• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.3
• /
• pp.198-208
• /
• 1997

The-steady-state creep mechanism and behavior of Zircaloy-4 used as cladding materials in PWR have been investigated in air environment over the temp, ranges from 600 to $645^{\circ}C$ and stress ranges from 4 to $7kg/mm^2$. The stress exponents for the creep deformation of this alloy, n were decreased 4.81, 4.71, 4.64, and 4.56 at 600, 615, 630 and $645^{\circ}C$, respectively; the stress exponents decreased with increasing the temperature and got closer to about 5. The apparent activation energies, Q, were 62.1, 60.0, 57.9 and 55.4 kcal/mole at stresses of 4, 5, 6, $7kg/mm^2$, respectively; the activation energies decreased with increasing the stress and were close to those of volume self diffusion of Zr in Zr-Sn-Fe-Cr system. In results, it can be considered that the creep deformation for Zircaloy-4 was controlled by the dislocation climb over the ranges of this experimental conditions. Larson-Miller parameter, P, for the crept specimens was obtained as P=(T+460)(logt,+23). The failure plane observed by SEM slightly showed up intergranular fracture at this experiment ranges. However, it was essentially dominated by the dimple phenomenon, which was a characteristics of the transgranular fracture.

• Clinics in Shoulder and Elbow
• /
• v.24 no.1
• /
• pp.42-52
• /
• 2021

Reverse shoulder arthroplasty is an ideal treatment for glenohumeral dysfunction due to cuff tear arthropathy. As the number of patients treated with reverse shoulder arthroplasty is increasing, the incidence of complications after this procedure also is increasing. The rate of complications in reverse shoulder arthroplasty was reported to be 15%-24%. Recently, the following complications have been reported in order of frequency: periprosthetic infection, dislocation, periprosthetic fracture, neurologic injury, scapular notching, acromion or scapular spine fracture, and aseptic loosening of prosthesis. However, the overall complication rate has varied across studies because of different prosthesis used, improvement of implant and surgical skills, and different definitions of complications. Some authors included complications that affect the clinical outcomes of the surgery, while others reported minor complications that do not affect the clinical outcomes such as minor reversible neurologic deficit or minimal scapular notching. This review article summarizes the processes related to diagnosis and treatment of complications after reverse shoulder arthroplasty with the aim of helping clinicians reduce complications and perform appropriate procedures if/when complications occur.

• Journal of the Korean Orthopaedic Association
• /
• v.56 no.1
• /
• pp.51-60
• /
• 2021

Purpose: Radiocarpal dislocation (RCD), which is caused by high-energy trauma, often involves radial styloid fractures and short radiolunate ligament (SRLL) injuries. Although SRLL injuries may occur as a simple rupture at the attachment site of radius, it may occur with a relatively large avulsed-fragment in the volar rim of the lunate facet of the radius. This study aimed to differentiate the injury type of SRLL and assess the differences in the treatment results depending on the treatment methods that have been applied in RCD with radial styloid fractures. Materials and Methods: Eighteen patients managed surgically with RCD were enrolled in this study. The patients were classified as Group 1 and Group 2 by using the Dumontier method. In this study, Group 2 was subdivided into 2A (purely ligamentous or small avulsion fracture of the volar rim of lunate facet) and 2B (large avulsed-fragment enough to internal fixation) according to the injury type of SRLL. Groups 2A and 2B were treated with direct repair and screw fixation, respectively. Pain, range of motion of the wrist joint, grip strength, and complications on final radiographs were examined. The outcomes were evaluated using patient-rated wrist evaluation (PRWE), and modified Mayo wrist score (MMWS). Results: All patients were Group 2 (six and twelve patients in 2A and 2B, respectively). The mean flexion to extension arch recovered 79%,and the mean grip strength was 72.9% of the uninjured side. Group 2A showed better recovery in extension, flexion and pronation than Group 2B, but there was no difference in radial deviation, ulnar deviation, supination, grip strength and pain. No differences in the PRWE and MMWS were observed between two groups. Complications included traumatic arthritis in seven patients and residual instability in five patients. Conclusion: When the SRLL was injured, the involvement of a large avulsion fracture on the anterior plane of the radiolunate did not affect the test results. On the other hand, it should be observed cautiously because avulsion fractures tend to disturb the joint's reduction through rotation or displacement. In addition, anatomical reduction and sturdy internal fixation are important for restoring the function of the SRLL.

• Journal of Chest Surgery
• /
• v.12 no.4
• /
• pp.418-423
• /
• 1979

Chest injuries due to blunt trauma often result in severe derangements that lead to death. And we have to diagnose and treat the patients who have blunt chest trauma immediately and appropriately. A clinical analysis was made on 324 cases of chest injury due to blunt trauma experienced at department of Thoracic and Cardiovascular Surgery, College of Medicine, Kyung Hee University during 8-year period from 1972 to 1979. Of 324 patients of blunt chest injuries, there were 189 cases of rib fracture, 121 of hemothorax or/and pneumothorax, 108 of soft tissue injury of the chest wall only, 41 of lung contusion, 24 of flail chest, 13 of scapular fracture, 7 of diaphragmatic rupture and others. The majority of blunt chest injury patients were traffic accident victims and falls accounted for the next largest group of accidents. Chest injuries were frequently encountered in the age group between 3rd decade and 4th decade [60%] and 238 patients were male comparing to 86 of female [Male: Female = 3:1 ]. In the patients who have the more number of fractured ribs, the more incidence of intrathoracic injury and intraabdominal organ damage were found. The principal associated injuries were head injury on 58 cases, long bone fractures on 37, skull fractures on 12, pelvic fractures on 10, renal injuries on 6 and intraabdominal organ injuries on 5 patients. The principle of early treatment of chest injury due to blunt trauma were rapid reexpansion of the lung by closed thoracotomy which was indicated on 96 cases, but open thoractomy was necessary on 14 cases because massive bleeding, intrapleural hematoma and/or fibrothorax, or diaphragmatic laceration-On 15 cases who were young and have multiple rib fracture with severe dislocation delayed elective open reduction of the fractured ribs with wire was done on the purpose of preserving normal active life. The over all mortality was 2.8% [9 of 324 cases] due to head injury on 3 cases, massive bleeding on 2,wet lung syndrome, acute renal failure on 1 and septicemia on 1 patient.

• Clinics in Shoulder and Elbow
• /
• v.14 no.1
• /
• pp.146-152
• /
• 2011

Purpose: To describe the recent clinical results and complications of total elbow arthroplasty based on the literature review. Materials and Methods: The indications of total elbow arthroplasty include rheumatoid or inflammatory arthritis, posttraumatic arthritis, anklylosed elbow, tumor resection which cannot recover elbow function by other reconstructive procedures, and comminuted distal humerus fracture in elderly patients. Complications are aspetic loosening, infection, prosthesis fracture, periprosthetic fracture, ulnar neuropathy, ectopic ossification, triceps insufficiency, dislocation, and bushing wear. Results and Conclusion: Mean 10 year survival rate following total elbow arthroplasty has been reported 85% on the basis of revision. The prognosis in patients with an inflammatory arthritis is reported to be best, and loosening rate in patients with a posttraumatic arthritis tends to be high. Complication rate is known to be higher than that of other joint arthroplasty. In particular, deep infection occurs in 3~5% of the patients. Total elbow arthroplasty provide satisfactory results when it is performed properly in selected patients who have an elbow joint with irreversible dysfunction and low level activities.

• Hip & pelvis
• /
• v.35 no.2
• /
• pp.99-107
• /
• 2023

Purpose: Bipolar hemiarthroplasty has recently been acknowledged as an effective option for treatment of unstable intertrochanteric fracture. Trochanteric fragment nonunion can cause postoperative weakness of the abductor muscle and dislocation; therefore, reduction and fixation of the fragment is essential. The purpose of this study was to perform an evaluation and analysis of the outcomes of bipolar hemiarthroplasty using a useful wiring technique for management of unstable intertrochanteric fractures. Materials and Methods: A total of 217 patients who underwent bipolar hemiarthroplasty using a cementless stem and a wiring technique for management of unstable intertrochanteric femoral fractures (AO/OTA classification 31-A2) at our hospital from January 2017 to December 2020 were included in this study. Evaluation of clinical outcomes was performed using the Harris hip score (HHS) and the ambulatory capacity reported by patients was classified according to Koval stage at six months postoperatively. Evaluation of radiologic outcomes for subsidence, breakage of wiring, and loosening was also performed using plain radiographs at six months postoperatively. Results: Among 217 patients, five patients died during the follow-up period as a result of problems unrelated to the operation. The mean HHS was 75±12 and the mean Koval category before the injury was 2.5±1.8. A broken wire was detected around the greater trochanter and lesser trochanter in 25 patients (11.5%). The mean distance of stem subsidence was 2.2±1.7 mm. Conclusion: Our wiring fixation technique can be regarded as an effective additional surgical option for fixation of trochanteric fracture fragments during performance of bipolar hemiarthroplasty.

• Korean Journal of Materials Research
• /
• v.14 no.1
• /
• pp.19-27
• /
• 2004

Metallurgical and mechanical experiments were performed to explain unexpected surface cracks encountered in fabricating ground rolled-billet of Fe-Cr-Al alloys at room temperature. The toughness of these alloys containing between 220 and 236 ppm (C+N) has been assessed using notched-bar impact tests. According to our results, with a larger grain size, a higher interstitial content of (C+N) or a smaller size of precipitates, ductile to brittle temperature(DBTT) increased and absorbed energy decreased at room temperature. These results suggest that the surface cracks at room temperature stem from a poor resistance to brittle fracture, due to dislocation movement by the finely dispersed carbides within grains under the condition of higher (C+N) content.

• Journal of the Korean Society for Heat Treatment
• /
• v.7 no.4
• /
• pp.277-287
• /
• 1994

The effect of grain size on the tensile properties and fatigue behavior of austenitic high Mn steel has been investigated. The recrystallized austenite grain size of the cold rolled high Mn steel was increased as the annealing temperature increased from $600^{\circ}C$ to $1000^{\circ}C$. Larger austenite grain size decreased the yield strength and the tensile strength, and increased the uniform elongation due to transformation of some austenite into twins or E-martensite phase during deformation. Austenite grain refinement increased the tendency to form dislocation cells, instead. The specimen annealed at $1000^{\circ}C$ with large grain size showed lower fatigue crack propagation rate in low ${\Delta}K$ region due to rougher fracture surface caused by formation of deformation twins during fatigue at the crack tip region.

• Structural Engineering and Mechanics
• /
• v.34 no.3
• /
• pp.377-390
• /
• 2010

This paper studies fracture initiation direction of two parallel non-coplanar cracks of equal length. Using the dislocation pile-up modelling, singular integral equations for two parallel cracks subjected to mixed-mode loading are derived and the crack-tip field including singular and non-singular terms is obtained. The kinking angle is determined by using the maximum hoop stress criterion, or the ${\sigma}_{\theta}$-criterion. Results are presented for simple uniaxial tension and biaxial loading. The biaxiality ratio has a noticeable influence on crack growth direction. For the case of biaxial tension, when neglecting the T-stress the crack branching angle is overestimated for small crack inclination angles relative to the largest applied principal stress direction, and underestimated for large crack inclination angles.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.4 s.235
• /
• pp.632-638
• /
• 2005

The surface lapping process on sapphire wafer was carried out for the epitaxial process of thin film growth of GaN semiconducting material. The planarization of the wafers was investigated by the introduction of the dummy wafers. The diamond lapping process causes the surface deformation of dislocation and micro-cracks. The material deformation due to the mechanical stress was analyzed by the X-ray diffraction and the Vickers indentation. The fracture toughness was increased with the increased annealing temperature indicating the recrystallization at the surface of the sapphire wafer The sudden increase at the temperature of $1200^{\circ}C$ was correlated with the surface phase transition of sapphire from a $-A1_{2}O_{3}\;to\;{\beta}-A1_{2}O_{3}$.