• Journal of Ocean Engineering and Technology
• /
• v.32 no.6
• /
• pp.427-432
• /
• 2018

Tidal current power is one of the energy sources of the ocean. Electricity can be generated by converting the flow energy of the current into the rotational energy of a turbine. Unlike tidal barrage, tidal current power does not require dams, which have a severe environmental impact. A floating-type tidal current power device can reduce the expensive support and installation cost, which usually account for approximately 41% of the total cost. It can also be deployed in relatively deep water using tensioned wires. The dynamic behavior of a floater and turbine force are coupled because the thrust and moment of the turbine affect the floater excursion, and the motion of the floater can affect the incoming speed of the flow into the turbine. To maximize the power generation and stabilize the system, the coupled motion of the floater and turbine must be extensively analyzed. However, unlike pile-fixed devices, there have been few studies involving the motion analysis of a moored-type tidal current power device. In this study, the commercial program OrcaFlex 10.1a was used for a time domain motion analysis. In addition, in-house code was used for an iterative calculation to solve the coupled problems. As a result, it was found that the maximum mooring load of 200 kN and the floater excursion of 5.5 m were increased by the turbine effect. The load that occurred on the mooring system satisfied the safety factor of 1.67 suggested by API. The optimum mooring system for the floating tidal current power device was suggested to maximize the power generation and stability of the floater.

• Journal of Ocean Engineering and Technology
• /
• v.36 no.6
• /
• pp.390-402
• /
• 2022

Offshore wind energy has become a major energy source, and various studies are underway to increase the economic feasibility of floating offshore wind turbines (FOWT). In this study, the characteristics of wave-induced motion of a combined wind-wave energy platform were analyzed to reduce the variability of energy extraction. A user subroutine was developed, and numerical analysis was performed in connection with the ANSYS-AQWA hydrodynamic program in the time domain. A platform combining the TLP-type FOWT and the Wavestar-type wave energy converter (WEC) was proposed. Each motion response of the platform on the second-order wave load, the effect of WEC attachment and Power take-off (PTO) force were analyzed. The mooring line tension according to the installation location was also analyzed. The vertical motion of a single FOWT was increased approximately three times due to the second-order sum-frequency wave load. The PTO force of the WEC played as a vertical motion damper for the combined platform. The tension of the mooring lines in front of the incident wave direction was dominantly affected by the pitch of the platform, and the mooring lines located at the side of the platform were mainly affected by the heave of the platform.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2012.06a
• /
• pp.442-443
• /
• 2012

This study propose a sea water heat exchanger for floating architectures, which can be used as heat source or heat sink of heat pump. Based on CFD(Computational Fluid Dynamics), experimental mock-up system is made and tested. Some evaluation performances are shown on this paper.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.4 no.4
• /
• pp.25-35
• /
• 2001

This study aims to find out the growth characteristics of riparian plants on the artificial floating islands (AFI). Three types of experiments were performed. The vegetation growth were compared by the plant-supporting materials; natural cotton mat, coir mat on the AFI or in the water, and natural soil at the waterfront. Major findings are; 1. The survival rate of riparian plants was 100% on both coir-mat and cotton-matislands, which implies that we may substitute cheaper cotton for expensive coir-mat. 2. Both natural cotton mat and coir mat were good for the growth of plants. Especially, the natural cotton mat was good for Sparganium stoloniferum and Miscanthus sacchariflorus, and the coir mat was good for Typha latifolia. 3. The growth rate of stem and root showed difference between the stem-removed plants and stem-remaining plants. As a whole, the growth rate of stem-removed plants was bigger than the one of stem-remaining plants. 4. The growth rate of plants showed difference between those grown on the AFI and those grown in the water. The growth rate of plant on the AFI was bigger than the one in the water. 5. The growth rate of plants on the AFI was bigger than the one on the natural soil at the waterfront.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2013.10a
• /
• pp.287-288
• /
• 2013

Concerns on the floating architecture development has been increased on the viewpoint of ocean space due to the increases of GDP and environmental issues such as sea level rise. However, basic research on the water heat exchanger for utilizing seawater thermal energy is insufficient. So, The purpose of this research is to develop a sea water heat exchanger model and to evaluate the performance throughout the experiment for seawater heat utilization.

• International Journal of Ocean System Engineering
• /
• v.1 no.4
• /
• pp.198-204
• /
• 2011

Recently, several problems have occurred in the space, infra-structure, and facility of the contiguity of existing harbors due to the trend of enlarged container vessels. In this regard, the Mobile Harbor has been proposed conceptually in this study as an effective solution for these problems. The concept is that of a transfer loader that transfers containers from a large container ship to the harbor on land, and is a catamaran type floating barge. The catamaran-type vessel is well known for its advantage in maneuverability, resistance, and effectiveness for working on board. For the safe and effective operation of the two floating bodies (a container ship and the mobile harbor in the near sea detached from the quay), robot arms, novel crane systems, and pneumatic fenders are specially devised with an additional mooring facility or DP (dynamic positioning) system. In this study, this concept is to be verified through comparison and simulation studies under various environmental conditions. It is shown that the proposed concept is in general feasible but there are several areas for further investigation and improvement.

• Journal of Navigation and Port Research
• /
• v.36 no.7
• /
• pp.545-552
• /
• 2012

Domestic marina facilities today consist mostly of composite-type marinas with particular spatial composition characteristics, due to the regulatory restrictions that keep their development in the public sector and the tepid growth of marine leisure-sports. To develop a marina club design appropriate for domestic conditions, this study establishes space program standards for designing Korean marinas based on a case analysis of existing marina clubs and a survey of floating marina clubs. It is possible for a current composite-type Korean marina club to have a spatial composition of 16~18% for marina-exclusive facility (mFA), 47~49% for commercial facility (cFA), 27~30% for public space (pFA) and 5~8% for management space (emFA). With this composition as a basis, space program estimation of a Korean marina club can be done through the process of estimating in order the marina-exclusive facility area, the floor area by each space and the total floor area, the first floor area, the deck area and the pontoon area. Since the space program established in this study can be utilized as a tool for designing a Korean marina club, it is expected to be helpful in designing marina clubs in the future.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.320-323
• /
• 2010

This paper proposes efficient log and exponent calculation methods using a dual phase instruction set without additional ALU unit for a mobile enviroment. Using the Dual Phase Instruction set, it extracts exponent and mantissa from expression of floating point and calculates 24bit single precision floating point of log approximation using the Taylor series expansion algorithm. And with dual phase instruction set, it reduces instruction excution cycles. The proposed Dual Phase architecture reduces the performance degradation and maintain smaller size.

• Journal of Ocean Engineering and Technology
• /
• v.22 no.2
• /
• pp.20-27
• /
• 2008

A moon-pool is a vertical well in a floating barge, drilling ship, or offshore support vessel. In this study, numerical simulation of two-dimensional moon-pool flaw coupled with a ship's motion in waves is carried out using a particle method, the so-called MPS method. The particle method, which is recognized as one of the gridless methods, was developed to investigate nonlinear free-surface motions interacting with structures. The method is more feasible and effective than convectional grid methods in order to solve a flaw field with complicated boundary shapes.

• Journal of Navigation and Port Research
• /
• v.43 no.5
• /
• pp.328-334
• /
• 2019

Underwater architecture in providing a comfortable living space underwater is mandated to survive prevailing environmental loads, especially hydrostatic ambient water pressure exerted on the structure of individual habitat hulls at depth and hydrodynamic fluctuation of external forces that perturb the postural equilibrium and mooring stability of the underwater housing system, for which the design including the hull shape and mooring system constraint the responses. In this study, the postural stability of a proposed underwater floating housing system with three vertically connected ellipsoidal-shape habitat hulls of different sizes are theorized and calculated for hydrostatic stability, using MATLAB in the volumetric integration of a hull and the weight of operational loads under assumed scenarios. The assumptions made in the numerical method to estimate the stability of the habitat system include the fixed weight of the hulls, and their adjustable loads within operational limits for the set meteorological oceanic conditions. The purpose of this study was to numerically manipulate a) The buoyancy and b) The adjusted center of mass of the system within the range of designed external and internal load changes, by which the effective mooring system capability and postural equilibrium requirements were argued with the quantitative analysis.