• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2004.05b
• /
• pp.472-474
• /
• 2004

In this study, we investigated the characteristics of the input impedance and the gain of a ‘Folded dipole antenna with stub’ by the Method of Moments. The center frequency in this study is 200MHz, the radius of wire is 0.5nm, and the distance between two linear dipoles is 2cm. The inside variation of stub length within 18cm and the outside variation of stub length 4.5cm ive the value of SWR(Standing Wave Ratio) within 3. This means that the impedance matching between the ‘Folded dipole antenna with stub’ and receiver can easily be performed without a supplementary matching circuit.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.12
• /
• pp.1327-1336
• /
• 2007

In this paper, we propose a reconfigurable antenna which operates as a disk-loaded dipole antenna and a folded dipole antenna alternatively using RF on/off switches. The antenna can change its effective length to achieve dual-band operation; operates as the folded dipole antenna for stepping up the radiation resistance in low frequency band of $20{\sim}300$ MHz, and as the disk-loaded dipole antenna for an omni-directional radiation pattern (horizontal plane) and a donut-shaped radiation pattern (vertical plane) in high frequency band of $300{\sim}1.3$ GHz. In the low band, the proposed antenna shows higher gain than a conventional dipole antenna with a reduced antenna size. In the high band, the antenna maintains a broad beamwidth of about $80^{\circ}$, thus the antenna can be applicable to antennas for direction finding applications.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.2
• /
• pp.267-272
• /
• 1999

In general, printed antennas have a narrow bandwidth characteristic and many people want to find out the method of bandwidth improvement through complicated procedures. So we want to reform the conventional printed antenna characteristic by using the folded dipole's superiority to unit dipole. But it is hard to feed the printed folded dipole antenna, we use the CPW, which is widely used in microwave IC or MMIC applications and have many advantages to the conventional microstrip line, to feed the printed folded slot antenna. It is confirmed that the improvement in the bandwidth characteristic of CPW fed folded slot antenna, as much as 20%, through the measurement of designed and implemented antenna.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 1999.05a
• /
• pp.301-304
• /
• 1999

In general, printed antennas have a narrow bandwidth characteristic and many people want to find out the method of bandwidth improvement through complicated procedure. So we want to reform the conventional printed antenna characteristic by using the folded dipole's superiority to unit dipole. But it is hard to feed thr printed folded dipole antenna, we use the CPW, which is widely used in microwave IC or MMIC applications and have many advantage to the conventional microstrip line, to feed the folded slot antenna. It is confirmed that the improvement in the bandwidth characteristic of CPW fed folded slot antenna, as much as 20%, through the measurment of designed and implemented antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.4
• /
• pp.261-268
• /
• 2017

In this paper, we propose an FSSH(Folded Slot Spherical Helix) magnetic dipole antenna with a form factor easy to build and study its radiation properties. The number of folded arms, the gap between them and the metal thickness are tuned to achieve relatively simple structure to realize whereas maintaining high radiation efficiency at an electrically small size. The proposed design shows wide radiation efficiency bandwidth and it is confirmed by circuit simulation that the non-Foster impedance matching techniques could be utilized for its practical use. The prototype of the proposed antenna is built with the aid of an SLS(Selective Laser Sintering) 3D printing technology. The measured result shows lower Q impedance characteristic due to high resistive loss of the copper tape joints.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.8 no.5
• /
• pp.43-49
• /
• 2008

Motivated by the Communication Broadcasting Convergence service, various technical approaches are being used to develop more efficient antenna models. This paper proposes a compact mobile antenna which is attachable to a cell phone and is applicable for Communication Broadcasting Convergence. In the design of the antennas for mobile handsets, size reduction is a crucial factor. In this paper, the compactness of a loop antenna is realized by bending a folded-dipole. A short planar dipole is transformed to a twice folded dipole and a loop antenna to produce a larger input resistance. The current distribution of the antenna is the same as a loop antenna, and its radiation patterns are omni-directional. We also analyze the performance of the RFID antenna by exploring the current-induced near field radiation patterns using a electro-optic field mapping system.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.5 no.4
• /
• pp.9-19
• /
• 1968

In this paper, I introduced the theoretical formulas for calcuating the input impedance of a folded dipole antenna which is held in parallel with the conductive supporter. Through the comparision of the above impedance formulas with the imput impedance formulas of a half wave dipole antenna which is parallel to the conductive supporter, it was found that the former can be made in identically same form as the latter, if some conditions are satisfied. The equivalent conditions mentioned above are derived also and the manufacturing of a vertically polarized omni-drectional antenna is apossible by the use of above equivalent conditions, because a half wave dipole antenna in parallel with a conductive supporter is already illustrated to become an omni-directional vertical polarization antenna. Some experimental data are shown together.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.7
• /
• pp.75-79
• /
• 2004

In this paper, a single plane wide band microstrip antenna for integrated circuit as MMIC and LTCC is designed and fabricated. A new configuration for a wide band microstrip antenna with omni-directional pattern is proposed. This antenna consists of two rectangular folded dipoles, which are fed by a coplanar waveguide(CPW). It was effected stabilization ground that a signal plane of CPW feed have been limited ground plane. Therefore, a ground plane of folded structure should be extended outside folded antenna in this research. The characteristics of the proposed antenna were analyzed by using an FDTD methods. The return loss and radiation patterns were simulated and measured. The proposed antenna is get 120MHz bandwidth of PCS band and 250MHz bandwidth of IMT2000 band, used ISM band.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.11B
• /
• pp.1612-1619
• /
• 2001

This paper examines the design, implementation characteristics of a folded dipole active integrated antenna. Our goal was to minimize the physical size of RF circuit and its insertion loss, and to make the high frequency tuning easier by directly integrating the ISM(Industrial Scientific & Medical) band power amplifier and antenna. Non-linear model has been used for highly accurate simulation of the power amplifier. The maximum power level was found by using the Load pull method before an impedance matching was achieved. It is found that the total power-added efficiency(PAE) including the driving amplifier was 31.5% and that the transmit power was 13.7 dBm. We also found that the proposed scheme with the smaller antenna as compared with the existing dipole antenna has 23.7 dB total gain including the antenna gain. The suppression of the second harmonic signal to the fundamental signal with respect to the fundamental signal was found to be more than 30 dBc.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.1
• /
• pp.8-13
• /
• 2016

A pattern-switchable origami antenna is designed with paper using inkjet-printing technology. The proposed antenna can be switched between loop and dipole antenna modes by folding and unfolding the paper, respectively. The proposed antenna is designed for the resonant frequencies of both modes to be 1.85 GHz. Eutectic gallium-indium liquid metal is introduced in order to avoid cracks in the conductive ink when the paper is folded. The performance of the proposed antenna is demonstrated through simulation and measurement results and antenna gain of dipole-mode and loop-mode are -4 dBi and -5 dBi, respectively. Also, the nulls of both dipole and loop modes compensate nulls from each mode.