• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.436-437
• /
• 2008

Flexible CIGS thin film solar cell was fabricated using STS430 plate as a flexible substrate in this work. A diffusion barrier layer of $SiO_2$ thin film was deposited on STS430 substrate by PECVD followed by deposition of double layered Mo back contact. After depositing CIGS absorber layer by co-evaporation, CdS buffer layer by chemical bath deposition, ZnO window layer by RF sputtering and Al electrode by thermal evaporation, the solar cell fabrication processes were completed and its performance was evaluated. Corresponding solar cell showed an conversion efficiency of 8.35 % with $V_{OC}$ of 0.52 V, $J_{SC}$ of 26.06 mA/$cm^2$ and FF of 0.61.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.3
• /
• pp.163-168
• /
• 2020

We studied the change of photovoltaic properties of a flexible CuIn_xGa(_1-x)Se₂ (CIGS) solar cell fabricated on polyimide by mechanical bending with curvature radii of 75 mm (75R) and 20 mm (20R). The flexible CIGS cells were flattened on a PET film, then placed and forced against the surface of a curved block fabricated with pre-designed curvatures. Both up (compressive) and down (tensile) bending were applied to a specimen of CIGS on PET with curvatures of 75R and 20R for 10,000 times and 2,000 times, respectively. From J-V measurements, we found that the conversion efficiency (Eff.) was reduced by 3% and 4% for up-and down-bending, respectively, at curvature 75R; it was greatly reduced by 15% for curvature 20R in the up-bending. However, the open circuit voltage (V_oc) and short-circuit current density (J_sc) seemed to change little, within 3%, for the applied mechanical stresses. The degradation in Eff. resulted from the deterioration of the series (R_s) and shunt (R_sh) resistances of the solar cell.

• Journal of Applied Reliability
• /
• v.16 no.1
• /
• pp.41-47
• /
• 2016

Purpose: The purpose of this study was to evaluate electrical and structural degradation of flexible CIGS sollar cell exposed to high temperature and humid atmosphere. Method: Accelerated degradation was performed for various time under $85^{\circ}C/85%RH$ and then electrical and structural properties were analyzed by 4-point probe method, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). Results: Sheet resistance of the top ITO layer increased with exposure time to the high temperature and humid atmosphere. Blunting of the protrusion morphology of ITO layer was observed for the degraded specimen, while no phase change was detected by XRD. Oxygen was detected at the edge area after 300 hours of exposure. Conclusion: Increase in electrical resistance of the degraded CIGS solar cell under high temperature and humid environment was attribute to the oxygen or water absorption.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.153-155
• /
• 2009

In this study, we fabricated the $Cu(In,Ga)Se_2$ (CIGS) thin-film solar cells by using a polyimide substrate. The CIGS thin-film was deposited on Mo coated polyimide substrate by a 3-stage co-evaporation technique. Because the polyimide shows thermal transformation at about $400^{\circ}C$, the substrate temperature of co-evaporation process was set to below $400^{\circ}C$. Corresponding solar cell showed a conversion efficiency of 7.08 % with $V_{OC}$ of 0.58 V, $J_{SC}$ of 24.99 $mA/cm^2$ and FF of 0.49.

• Journal of Surface Science and Engineering
• /
• v.48 no.1
• /
• pp.23-26
• /
• 2015

What causes the transformation of a solar cell is the behavior difference of thermal expansion occurred between the substrate and the layer of semiconductor used in the solar cell. Therefore, the substrate has to possess a behavior of thermal expansion that is similar with that of semiconductor layer. This study employed electroforming to manufacture Fe-Ni alloy materials of different compositions. To verify the result from a finite element analysis, a two-dimensional Mo substrate was calculated and its verification experiment was conducted. The absolute values from the finite element analysis of Mo/substrate structure and its verification experiment showed a difference. However, the size of residual stress of individual substrate compositions had a similar tendency. Two-dimensional CIGS/Mo/$SiO_2$/substrate was modeled. Looking into the residual stress of CIGS layer occurred while the temperature declined from $550^{\circ}C$ to room temperature, the smallest residual stress was found with the use of Fe-52 wt%Ni substrate material.

• Journal of Surface Science and Engineering
• /
• v.46 no.2
• /
• pp.61-67
• /
• 2013

Thin film solar cells have attracted much attention due to their high cell efficiency, comparatively low process cost, and applicability to flexible substrates. In particular, CIGS solar cells have been widely studied and produced because they demonstrated the highest cell efficiency. However, the deposition process of CIGS films generally includes the selenization process conducted at elevated temperature using toxic $H_2Se$ gas. To avoid this selenization process, CIGS thin films were, in this study, deposited by RF sputtering using single composite CIGS target. In addition, the effects of sputtering bias voltage and heat treatment on the microstructural and morphological changes in deposited CIGS films were investigated and discussed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.58.1-58.1
• /
• 2011

CIS(CuInSe2)계 화합물 태양전지는 높은 광흡수계수와 열적 안정성으로 고효율 태양전지 제조가 가능하여 태양전지용 광흡수층으로 매우 이상적이다. 미국 NREL에서는 이러한 CIGS 태양전지를 Co-evaporation 방법으로 제조 20%이상의 에너지 변환 효율을 달성하였다고 보고하였다. CIGS 태양전지의 경우 기존의 유리 기판 대신 유연한 철강 기판을 사용해 태양 전지를 flexible하게 제조 할 수 있다는 장점이 있다. 이러한 flexible 태양전지의 경우 기존의 rigid 태양전지의 적용분야 뿐만 아니라 BIPV, 선박, 장난감, 군용, 자동차등 더욱 더 많은 분야에 활용이 가능하다. 본 연구에서는 기존의 rigid한 기판인 soda lime glass와 flexible 기판인 stainless steel 기판으로 소자를 제조하여 효율을 비교 분석 및 stainless steel 기판의 표면 처리 방법에 따라서 표면 조도의 특성을 분석하여 stainless steel 기판별 효율 특성도 비교 분석 하였다. 후면전극으로는 약 $1{\mu}m$의 Mo를 DC Sputtering 방법을 이용하여 증착하였고, CIGS 광흡수층은 약 $2.5{\mu}m$의 두께로 미국의 NREL과 같은 3 stage 방식을 이용하여 광흡수층을 Co-Evaporation 방법으로 제조하였고, 버퍼층인CdS는 약 50nm의 두께로 CBD 방법으로 제조 하였으며, 창층인 ZnO는 약 500nm 두께로 RF Sputtering 방법으로 제조 하였고, 마지막으로 약 $1{\mu}m$ 두께의 Al 전면전극은 Thermal Evaporation 방법으로 제조 하였다. 소자의 물리적, 전기적 특성을 분석하기위해 FE-SEM, AFM, Solar Cell Simulator 분석을 실시하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.600-613
• /
• 2018

The purpose of this research was to introduce a network analysis method for analyzing the recent trend of the flexible solar cell using a scholarly database. Based on the five years from 2013 to 2017, we used centrality analysis of research papers via measurement of degree centrality, closeness centrality, and betweenness centrality. The results of network analysis show that cell has a centrality value above 0.8, which means that cell is connected with 80% of the total keywords, so it is recognized as the center of flexible solar cell research. The analysis results also indicate that perovskite and copper indium gallium diselenide (CuInGaSe2, or CIGS) are the center of the subgroup for cell. We recognize that the result refers to recent new technology called the CIGS/perovskite tandem solar cell. We hope that the network analysis method will be the appropriate and precise tool for technology and research planning via elaboration and optimization.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.61.1-61.1
• /
• 2010

$CuIn_{1-x}-GaxSe_2$ based materials with direct bandgap and high absorption coefficient are promising materials for high efficiency hetero-junction solar cells. CIGS champion cell efficiency(19.9%, AM1.5G) is very close to polycrystalline silicon(20.3%, AM1.5G). A reduction in the price of CIGS module is required for competing with well matured silicon technology. Price reduction can be achieved by decreasing the manufacturing cost and by increasing module efficiency. Manufacturing cost is mostly dominated by capital cost. Device properties of CIGS are strongly dependent on doping, defect chemistry and structure which in turn are dependent on growth conditions. The complex chemistry of CIGS is not fully understood to optimize and scale processes. Control of the absorber grain size, structural quality, texture, composition profile in the growth direction is important to achieving reliable device performance. In the present work, CIS nanoparticles were prepared by a simple wet chemical synthesis method and their structural and optical properties were investigated. XRD patterns of as-grown nanopowders indicate CIS(Cubic), $CuSe_2$(orthorhombic) and excess selenium. Further, as-grown and annealed nanopowders were characterized by HRTEM and ICP-OES. Grain growth of the nanopowders was followed as a function of temperature using HT-XRD with overpressure of selenium. It was found that significant grain growth occurred between $300-400^{\circ}C$ accompanied by formation of ${\beta}-Cu_{2-x}Se$ at high temperature($500^{\circ}C$) consistent with Cu-Se phase diagram. The result suggests that grain growth follows VLS mechanism which would be very useful for low temperature, high quality and economic processing of CIGS based solar cells.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.116.2-116.2
• /
• 2011

연성 CIGS 태양전지를 제작하기 위해서는 휘어지는 연성 기판재의 적용이 반드시 필요하다. 상용되는 연성 기판재로는 플라스틱, 폴리이미드, 금속재가 있다. 그러나 플라스틱과 폴리이미드는 고효율의 CIGS 흡수층을 제조하기 위한 $500{\sim}600^{\circ}C$의 공정에 접합하지 못하다. 금속 기판재의 경우는 몰리브데늄, 알루미늄, 티타늄, 크롬강, 스테인레스강, 합금재 등이 있다. 이러한 금속 기판재 중에서 Fe-Ni 합금재는 Ni 함량의 변화에 따라 기계적, 자기적, 열팽창 특성이 다르게 나타나는 것으로 알려져 있다. 선행 연구에서 CIGS 태양전지의 기판재로 열팽창 계수가 박막층과 유사한 SUS400번 계열과 Fe-52Ni이 적합하다는 것을 확인 하였다. 따라서 본 연구에서는 유한요소해석(Finite element analysis) 프로그램인 Algor를 이용하여 CIGS solar cell을 설계하고 Fe-52Ni 기판재와 절연층인 SiO2, 흡수층인 CIGS의 두께에 따른 Cell의 잔류응력을 해석하였다.