• 대한금속재료학회지
• /
• 제49권2호
• /
• pp.174-179
• /
• 2011

We investigated the surface morphology changes of a lithium/sulfur battery using multi-walled canbon nanotube added sulfur electrode during charge-discharge cycling. The Li/S cell showed the first discharge capacity of 1286 mAh/g-S, which utilized is 71% of the theoretical value. It decreased to 328 mAh/g-S at the 100th cycle, which corresponds to about 19% utilization of the total sulfur in the cathode. The spherical lumps of the reaction product were observed on the surface of the sulfur electrode. This material was verified as lithium sulfide by X-ray diffraction measurement. The pores in the separator were filled with reaction product. Thus the diffusion of the $Li^+$ ion decreased, which resulted in the decreased capacity of the Li/S cell.

• Korean Chemical Engineering Research
• /
• 제57권6호
• /
• pp.868-873
• /
• 2019

본 연구에서는 유기물인 메틸 바이올로겐(methyl viologen, MV)과 템폴(4-hydroxy-TEMPO, TEMPOL)을 활물질로 사용하고 NaCl의 중성 전해질 기반 수계 유기 레독스 흐름전지 성능이 멤브레인에 따라 어떻게 영향을 받는지 분석하였다. 메틸 바이올로겐(MV)과 템폴(TEMPOL)은 중성 전해질인 염화나트륨(NaCl) 전해질에 대해 높은 셀전압(1.37 V)을 얻을 수 있다. 성능 비교를 위해 사용한 멤브레인은 두 가지이다. 첫째로, 상용 양이온 교환막 중 하나인 Nafion 117를 사용하였을 때 성능은 첫번째 사이클에서 충전만 일어났을 뿐 그 후 높은 저항 때문에 완전지가 작동하지 않았다. 하지만 두번째로 사용한 Fumasep 음이온 교환막(FAA-3-50)은 Nafion 117 멤브레인을 사용했을 때와는 다르게 비교적 안정적인 충방전 사이클링을 보였다. 전류 밀도 $40mA{\cdot}cm^{-2}$, 컷-오프 전압 0.55~1.7 V에서 전류 효율(charge efficiency)은 97%, 전압 효율(voltage efficiency)은 78%로 높게 나타났다. 방전 용량(discharge capacity)은 10사이클에서 $1.44Ah{\cdot}L^{-1}$로 이론 용량($2.68Ah{\cdot}L^{-1}$)의 54%를 나타내었다. 방전 용량의 용량 손실율(capacity loss rate)은 $0.0015Ah{\cdot}L^{-1}/cycle$ 로 나타났다. 순환주사전류 실험을 통해 Nafion 117 멤브레인과 Fumasep 음이온 교환막 사이의 이러한 성능차이는 활물질의 크로스 오버(cross over) 현상으로 인한 방전 용량 손실이 아닌 멤브레인과 활물질의 화학적 반응으로 인한 저항 증가가 원인임을 파악할 수 있었다.

• 상하수도학회지
• /
• 제19권4호
• /
• pp.462-472
• /
• 2005

This study was carried out to suggest the plans for installation of rural sewage treatment facilities through the analysis of these facilities installed in Chungchongnam-do Province. About 5% of all installation was carried out by the department of wastewater and related environment problems and the other case was carried out by the department of construction or residence. In wastewater caused by 250 and 300 persons, facilities capacity do not exceed about $50m^3/d$, caused by 2,500 and 3,000 persons, $500m^3/d$. Advanced sewage treatment process were first needed in the discharge area where affected the water environment greatly. However, in carrying out the water quality pollutant of the total amount management system in the other areas, they should be driven only over the scale of pollutant quota object facilities standard. Rural sewage must be included in the special accounts according to the regulations of local government, and sewage treatment cost should be collected to manage. Installation type uses integrating joint treatment method in case the distance among villages is short or one treatment facility independently.

• Journal of Electrochemical Science and Technology
• /
• 제11권4호
• /
• pp.384-391
• /
• 2020

Due to its characteristics of light weight, high energy density, good safety, long service life, no memory effect, and environmental friendliness, lithium-ion batteries (LIBs) are widely used in various portable electronic products. The capacity and performance of LIBs largely depend on the performance of electrode materials. Therefore, the development of better positive and negative materials is the focus of current research. The application of metal organic framework materials (MOFs) derivatives in energy storage has attracted much attention and research. Using MOFs as precursors, porous metal oxides and porous carbon materials with controllable structure can be obtained. In this paper, rod-shaped Co-MOF-74 was grown on Ni Foam (NF) by hydrothermal method, and then Co-MOF-74/NF precursor was heat-treated to obtain rodshaped Co₃O₄/NF. Ni Foam was skeleton structured, which effectively relieved. The change of internal stress changes and destroys the structural volume of the electrode material and reduces the capacity attenuation. Co₃O₄/NF composite material has a specific discharge capacity of up to 1858 mA h/g for the first time, and a reversible capacity of up to 902.4 mA h/g at a current density of 200 mA/g, and has excellent rate and impedance performance. The synthesis strategy reported in this article opens the way to design high-performance electrodes for energy storage and electrochemical catalysis.

• 전기화학회지
• /
• 제23권1호
• /
• pp.11-17
• /
• 2020

프러시안 블루 유사체(Prussian blue analogue)중 가격이 낮은 철(Fe)을 기반으로 하는 Fe₂(CN)₆와 Na_xFe₂(CN)₆를 침전법으로 합성하여 리튬이온 이차전지용 양극재료로 사용하고자 하였다. Fe₂(CN)₆는 34.6 mAh g^-1의 낮은 가역용량을 발현하였으나, 소듐이 포함된 Na_xFe₂(CN)₆는 방전을 먼저 진행하는 경우에 107.5 mAh g^-1의 가역용량을 나타내고, 충전을 먼저 진행하여 구조 내의 소듐을 제거한 후에 사용하는 경우에는 더 높은 용량인 114.1 mAh g^-1의 가역용량을 발현하였으며 사이클 수명도 더욱 향상되었다. 그리고, Na_xFe₂(CN)₆의 합성과정에서 0℃, 상온, 60℃의 각각 다른 반응온도를 적용하여 합성하였다. 합성온도에 상관없이 Na_xFe₂(CN)₆는 유사한 초기 가역용량을 나타내었으나, 낮은 온도에서 합성된 경우일 수록 결정자의 크기가 작게 형성되었고, 향상된 사이클 수명을 나타내었다. 0℃에서 합성된 시료의 경우가 가장 사이클 수명이 우수하여 120번째 사이클에서 86.4 mAh g^-1의 용량을 나타내며 초기용량의 76.8%를 유지하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1034-1038
• /
• 1995

The purpose of this study is to research and develop $TiS_2$ composite cathode for lithium polymer battery(LPB). $TiS_2$ electrode represent a class of insertion positive electrode used in Li secondary batteries. In this study, we investigated preparation of $TiS_2$ composite cathode and AC impedance response of $TiS_2$ composite/SPE/Li cells as a function of state of charge(SOC) and cycling. The resistance of B type cell using $TiS_2PEO_8LiClO_4PC_5EC_5$ composite cathode was lower than that of A type cell using $TiS_2PEO$ composite cathode. The cell resistance of B type cell is high for the first few percent discharge, decreases for midium discharge and then increases again toward the end of discharge. We believe the magnitude of the cell resistance is dominated by passivation layer impedance and small cathode resistance. AC impedance results indicate that the cell internal resistance increase with cycling, and this is attributed to change of passivation layer impedance with cycling. The passivation layer resistance($R_f$) of B type cell decreases for the 2nd cycling and then increases again with cycling. Redox coulombic efficiency of B type cell was about 141% at 1st cycle and 100% at 12th cycle. Also, $TiS_2$ specific capacity was 115 mAh/g at 12 cycle.

• Bulletin of the Korean Chemical Society
• /
• 제34권2호
• /
• pp.433-436
• /
• 2013

Carbon-coated $Li_3V_2(PO_4)_3-LiMnPO_4$ composite cathode materials are first reported in this work, prepared by the mechanochemical process with a complex metal oxide as the precursor and sucrose as the carbon source. X-ray diffraction pattern of the composite material indicates that both olivine $LiMnPO_4$ and monoclinic $Li_3V_2(PO_4)_3$ co-exist. We further investigated the electrochemical properties of our $Li_3V_2(PO_4)_3-LiMnPO_4$ composite cathode materials using galvanostatic charging/discharging tests, where our $Li_3V_2(PO_4)_3-LiMnPO_4$ composite electrode materials exhibit the charge/discharge efficiency of 91.9%, while $Li_3V_2(PO_4)_3$ and $LiMnPO_4$ exhibit the efficiency of 87.7 and 86.7% in the first cycle. The composites display unique electrochemical performances in terms of overvoltage and cycle stability, displaying a reduced gap of 141.6 mV between charge and discharge voltage and 95.0% capacity efficiency after $15^{th}$ cycles.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.387-390
• /
• 1999

To improve the cycle performance LiM $n_2$ $O_4$as the cathode of 4V class lithium secondary batteries, the cathode properties of the cubic spinel phases LiM $g_{x}$ /M $n_{2-x}$/ $O_4$ synthesized at 80$0^{\circ}C$ were examined. All cathode material showed spinel phase based on cubic phase in X-ray diffraction however. other peaks gradually exhibited and became intense with the increase of x value in LiM $g_{x}$ /M $n_{2-x}$/ $O_4$. The cycle performance of the LiM $g_{x}$ /M $n_{2-x}$/ $O_4$was improved by the substitution of $Mg^{2+}$ for M $n^{3+}$ in the octahedral sites. Specially LiM $g_{0.1}$/M $n_{1.9}$ / $O_4$cathode materials showed the charge and discharge capacity of about 130~125mAh/g at first cycle and about 105mAh/g after 50th cycle. It is excellent than that of pure LiM $n_{2}$/ $O_4$ which 125mAh/g at first cycle 70mAh/g at 50th. In addition cathode material prepared at 80$0^{\circ}C$ for 24hr and 42hr in the charge and discharge capapcity as well as the cycle stability.ility.y.y.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 춘계학술대회 논문집
• /
• pp.74-77
• /
• 1997

We have examined conduction properties and electrochemical properties of MCMB 6-28 and MPCF 3000. As results, electrical conductivity of carbon decreased with increasing the number of intercalated lithium ion. MCMB and MPCF showed reversible redox reaction, and the potentials of the oxidized and reduced peaks were 0.3V and 0V, respectively. First discharge capacity of MCMB was 190㎃f/g and that of MPCF was 220㎃h/g. MPCF has good properties for lithium secondary battery.

• 전기화학회지
• /
• 제10권2호
• /
• pp.88-93
• /
• 2007

Nano-sized Sn particles were coated with Ni-P layer using an electroless deposition method and their anodic performance was tested for lithium secondary batteries. Uniform coating layers were obtained, of which the thickness was controlled by varying the $Ni^{2+}$ concentration in the plating bath. It was found that the Ni-P layer plays two important roles in improving the anodic performance of Sn powder electrode. First, it prevents the inter-particle aggregation between Sn particles during the charge/discharge process. Second, it provides an electrical conduction pathway to the Sn particles, which allows an electrode fabrication without an addition of conductive carbon. A pseudo-optimized sample showed a good cyclability and high capacity ($>400mAh\;g^{-1}$) even without conductive carbon loading.