• 조명전기설비학회논문지
• /
• 제17권6호
• /
• pp.1-6
• /
• 2003

본 연구에서는 광원의 색온도와 연색성의 차이에 의한 밝음의 느낌을 연구하기 위하여 이종 램프간, 또한 동종 램프 간의 비교 실험을 시각 대상물로 흑백 인쇄문자지와 색상지를 사용하여 수행하였다. 백열전구, 형광램프, 고압 나트륨램프, 메탈헬라이드램프, 무전극 방전램프를 대상으로 실험을 수행한 결과, 이종 광원의 경우 밝음의 느낌 비는 백열전구를 제외한 광원의 경우 대체적으로 평균연색계수에 비례하는 경향이 있으며, 모든 시험 대상 광원의 경우 색온도에 비례하는 것으로 나타났다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.149-151
• /
• 2008

This paper presents an architecture for driving multiple parallel cold cathode fluorescent lamps (CCFLs) for back lighting applications. The key to the architecture is a proposed capacitive coupling approach for lamp ignition. This system is consist of a flyback converter, a single inverter to drive multiple lamps and conductive floating reflector. The topology is capable of driving a number of parallel lamps with independent accurate lamp, current regulation and improving cost effectiveness with significant reduction in size and weight, compared to typical high frequency ac ballast. Experimental demonstration results for ten of parallel CCFLs with simultaneous ignition.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 1996년도 추계학술발표회논문집
• /
• pp.49-52
• /
• 1996

This paper reports the development of an electronic starter for fluorescent lamps, which is so smartly designed that can be used directly in existing installations. The key point of the design lies in the protection of lamp filaments by sufficient preheating and at the same time in the control of time constant for start-up circuit. The starter is consisted of three system parts: a rectifier pact, a switching part. and a gate control part. The characteristics of the developed electronic starter is compared with those of a conventional glow starter. As a result, blackening of lamps is almost reduced due to the stable and idealized start-up characteristics. And, furthermore, it is shown that its slaving time is shortened at about half the level of the conventional one and the starting power is also reduced.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.589-592
• /
• 2001

In this paper, Electronic ballast for multiple fluorescent lamps based on the use of ferrite beads are presented. The use of this system in place of the conventional electromagnetic ballast results in lower power consumption and reduced maintenance cost, because the electronic system has higher efficiency and longer lamp lifetime than the electromagnetic ballast. In comparison with the conventional electronic ballast. The proposed system presents a significant reduction of cost. This reduction becomes were meaningful with the growing of the lamp number. The description of the lighting system, We show that the proposed model can be applied to multiple lamps electronic ballast by simulation processes.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.589-592
• /
• 2001

In this paper, Electronic ballast for multiple fluorescent lamps based on the use of ferrite beads are presented. The use of this system in place of the conventional electromagnetic ballast results in lower power consumption and reduced maintenance cost, because the electronic system has higher efficiency and longer lamp lifetime than the electromagnetic ballast. In comparison with the conventional electronic ballast. The proposed system presents a significant reduction of cost. This reduction becomes were meaningful with the growing of the lamp number. The description of the lighting system, We show that the proposed model can be applied to multiple lamps electronic ballast by simulation processes.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 F
• /
• pp.2075-2077
• /
• 1997

An electronic starter using MOSFET is developed to take advantage of ideal preheating and starting features which can extend the lifetime of fluorescent lamps. The preheating curcuit of the developed electronic starter is consisted of three parts - a full wave rectifier curcuit, an FET switching curcuit, and a timer curcuit for the gate switching. The curcuit allows sufficient preheating current flow before the starting to protect lamp filaments, nevertheless it shortens the Preheating time and enables a single pulse ignition at the peak level of the line voltage. Experimental results show that fluorescent lamps of 20-40W range can be initiated within rather short time of $1{\sim}1.5sec$ with preheating current of 0.6A. The electronic starter withstands more than 70.000 cycles switchings without noticeable blackening due to anode spot. These features provide Proper evidences for the advantage of direct replacement with the new starter.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제54권12호
• /
• pp.601-608
• /
• 2005

This paper presents a novel single-stage high-power-factor electronic ballast for fluorescent lamps operating in critical conduction mode. The proposed topology is based on integration of boost converter as power factor corrector(PFC) and a half-bridge high frequency parallel resonant inverter into a single stage. The input stage of the boost converter is operating in critical conduction mode for positive and negative half cycle voltage respectively at line frequency(60Hz). So that a boost converter makes the line current follow naturally the sinusoidal line voltage waveform. The simulated and experimental results for 100W fluorescent lamps operating at 42kHz switching frequency and 220V line voltage have been obtained. This proposed inverter will be able to be practically used as a power supply in various fields as induction heating applications, fluorescent lamp and DC-DC converter etc.

• 조명전기설비학회논문지
• /
• 제13권1호
• /
• pp.9-14
• /
• 1999

삼파장 형광등의 제작에서 문제가 되는 것은 원하는 목표 색을 맞추기 위하여 혼합하는 세 가지 형광물질의 혼합비율이다. 한 형광체의 광 스펙트럼이 약간 변형되거나, 공정변수에 의하여 변경되거나, Ar과 Kr 같은 불활성가스의 스펙트럼이 혼재하거나 또는 재래 할로인산칼슘이 공존할 경우 원하는 정확한 색을 찾기가 매우 힘들어지게 된다. 이 연구에서는 원하는 목표 색을 빠르게 찾는 방법을 연구하였다. 세 개의 각각의 단일색의 형광등과 3색을 서로 다른 비율로 혼합한 형광등을 만들고 각각의 스펙트럼을 측정한 후 이로부터 알곤과 수은의 스펙트럼을 빼서 변형 색 좌표를 얻었다. 이 변형 색 좌표로부터 적생에 대한 청색과 녹색의 광속비를 그의 무게 비에 대하여 도시하여 무게 대 광속비의 관계를 구하였다. 이 관계식을 이용하여 생산라인에서 삼파장 형광체의 단일 도포 및 할로인산칼슘을 1차로 도포하는 2중 도포를 실시하여 목표색을 조합해본 결과 만족할만한 결과를 얻었다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.98-103
• /
• 2001

In case that electronic ballast employing a valley-fill passive power factor correction (PFC) circuit is used for feeding fluorescent lamps, a new method to reduce crest factor of the lamp current is studied in this paper. In order to reduce crest factor to lower value, a pulse frequency modulation technique based on the waveform of the dc-link voltage which is predetermined by the passive PFC circuit, is taken into the switching control action of the electronic ballast. An equation-based analysis between the crest factor of lamp current and the effect of varying the inverter switching frequency is comprehensively performed.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 1999년도 학술대회논문집-국제 전기방전 및 플라즈마 심포지엄 Proceedings of 1999 KIIEE Annual Conference-International Symposium of Electrical Discharge and Plasma
• /
• pp.228-233
• /
• 1999

In this paper we develop an electronic starter circuit that is suitable for Neon sign operation of switch-start fluorescent lamps. The developed starter enable single pulse ignition of fluorescent lamp at the peak point of preheating current, irrespective of the position of the Tum-On signal. This is possible due to the sequential operation of two transistors different in their operation characteristics and a diode operation characteristic. The switching endurance test using this starter has been carried for more than 3000 hours for a single switch-start on a severe blinking condition of preheating of 0.1s and of successive lighting interval of 0.1s.