• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.3
• /
• pp.268-276
• /
• 2013

The objective of this paper is to give a general understanding for the development flight test of Korean Utility Helicopter(KUH). This paper contains the contents of detailed flight test plan, the type of flight test, an introduction to main flight test area, and the overview of flight test results. At the beginning, more than 8,500 test points were identified for airworthiness certification to show the compliance for the KUH development requirements. However, the number of flight test points were optimized to 7,800 at the end. To accomplish the test objectives, about 860 flight test sorties had been performed, and more than 1,000 test sorties were consumed for trouble shooting. This paper also describes some major issues faced during development flight test phase.

• Journal of Aerospace System Engineering
• /
• v.5 no.1
• /
• pp.36-40
• /
• 2011

In this report US and Korea civil and military simulator certification system is researched, and a plan for improvement is proposed. Korean simulator certification system should adopt FAA's system and improve upon it. Certification criteria should have a basis on FAA certification criteria and add military operation characteristics selectively. Flight test data, used as comparison criteria in certification, should be acquired in package during aircraft development or overseas acquisition. The establishment of certification system is expected to improve external credibility and improve competitiveness in overseas market.

• Aerospace Engineering and Technology
• /
• v.7 no.1
• /
• pp.142-150
• /
• 2008

In order to ensure the individual and mutual performances among the telemetry system, tracking system, flight termination system, GPS, and inertial navigation & guidance system which are installed in the KSLV-I 2nd stage and ground equipment of the Naro space center, flight test using a light airplane is required. Since the high degree of test efficiency is fulfilled through the minute plan and analysis about selection of the equipment which are applicable to the test, harness, operation strategy, and antenna installation. KSLV-I communication environment and flight profile should be precisely taken into account during the flight test. In this document, overall aspect of the KSLV-I 2nd stage equipment specification, a rack for the installation, harness, the airplane specification, and flight route which are required for the effective flight test are presented.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1054-1056
• /
• 2017

The Preparation for a flight test of the launch vehicle to verify the performance of the liquid rocket engine(LRE) is proceeding. Flight test of liquid rocket engine costs an enormous amount of money, has a restriction on measurement channels, so it requires the optimal measurement plan to check the prelaunch operation and determine the cause of abnormal situation. This paper surveys the foreign sources for LRE flight test. In recent years, as the tendency to eliminate all faults of LRE at the ground test the number of flight test is decreasing and in contrast, the number of measurements and measurement accuracy is increasing. This paper may be used as a reference for the preparation of an LRE flight test.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.3
• /
• pp.405-413
• /
• 2011

Defense Systems Test Center in ADD supports increasingly various missile test requirements such as higher altitude event, multi target operation and low-altitude, high velocity target tracking. In this paper, we have proposed the development of instrumentation radar tracking status simulator based on virtual reality. This simulator can predict the tracking status and risk of failure using several modeling algorithms. It consists of target model, radar model, environment model and several algorithms includes the multipath interference effects. Simulation results show that the predict tracking status and signal are similar to the test results of the live flight test. This simulator predicts and analyze all of the status and critical parameters such as the optimal site location, servo response, optimal flight trajectory, LOS(Line of Sight). This simulator provides the mission plan with a powerful M&S tool to rehearse and analyze instrumentation tracking radar measurement plan for live flight test at DSTC(Defense Systems Test Center).

• Aerospace Engineering and Technology
• /
• v.8 no.1
• /
• pp.1-9
• /
• 2009

The ground integration test of Smart UAV has been performed according to the flight test plan. The flight test of full scaled model will be performed followed by 4 DOF ground rig test and a tethered hover test. Smart UAV is the first indigenous tiltrotor aircraft which can fly with fast cruise speed and take off or land vertically. In order to prove the flight control law of Smart UAV, the 40% scaled airplane was developed and have been tested. During flight test of small scaled model, many unique and unexpected problems occurred. After clearing these problems, fully automatic flight test was performed successfully. The experiences about many trouble shooting and resolving the problems would be basic material to avoid the unexpected but similar flight test problems hidden behind of the full scaled Smart UAV. This paper presents the detailed procedures of trouble shootings to solve the unique problems which occurred during the flight test of small scaled tiltrotor UAV.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.4
• /
• pp.541-550
• /
• 2018

The works of preparing for missile flight test are becoming more complicated. To reduce the amount of waste time along with the complexity of the task, systematic analysis of waste factors should be performed before performing process improvement. The waste factors for missile flight test are first defined using lean-based waste factors. The improvement priorities for the defined waste factors are surveyed. For reliable analysis, AHP is used in questionnaire analysis instead of the existing method with large error. Then weighting and priority for waste factors for level 1 and Level 2 are suggested. Through AHP, we could derive reliable improvement priorities for waste factors. It is analyzed that the biggest cause of waste factors is waiting time and identified as the first item to be considered when establishing improvement plan. In addition, suggestions for improvement measures of waste factors are presented through brainstorming method. Reliable results will be an important factor in process redesign for missile flight test works.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.465-467
• /
• 2012

A layout plan of a pressure-fed test facility to carry out hot-firing test of liquid rocket engine combustion chamber and purpose of rooms located in the test building were proposed. The layout plan of suggested infrastructure in this paper was determined depending on the design of a vertical test facility to use the natural lay of the land and simulate the initial position of flight model.

• Proceedings of the KSRS Conference
• /
• 2008.10a
• /
• pp.84-87
• /
• 2008

ATTOL is a software unit testing tool produced by the ATTOL Testware SA in France. It automates the entire software unit testing process: test plan template and test program generation, test program execution, test result analysis and test report generation. ATTOL is suited for the development of embedded software as it allows programmers to operate in native and cross development environments. Particularly, it is used for the development of the flight software which is embedded in the Communication Ocean Meteorological Satellite (COMS). As the flight software is mission-critical, it requires the strict software quality and high testing constraints. The flight software of COMS is verified by ATTOL in native and cross platforms. In 2002, ATTOL was taken over by the IDM Rational Software and has been supplied with the name of Test RealTime (TestRT). The test process of TestRT becomes different from that of ATTOL as TestRT provides the new functionalities that were absent from ATTOL. TestRT provides the new features in the test script language, as well. In this paper, we compare the test process of ATTOL to TestRT With an example of COMS and explain what has been changed in the test script language.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.1-1
• /
• 2005

Japan Aerospace Exploration Agency(JAXA) has been conducting research and development of the Scramjet engines and their derivative combined cycle engines as hypersonic propulsion system for space access. Its history will be introduced first, and its recent advances, focusing on the engine performance progress, will follow. Finally, future plans for a flight test of scramjet and ground test of combined cycle engine will be introduced. Two types of test facilities for testing those hypersonic engines. namely, the 'Ramjet Engine Test Facility (RJTF)' and the 'High Enthalpy Shock Tunnel (HIEST)' were designed and fabricated during 1988 through 1996. These facilities can test engines under simulated flight Mach numbers up to 8 for the former, whereas beyond 8 for the latter, respectively. Several types of hydrogen-fueled scramjet engines have been designed, fabricated and tested under flight conditions of Mach 4, 6 and 8 in the RJTF since 1996. Initial test results showed that the thrust was insufficient because of occurrence of flow separation caused by combustion in the engines. These difficulty was later eliminated by boundary-layer bleeding and staged fuel injection. Their results were compared with theory to quantify achieved engine performances. The performances with regards to combustion, net thrust are discussed. We have reached the stage where positive net thrust can be attained for all the test coditions. Results of these engine tests will be discussed. We are also intensively attempting the improvement of thrust performance at high speed condition of Mach 8 to 15 in High Enthalpy Shock Tunnel (HIEST). Critical issues for this purposemay be air/fuel mixing enhancement, and temperature control of combustion gas to avoid thermal dissociation. To overcome these issues we developed the Hypermixier engine which applies stream-wise vortices for mixing enhancement, and the M12-engines which optimizes combustor entrance temperature. Moreover, we are going to conduct the flight experiment of the Hypermixer engine by utilizing flight test infrastructure (HyShot) provided by the University of Queensland in fall of 2005 for comparison with the HIEST result. The plan of the flight experiment is also presented.