• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.414-417
• /
• 2001

Recently, developments of device using characteristics of ceramics as a new technical material is in progress. While doing so, Ultrasonic motor which is a part of research & flat-type $L_1-B_8$ mode Ultrasonic motor and measured the operation characteristics of its. The size of USM is 80*20*1.5[$mm{^1}$](length*width*thickness) and is constructed with stator by piezo-ceramics and stainless elastic body and rotator by bearings. As results of experiments, the fastest speed of revolution($\upsilon$), the maximum torque(T) and the efficiency($\eta$) were 37.5[cm/sec], 5.0[mN$\cdot$M] and 1.17[%] respectively when 27.9[kHz], 150[gf], 50[V] were applied. SO, we think this flat-type $L{_1}-B{_8}$ mode Ultrasonic motor is able to be used for applications in forwarding device of a paper or electric card so on. Key Words: Flat=type $L{_1}-B{_8}$ mode Ultrasonic Motors, Piezoelectric ceramics, forwarding device.

• Proceedings of the KIEE Conference
• /
• 2004.10a
• /
• pp.31-33
• /
• 2004

In order to simulate the dynamic characteristics, we have developed a new method of calculating the torque of the flat-type vibration motor which is using 2D finite element model. We have measured the load torque of the vibration motor which is used for the dynamic characteristics analysis. The simulated vibration characteristic is compared with experimental value.

• Journal of IKEEE
• /
• v.2 no.1 s.2
• /
• pp.160-165
• /
• 1998

This paper describes a method for field analysis inside the flat-type brushless DC motor using 2-D field simulator. Rigorous field analysis entail 3-D analysis. However, this analysis is not often appropriate for system designs because of the time and cost involved. For field analysis in this study, the 3-D problem is reduced to a 2-D boundary value problem by introducing a cylindrical cutting plane at the mean radius of the magnets. Independent of sizes and shapes of systems, the exact 2-D field results can be obtained with reasonable predictability.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.414-417
• /
• 2001

Recently, developments of device using characteristics of ceramics as a new technical material is in progress. While doing so, Ultrasonic motor which is a part of research & development of piezo-actuator by piezo-effects is being used in the various applications. So, we fabricated a flat-type $L_{1}-B_{8}$ mode Ultrasonic motor and measured the operation characteristics of its. The size of USM is 80*20*1.5[$mm^{3}$](length*width*thickness) and is constructed with stator by piezo-ceramics and stainless elastic body and rotator by bearings. As results of experiments, the fastest speed of revolution(v), the maximum torque(T) and the efficiency( $\eta$ ) were 37.5[cm/sec], 5.0[ $mN{\cdot}m$ ] and 1.17[%] respectively when 27.9[kHz], 150[gf], 50[V] were applied. So, we think this $flat-type_{1}-B_{8}$ mode Ultrasonic motor is able to be used for applications in forwarding device of a paper or electric card and so on.

• Journal of Advanced Information Technology and Convergence
• /
• v.9 no.2
• /
• pp.107-113
• /
• 2019

In this study, we examined the feasibility of considering the transverse edge effect of flat type linear induction motor as 2D finite element analysis (FEA) by changing the resistivity of secondary conductor. For this purpose, the 3D FEA analysis results were compared with the 2D FEA analysis results with the change of the resistivity of the secondary conductors. As a result, simply changing the resistivity could not accurately account for the transverse edge effect of LIM because of leakage components that could not be considered by 2D FEA.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.7
• /
• pp.292-297
• /
• 2002

In this paper, a flat-type $L_{-}$-$B_{8}$ mode Ultrasonic Motor[USM] having the size of 80 x 20 x ${1.5}mm^3$($l{\times}\omega{\times}t$) was designed and fabricated to examine the characteristics of an ultrasonic vibration. We used ANSYS simulation program based on FEM to get the optimum design of this USM. As results of experiment, the fastest speed of revolution(v), the maximum torque(T) and the efficiency(n) were 37.5cm/s, 5.0 mN.m and 1.17% when 27.9KHz, 150N, 50V were applied respectively. And this flat-type $L_{-}$-$B_{8}$ mode USM could be controlled the speed of rotor revolution by applied voltage, frequency and pre-load of rotor as well as showed the characteristics of typical drooping torque-speed, large torque and high speed. So, we think that this flat-type $L_{-}$-$B_{8}$ mode USM has characteristics of enough torque and velocity to be usable for applications in forwarding device of an electric card or a paper, etc.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.11
• /
• pp.1153-1162
• /
• 1990

The torque ripple reduction method is studied to improve the speed fluctuation of permanent magnet flat type brushless DC motors. To reduce the torque ripple, this study developed the compensation method of the 5'th harmonics component of air gap flux waveform which pass through the driving coils. 1/2 inch VTR was considered. As the result of this study, we can reduce the torque ripple and the speed fluctuation of the capstan motor about 20% then before and we can obtain not only better characteristics of wow/flutter but more useful capstan motors which can be applied in the multi-function VTRs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.664-667
• /
• 2001

A flat-type L$_1$-B$_{8}$ Mode Ultrasonic motor(USM) uses longitudinal-bending multi-mode vibrator which is constructed with the metal-piezoceramic composite thin plate vibrator. Especially, the characteristics of vibrating displacement of the vibrator are important for the fabrication of USM. So, in this study, we tried to analyze them by the FEM(finite element method) simulation program. ANSYS 5.6 we used is a finite element software enabling the analysis of 2 or 3 dimensional structure of piezoelectric materials. Using this made us analyzing the resonance frequency and calculating displacement of vibrator and then the position of the projection.n.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.6
• /
• pp.966-971
• /
• 2008

Free-piston engine system is a new type energy converter which uses a linear motion of piston by using linear generator. In free-piston engine system, the piston is not connected to a crank-shaft. The major advantages of free-piston engine system are high efficiency and low mechanical loss from the absence of motion conversion devices. Linear generator of free-piston engine system is used as generator and starting motor. In design step, considering of back-emf and detent force characteristics for generating mode and thrust and control characteristics for starting mode is needed. In this research, generating mode of flat-type linear generator and tubular-type linear generator is analyzed by finite element analysis method and starting mode of both type linear generators is analyzed by using capability curve. Capability curve is plotted from electrical parameters of both type linear generator and motion profile is calculated from mechanical parameters.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.585-588
• /
• 2002

The USM uses friction between a mobile part (rotor) and a vibration part(stator), which is different from the principle of the conventional motor based on the interaction of electric and magnetic fields. In this thesis, a flat-type $L_1-B_8$ mode USM was designed and fabricated the characteristics of an ultrasonic vibration. The results of fabricated USM are as follows: (1) In case of ultrasonic motor with elastic-body of stainless, when applied voltage, frequency, pressing force of rotor were 50 [V], 27.9 [kHz], 1.5 [N], 5.0[mN m] respectively, the speed of revolution could be presented up to 0 [cm/s]. (2) In case of ultrasonic motor with elastic-body of brass, when applied voltage, frequency, pressing force of rotor were 50 [V], 21.4 [kHz], 1.5 [N], 1.4[mN m]respectively, the speed of rotor revolution was presented up to 0 [cm/s]. (3) The USM of elastic-body of stainless showing 1.17[%], somewhat low, in the maximum efficiency according to torque was superior to the USM of elastic-body of brass showing 0.34 [%]. The Flat-type $L_1-B_8$ mode USM had characteristics of typical drooping torque-speed, large torque and high speed, and operating in both directions by phase reversal.