• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.17-20
• /
• 2003

Step index POFs(SIPOF) are composed of core polymers and cladding polymers. Poly(methyl methacrylate) (PMMA) and polystyrene (PS) are normally used as core materials. The refractive index of cladding materials should be less than 2-5 % that of the core material. PMMA and fluorinated polymers are used as cladding materials on PS and PMMA core, respectively$^1$. Cladding materials which have lower refractive index than core materials reflect light at less than critical angle, which is transmitted down the core. (omitted)

• Journal of Aerospace System Engineering
• /
• v.2 no.3
• /
• pp.19-23
• /
• 2008

We have fabricated pressure sensitive paint films consisting of PtTFPP activators dispersed in fluorinated polymer matrix. This matrix material is unique in its composition and structure. We evaluated the oxygen quenching effects, and thus the pressure sensitivity, of the fabricated films in terms of various processing parameters. Based on the experimental results, we anticipate that a good but new pressure sensitive paint would be presented through further elaboration of the polymer compositions and optimization of the processing conditions.

• Polymer(Korea)
• /
• v.39 no.2
• /
• pp.338-345
• /
• 2015

Poly(phenylene oxide) (PPO) and polyether imide (PEI) were sulfonated and aminated to create sulfonated poly(phenylene oxide) (SPPO) and aminated polyether imide (APEI), respectively. Characterization of the SPPO and APEI were performed via measurements of FTIR, thermogravimetry (TGA), swelling degree, ion exchange capacity (IEC), and ion conductivity. Next, the surfaces of these membranes were modified by surface fluorination at room temperature. The surface fluorinated SPPO and APEI membranes underwent characterization again for the mentioned measurements to determine any differences. The 3 types of bi-polar membranes were prepared by varying the IEC of the APEI at a fixed SPPO IEC value, which were applied to the low and high NaCl concentration of feed solution at the different current density, respectively. The hypochlorite concentration derived from the surface fluorinated membranes was dependent on the IEC of the APEI and ranged from 491 to 692 ppm at $80mA/m^2$. At low current density of $5mA/m^2$, the hypochlorite concentrations ranged from 18 to 28 ppm for the 4 hrs surface fluorinated membranes and their durability increased greatly.

• Polymer(Korea)
• /
• v.33 no.6
• /
• pp.537-543
• /
• 2009

The direct fluorination of polymers is a heterogeneous reaction using the mixture of $F_2$ and inert gas. In general, the resulting fluorinated polymers have good barrier property chemical stability similar to those of the fluoro-polymers, and could be prepared from the simple process. In this study, the polysulfone dense films were surface fluorinated using the direct fluorination technique and gas permeability and selectivity of the prepared membranes were measured with varying both $F_2$ concentration and reaction time. The introduction of $F_2$ was confirmed by X-ray photoelectron spectroscopy (XPS), water contact angles, and atomic force microscopy (AFM). As the $F_2$ increased, the permeability decreased while the selectivities for $O_2$, $CO_2$, and He gases relative to $N_2$ increased.

• Applied Chemistry for Engineering
• /
• v.22 no.5
• /
• pp.467-472
• /
• 2011

This study investigated illite/polypropylene (PP) composite filament formation via melt-spinning and evaluated their physical properties to prepare functional fibers using natural materials. When composite filaments were formed, the composite filaments exhibited smaller fiber diameters compared to that of neat PP filament because of the lubricant effect of illite induced by its layered structure. Moreover, fluorination effect increased interfacial affinity and dispersion in the polymer, resulting in smaller diameter of fluorinated illite/PP composite filament, which was 2/3 of the neat PP filament diameter. Addition of raw and fluorinated illite improved thermal stability of illite/PP composite filament. Raw illite/PP composite filament cannot be used for a practical application, because it broke during drawing process, whereas the fluorinated illite/PP composite filament can be used for a practical application, because it exhibited similar tensile strength of the neat PP filament and 50% increased modulus. Even with improved illite/PP interfacial affinity and illite dispersion in the polymer, illite/PP composite filament formed microcomposite, because non-expandable illite had strongly bound layers, resulting in only a little illite exfoliation and PP intercalation into illite.

• Journal of Environmental Health Sciences
• /
• v.38 no.6
• /
• pp.451-459
• /
• 2012

Background: In Korea, a healthy 36-year-old man developed acute interstitial pneumonitis soon after inhaling a waterproofing spray which he had applied at home to his outdoor jacket. Objectives: The objectives of this study were to review cases of varying degrees of respiratory toxicity and poisoning in connection with the use of waterproofing spray and summarize major reasons for cases of poisoning. Methods: We searched articles reporting on a combination of a waterproofing agent and/or respiratory symptoms, including acute respiratory syndrome, lung injury, pneumonia, pulmonary toxicity, and respiratory disease. Results: We reviewed a number of cases of varying degrees of respiratory toxicity and poisoning resulting from inhalation of waterproofing spray containing fluorocarbon co-polymer, solvents and propellants reported in a variety of countries. The literature searches concluded that among the ingredients of waterproofing agents, fluorinated polymer may cause acute respiratory health effects. Conclusion: Environmental policy should be implemented in order to prevent consumers from using household and industrial products including waterproofing agents. In addition, a national surveillance system should be created to collect cases of poisoning caused by the use of consumer products.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.75.2-75.2
• /
• 2010

Polymer electrolyte fuel cells (PEFCs) have received a lot of attention as a power source for both stationary and mobile applications due to their attractive feature. In general, the performance of PEFCs is highly affected by the property of the electrodes. A PEFC electrode essentially consists of a gas diffusion layer and a catalyst layer. The gas difusion layer is highly porous and hydrophobicized with PTFE polymer. The catalyst layer usually contains electrocatalyst, proton conducting polymer, even PTFE as additive. Particularly, the proton conducting ionomer helps to increase the catalytic activity at three-phase boundary and catalyst utilization. Futhermore, it helps to retain moisture, resulting in preventing the electrodes from membrane dehydration. The most widely used proton conducting ionomer is perfluorinated sulfonic acid polymer, namely, Nafion from DuPont due to its high proton conductivity and good mechanical property. However, there are great demands for alternative ionomers based on non-fluorinated materials in terms of high temperature availability, environmental adaptability and production cost. In this study, the electrodes with the various content of the sulfonated poly(ether sulfone) ionomer in the catalyst layer were prepared. In addition, we evaluated electrochemical properties of the prepared electrodes containing the various amount of the ionomers by using the cyclic voltammetry and impedance spectroscopy to find an optimal ionomer composition in the catalyst layer.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.5
• /
• pp.1356-1364
• /
• 2014

A new conjugated copolymer, poly{4,8-bis(triisopropylsilylethynyl)benzo[1,2-b:4,5-b']dithiophene-alt-4,7- bis(5-thiophen-2-yl)-5,6-difluoro-2-(heptadecan-9-yl)-2H-benzo[d][1,2,3]triazole} (PTIPSBDT-DFDTBTz), is synthesized by Stille coupling polycondensation. The synthesized polymer has a band gap energy of 1.9 eV, and it absorbs light in the range 300-610 nm. The hole mobility of a solution-processed organic thin-film transistor fabricated using PTIPSBDT-DFDTBTz is $3.8{\times}10^{-3}cm^2V^{-1}s^{-1}$. Bulk heterojunction photovoltaic cells are fabricated, with a conventional device structure of ITO/PEDOT:PSS/polymer:$PC_{71}BM$/Ca/Al ($PC_{71}BM$ = [6,6]-phenyl-$C_{71}$-butyric acid methyl ester); the device shows a power conversion efficiency (PCE) of 2.86% with an open-circuit voltage ($V_{oc}$) of 0.85 V, a short-circuit current density ($J_{sc}$) of 7.60 mA $cm^{-2}$, and a fill factor (FF) of 0.44. Inverted photovoltaic cells with the structure ITO/ethoxylated polyethlyenimine/ polymer:$PC_{71}BM/MoO_3$/Ag are also fabricated; the device exhibits a maximum PCE of 2.92%, with a $V_{oc}$ of 0.89 V, a $J_{sc}$ of 6.81 mA $cm^{-2}$, and an FF of 0.48.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.2
• /
• pp.144-149
• /
• 2017

A proton-conducting bisphenylpropaned sulfonated fluorinated blockcopolymer (BPSFBC) was synthesized. Five kinds of polymer electrolyted composite membranes were preparated by incorporating silica ($SiO_2$) with various weight ratio. And their characteristics were investigated by FT-IR (fourier transform infrared), $^1H-NMR$ ($^1H$ nuclear magnetic resonance), TGA (thermogravimetric analysis), water uptake, FE-SEM (field emission scanning electron microscopes), and ion conductivity properties. The water uptake and ion conductivity were increased until 9 wt% $SiO_2$, and then decreased. The maximum proton conductivity equal to $52mScm^{-1}$ was measured for the BPSFBC/$SiO_2$-9 composite membrane at $90^{\circ}C$ and 100% relative humidity. From the measured results, it is distinct that the manufactured composite membrane BPSFBC/$SiO_2$-9 can be considered as a polymer membrane suitable for a fuel cell electrolyte.

• Polymer(Korea)
• /
• v.34 no.2
• /
• pp.97-103
• /
• 2010

PMMA was grafted on MWCNT surface in order to prepare conducting film composed of 6FDAbased polyimide/MWCNT. The electrical conductivity of 6FDA-based polyimide/PMMA-g-MWCNT was investigated as a function of PMMA-g-MWCNT content. Dispersion of MWCNT in 6FDA-based polyimide composite film was better than the pristine MWCNT due to the interaction force between PMMA and 6FDA-based polyimide. Electrical conductivity was interpreted by percolation threshold theory. As a result, 6FDA-6FpDA/PMMA-g-MWCNT which have high critical exponents and low critical concentration showed better dispersion than polyimide composite material that contains DABA(diamino benzoic acid).