparison with steel monocoque. Using these results, the design concepts of the effective energy absorbing members and the design guide line to improve crashworthiness for AIV are suggested.

• Structural Engineering and Mechanics
• /
• 제35권1호
• /
• pp.19-35
• /
• 2010

This paper proposes a hybrid heuristic and criteria-based method of optimum design which combines the advantages of both the iterated simulated annealing (SA) algorithm and the rigorously derived optimality criteria (OC) for structural optimum design of reinforced concrete (RC) buildings under multi-load cases based on the current Chinese design codes. The entire optimum design procedure is divided into two parts: strength optimum design and stiffness optimum design. A modified SA with the strategy of adaptive feasible region is proposed to perform the discrete optimization of RC frame structures under the strength constraints. The optimum stiffness design is conducted using OC method with the optimum results of strength optimum design as the lower bounds of member size. The proposed method is integrated into the commercial software packages for building structural design, SATWE, and for finite element analysis, ANSYS, for practical applications. Finally, two practical frame-shear-wall structures (15-story and 30-story) are optimized to illustrate the effectiveness and practicality of the proposed optimum design method.

• 한국지진공학회논문집
• /
• 제22권5호
• /
• pp.299-309
• /
• 2018

Now that problems with force-based seismic design have been clearly identified, design is inclined toward displacement-based methods. One such widely used method is Direct-Displacement-Based Design (DDBD). Yet, one of the shortcomings of DDBD is considering higher-mode amplification of story shear, moments, and displacements using equations obtained from limited parametric studies of regular planar frames. In this paper, a different approach to account for higher-mode effects is proposed. This approach determines the lateral secant stiffness of the building frames that fulfill the allowable inter-story drift without exceeding the desired story displacements. Using the stiffness, an elastic response spectrum analysis is carried out to determine elastic higher-mode force effects. These force effects are then combined with DDBD-obtained first-mode force effects using the appropriate modal superposition method so that design can be performed. The proposed design procedure is verified using Nonlinear Time History Analysis (NTHA) of twelve planar frames in four categories accounting for mass and stiffness irregularity along the height. In general, the NTHA response outputs compared well with the allowable limits of the performance objective. Thus, it fulfills the aim of minimizing the use of NTHA for planar frame buildings, thereby saving computational resources and effort.

• Structural Engineering and Mechanics
• /
• 제67권3호
• /
• pp.233-244
• /
• 2018

This study aims at evaluating the performance of repairing technique with CFRPs in recovering cyclic performance of damaged columns in flexure in terms of structural response parameters such as strength, dissipated energy, stiffness degradation. A 2/3 scaled substandard reinforced concrete frame was constructed to represent the substandard RC buildings especially in developing countries. These substandard buildings have several structural deficiencies such as strong beam-weak column phenomenon, improper reinforcement detailing and poor material properties. Flexural plastic hinges occurred at the columns ends after testing the substandard specimen under both constant axial load and reversed cyclic lateral loading. Afterwards, the damaged columns were externally wrapped with CFRP sheets both in transverse and longitudinal directions and then retested under the same loading protocol. In addition, ambient vibration measurements were taken from the undamaged, damaged and the repaired specimens at each structural repair steps to identify the effectiveness of each repairing step by monitoring the change in the natural frequencies of the tested specimen. The ambient vibration test results showed that the applied repairing technique with external CFRP wrapping was proved to recover stiffness of the pre-damaged specimen. Moreover, the lateral load capacity of the pre-damaged substandard RC frame was restored with externally bonded CFRP sheets.

• 전산구조공학
• /
• 제4권1호
• /
• pp.83-94
• /
• 1991

본 연구에서는 이상화구조요소법을 적용하여 골조구조물의 비선형해석을 높은정도로서 짧은 계산시간에 수행할 수 있는 해석이론과 컴퓨터프로그램을 개발하였다. 이를 위해 골조구조물을 구성하는 보-기둥(Beam-Column)부재에 대한 이상화구조요소를 부재에 존재하는 초기결함의 영향도 고려하여 정식화한다. 요소의 접선탄성강성행렬은 에너지원리를 적용하여 명시적인 형태로 도출하며, 최종강도조건은 요소에 소성붕괴메카니즘이 형성될때를 기준으로 정식화한다. 또한, 요소의 최종강도후 강성행렬도 근사적인 방법을 이용하여 명시적인 형태로 도출한다. 본해석법의 정도와 유용성은 단위부재 및 골조구조모형에 대한 기존의 실험 및 수치해석결과등과 비교하여 확인한다.

• Structural Engineering and Mechanics
• /
• 제85권6호
• /
• pp.825-835
• /
• 2023

The effective buckling length factor is an important parameter in the elastic buckling analysis of steel structures. The present article aims at developing a new method that allows the determination of the buckling factor values for frames. The novelty of the method is that it considers the interaction between the bracing and the elastic supports for asymmetrical frames in particular. The approach consists in isolating a critical column within the frame and evaluating the rotational and translational stiffness of its restraints to obtain the critical buckling load. This can be achieved by introducing, through a dimensionless parameter 𝜙_i, the effects of coupling between the axial loading and bending stiffness of the columns, on the classical stability functions. Subsequently, comparative, and parametric studies conducted on several frames are presented for assessing the influence of geometry, loading, bracing, and support conditions of the frame columns on the value of the effective buckling length factor K. The results show that the formulas recommended by different approaches can give rather inaccurate values of K, especially in the case of asymmetric frames. The expressions used refer solely to local stiffness distributions, and not to the overall behavior of the structure.

• Steel and Composite Structures
• /
• 제47권2호
• /
• pp.185-201
• /
• 2023

Despite the high lateral stiffness and strength of the Concentrically Braced Frame (CBF), due to the buckling of its diagonal members, it is not a suitable system in high seismic regions. Among the offered methods to overcome the shortcoming, utilizing a metallic damper is considered as an appropriate idea to enhance the behavior of Concentrically Braced Frames (CBFs). Therefore, in this paper, an innovative steel damper is proposed, which is investigated experimentally and numerically. Moreover, a parametrical study was carried out to evaluate the effect of the mechanism (shear, shear-flexural, and flexural) considering buckling mode (elastic, inelastic, and plastic) on the behavior of the damper. Besides, the necessary formulas based on the parametrical study were presented to predict the behavior of the damper that they showed good agreement with finite element (FE) results. Both experimental and numerical results confirmed that dampers with the shear mechanism in all buckling modes have a better performance than other dampers. Accordingly, the FE results indicated that the shear damper has greater ultimate strength than the flexural damper by 32%, 31%, and 56%, respectively, for plates with elastic, inelastic, and plastic buckling modes. Also, the shear damper has a greater stiffness than the flexural damper by 43%, 26%, and 53%, respectively, for dampers with elastic, inelastic, and plastic buckling modes.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.105-112
• /
• 2005

Recently, Various structural systems for skyscrapers are studied as structures are more higher. The mega frame system of all, which is the structural system developed recently, are considered as a suitable structural system for skyscrapers. This structural system has sufficient stiffness for the lateral forces with mega-columns which consist of many columns and mega-girders which consist of girders with large stiffness or trusses. But there is no efficient analysis method and a design method for it. Therefore, an efficient analytical model, which has only DOFs selected by the user using the matrix condensation technique, is proposed in this study to obtain accurate results in significantly reduced computational time.