• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.23-26
• /
• 1997

This work presents the TMAH/IPA anisotropic etching characteristics with addition of Pyrazine. (100) Si etching rate of 0.747 ${\mu}{\textrm}{m}$/min at 8$0^{\circ}C$ was obtained using TMAH 25 wt.% / IPA 17 vol.% / pyrazine 0.1 g. The etching rate of (100) Si is increased about 52% compare to pure TMAH 25 wt.%. But etching rate of (100) Si is decreased with increasing Pyrazine additive. Activation energy of TMAH/IPA/pyrazine is much lower than TMAH and TMAH/IPA solutions. Addition of Pyrazine does not effect on surface flatness and decreases undercutting ratio about 20 %. Therefore, TMAH/IPA/pyrazine is an attractive anisotropic etchant because of alkaline-ion free.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.7
• /
• pp.819-825
• /
• 1988

An 1-bit DPCM image coding method is presented. Our method is specially designed to reduce the slope overload which seems to be the major performance degradation factor in 1-bit DPCM. In the present algorithm, based on the classification of neighborhoods by its flatness, slope strength and direction, predictor and quantizer operate adaptively through switching action. Compared with some other methods by computer simulation, proposed method shows improved performance in image quality as well as in signal to noise ratio. This gain mainly comes from the reduced slope overload and seems large to compensate the increased complexity in prediction. As a post processing, Lee filter is used to reduce the granular noise subjectively annoying in flat region.

• Radiation Oncology Journal
• /
• v.6 no.1
• /
• pp.101-108
• /
• 1988

The beam characteristics and dosimetric measurements of the 10MV X-ray beam from a Mevatron KD linear accelerator are examined. The Percent Depth Dose (POD) table and the Tissue Maximum Ratio (TMR) table are taken from measurement as a function of the field size and the depth. The calculated TMR table from PDD table is compared with those from measurement. Other beam characteristics such as output factor, beam profile (including flatness, symmetry and penumbra), wedge, and the variation of Dmax are presented.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.05a
• /
• pp.151-152
• /
• 2016

In this study, the shrinkage properties of concrete with the high-performance shrinkage admixture and the crack reinforcing materials applied to the high-flatness flooring of hypermarkets, outlets and warehouses was evaluated. The concrete with the popular shrinkage admixture is significantly reduced compared to the plain concrete without shrinkage admixture for the dry shrinkage deformation, and the difference of shrinkage ratio between the concretes has been shown to increase with increasing age.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.2
• /
• pp.153-161
• /
• 2002

Stable polyaniline-dodecylbenzenesulfonic acid(PANI-DBSA) fully dissolved in toluene was obtained by a direct one-step emulsion polymerization technique. By using the proper molar ratio of APS/aniline monomer and DBSA/aniline monomer, the highest conductivity(7 S/cm) of PANI was obtained. The UV-Vis absorption spectrum of PANI confirmed PANI is emeraldine salt form. PANI/styrene polymers (polystyrene and styrene-butadiene copolymer) blends were prepared by mixing PANI solution with polymers in toluene. These blends exhibited the conductivity of 10$\^$-4/-10$\^$-3/ S/cm at 1 wt. % of PANI content. The mechanical property of conducting blend was decreased and TGA thermograms of conducting blends were similar to that of PANI. It had been checked that the flatness of coating layers of conducting blends decreased with increasing conducting components. It was also found that the morphology of blends was setting closer to that of PANI at higher conducting component contents.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.6
• /
• pp.2160-2170
• /
• 1991

Three-dimensional turbulent structures in the near field of elliptic jet were experimentally investigated by using a three-color, three-component Laser Doppler Velocimeter. The Reynolds number based on the nozzle exit velocity and nozzle equivalent diameter(De) was about 4*10$^{4}$. The turbulent characteristics of a sharp-edged elliptic nozzle with aspect ratio of 2 were analyzed along major and minor axis at X/De=2,3,5,7 and along the centerline up to X/De=14. Quantities measured at each point with the 3-D LDV system were three orthogonal velocity components, turbulent intensity, skewness, flatness, and Reynolds shear stress. The nondimensional mean velocities coincided well with the Schlichting's empirical curve with going downstream. Elliptic jet of AR=2 had two switching points at about X/De=2 and 16. The turbulent intensity along the minor axis was distributed widely than that along the major axis. In the near field, X/De<5, the Reynolds shear stresses of the inner part of the elliptic jet had negative value, which indicated the enhancement of entrainment toward the inner part.

• Transactions of Materials Processing
• /
• v.25 no.4
• /
• pp.235-241
• /
• 2016

Dimensional accuracy of hot coil is improved by precise control of thickness profiles, flatness, width and winding profile. Especially, precise width control is important because yield could be increased significantly. Precise width control can be improved by predicting the amount of width spread. The purpose of this study is to develop the advanced prediction model for width spread in hot finish rolling for controlling width precisely. FE-simulations were performed to investigate the effect of process variables on width spread such as reduction ratio, forward and backward tension and initial width at each stand. From the statistical analysis of simulated data, advanced model was developed based on the existing models for strip width spread. The experimental hot rolling trials showed that newly developed model provided fairly accurate predictions on the strip width spread during the whole hot finishing rolling process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.7
• /
• pp.724-728
• /
• 2004

This paper describes on RIE(Reactive Ion Etching) characteristics of 3C-SiC(Silicon Carbide) grown on Si(100) wafers. In this work, CHF$_3$ gas was used to form the polymer as a function of a side-wall for excellent anisotropy etching during the RIE process. The ranges of the etch rate were obtained from 60 $\AA$/min to 980 $\AA$/min according to the conditions such as working gas pressure, RF power, distance between electrodes and the $O_2$ addition ratio in working gas pressure. Under the condition such as 100 mTorr of working gas pressure, 200 W of RF power and 30 mm of the distance between electrodes, mesa structures with about 40 of the etch angle were formed, and the vertical structures could be improved with 50 % of $O_2$ addition ratio in reactive gas during the RIE process. As a result of the investigation, we know that it is possible to apply the RIE process of 3C-SiC using CHF$_3$ for the development of electronic parts and MEMS applications in harsh environments.

• Current Optics and Photonics
• /
• v.5 no.5
• /
• pp.576-582
• /
• 2021

Dichroic beam-splitter (DBS) with polarization-maintaining took an important role in the free space quantum telecommunication tests on the Micius satellite of China. In this presentation, we designed and prepared a 50 layer polarization-maintaining DBS coating by a dual ion beam sputtering deposition (Dual-IBS) method. In order to solve a stress problem, an 18 layer special anti-reflection (AR) coating with similar physical thickness ratio was deposited on the backside. By stress compensation, the surface flatness RMS value of the DBS sample decreased from 0.341 λ (@632.8 nm) to 0.103 λ while beam splitting and polarization maintaining properties were almost kept unchanged. Further, we discussed the mechanism of film stress and stress compensation by equation deduction and found that total stress had a strong relationship with the total physical thickness and the ratio of layer materials.

• Journal of Conservation Science
• /
• v.35 no.4
• /
• pp.269-277
• /
• 2019

Seaweed extracts, namely carrageenan obtained from Grateloupia elliptica and algin obtained from Laminaria, were employed as adhesive agents to synthesize solid adhesives for paper. Carrageenan from Grateloupia elliptica with the highest adhesive strength and lgin from Laminaria with the highest compressive strength was selected. The selected carrageenan and algin were mixed in a ratio of 7:3, and the mixture was employed as an adhesive agent. At a high temperature, sodium stearate(used as a solidifying material) oxidized the seaweed extracts. Consequently, carrageenan and algin were added to the final manufacturing process. The adhesive strength of the final synthesized solid adhesive is found to be 3.02 MPa and the compressive strength is found to be 30.5 N. Compared to the adhesive strength (2.95 MPa) and compressive strength (30.11 N) of commercial solid adhesives, the obtained results indicate superior adhesion characteristics. Furthermore, the proposed adhesive is environment-friendly because the presence of volatile organic compounds, formaldehyde, and heavy metals(such as chromium, lead, and cadmium) were not detected. Moreover, when used, the flatness of paper was twice that of commercial solid paper adhesives. Hence, the proposed adhesive can provide excellent adhesion, stability, and usability.