• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2007년도 제34회 KOSCO SYMPOSIUM 논문집
• /
• pp.176-183
• /
• 2007

An experimental study was performed to investigate the effects of mixing quality, inlet pressure, nozzle diameter on CO emission and radiation characteristics in porous ceramic fiber radiant burners. Observations of combustion characteristics occurring inside the burner system which was insulated fiber mat, were investigated by measuring temperature, CO emission and radiation characteristics. Combustion was achieved at the firing rate of $88{\sim}99$ kcal/hr, inlet pressure of $100{\sim}250$mm$H_2O$. CO emissions were found to be strongly dependent on the operating conditions. There was a tendency that CO concentration increased as the firing rate increases. The reason for rise of CO concentration is that it becomes the relatively rich condition. The fiber burner exhibit significant both spectral intensity peaks in the bands at 2.5${\mu}m$ and 4.0${\mu}m$ relatively, There is a small difference in the variable mixing tube. However spectral intensity increased with the firing rate.

• 항공우주기술
• /
• 제6권2호
• /
• pp.141-149
• /
• 2007

재생냉각과 막냉각 그리고 열차폐 코팅이 적용된 재생냉각 축소형 연소기를 이용하여 연소시험을 수행하였다. 시험결과 적용된 냉각 방식은 설계 조건에서 그 역할을 충실히 수행하였으나 연료 매니폴드 내에 삽입된 구조 보강용 링에 의한 연료 유동의 불안정성으로 인해 고주파 연소불안정이 발생하였다. 연료 유동의 불안정성은 삽입 링을 제거함으로써 개선되었고 추가 연소시험을 통해 수정된 연소기의 연소안정성을 검증할 예정이다.

• Food Science and Biotechnology
• /
• 제18권5호
• /
• pp.1212-1217
• /
• 2009

This study examined the influence of manufacturing processes and extraction conditions on the chemical compositions of green tea. Green tea samples grown in various areas (Korea, China, and Japan) and processed by 4 different methods (steaming, pan-firing, steaming and pan-firing, and heavy roasting after steaming and pan-firing) were collected for study. The chemical compositions of the green tea extracts and infusions were different according to their processing methods and extraction conditions, including catechins, caffeine, and free amino acids contents. In all samples analyzed, (-)-epigallocatechin gallate (EGCG), (-)-epigallocatechin (EGC), and theanine were determined as the major catechins and free amino acid, respectively. Studies of samples grown in the same area (Jeju; Korea) showed that there were significant differences in the concentrations of catechins and caffeine in extract and infusion according to the processing methods. These results indicate that processing methods influenced the chemical compositions of the green tea extracts and infusions.

• 한국추진공학회지
• /
• 제11권2호
• /
• pp.62-70
• /
• 2007

지향성능은 발사차량의 정확성에 있어서 중요한 요소이다. 본 연구는 외란 가속도를 이용하여 지향구조물의 진동을 감지하는 방안과 실험 결과에 대하여 기술하였다. 주행 중 발생하는 진동 경향을 분석하기 위하여 가속도 자료를 이동평균과 힐버트 변환을 이용하여 신호 처리하였다. 다양한 외란에 대하여 가속도의 모드 계수를 얻었으며, 차량속도, 노면조건, 지향구조물의 특성을 차량 동특성의 진동을 변화시키는 요소로 간주하였다. 마지막으로 다양한 주행 조건의 진동 신호를 분류하기 위한 패턴인식에 역전파 신경망 이론을 이용하였다. 각 조건에 대하여 실험 결과를 비교 분석하였다.

• 한국세라믹학회지
• /
• 제33권9호
• /
• pp.1003-1011
• /
• 1996

Hydroxyapatite powder was synthesized by a citrate method, . Char-like precursor composed of Ca8(HPO4)2(PO4)4.5H2O (OCP) and CaCo3 was found via viscous resin-like intermediate by heating the mixed aqueous solution of Ca(NO3)2.4H2O(NH4)2HPO4 and citric acid. Resulted powder was transformed into hydroxyapatite phase by firing over 120$0^{\circ}C$-135$0^{\circ}C$ for 4 hr using the powder calcined at 90$0^{\circ}C$ for 10 hr composed of mostly single hydroxyapatite phase. The sintered densities increased with firing temperature up to 130$0^{\circ}C$ but the highest relative density was about 94% of theoritical value. indicating the presence of closed pores. The maximum 96 MPa of flexural strength was obtained at 120$0^{\circ}C$ firing but the flexural strength showed lower values over the above sintering condition. Vitro test was performed by immersing of two jointed specimens in SBF for seven days and adhesion was observed between two specimens.

• 조명전기설비학회논문지
• /
• 제12권1호
• /
• pp.85-92
• /
• 1998

본 논문에서는 페트리 네트로 記述된 제어 사양을 접속 행렬로 해석한 후, 그 결과를 근거로 병렬 시퀸스의 수행이 가능한 순차 시스템 제어기(Sequential System Controller)를 설계하였다. 순차 시스템 제어기는 입력 처리부, 그리고 점화 처리부와 토큰 제어기로 구성된 페트리 네트 제어기로 구성된다. 입력 처리부에서는 입력 신호를 선택하여 점화 처리부로 전달하며, 점화 처리부는 토큰 운전기의 토큰 상태에 따라서 입력된 신호의 점화 여부를 판단하게 된다. 제안된 제어기는 제어 사양의 변경시 접속 행렬을 저장한 롬의 내용 변경만으로 제어기의 변경이 가능하고, 페트리 네트 제어기의 모듈화가 가능하여 기능의 확장이 용이하므로 자동창고 시스템, 반송 시스템, 및 승강기 시스템과 같은 순차 시스템 제어기의 개발 및 실현을 용이하게 할 수 있다.

• Tribology and Lubricants
• /
• 제35권4호
• /
• pp.244-266
• /
• 2019

The purpose of this study is to estimate the wear volumes of engine journal bearings operating at variable angular velocity of a shaft in the beginning of firing start-up cycle. To do this, first we find the potential region of wear scar on engine journal bearings where the applied bearing load and crank shaft velocity are variable. The potential wear regions are discovered by finding minimum oil film thickness at every crank angle existing below most oil film thickness scaring wear (MOFTSW) obtained based on the concept of the centerline average surface roughness. Then we calculate the wear volume from the wear depth and two wear angles decided by the magnitude of each film thickness lower than MOFTSW at every crank angle. The results show that the expected wear region is located at a few bearing angles after and/or behind the upper center of a big-end bearing and the lower center of a main bearing. And the real wear region is similar to the estimated wear region. Further we find that the wear scar on an engine journal bearing may occur at re-starting time after switch-off of a start motor especially under the condition of high oil temperature.

• 헤리티지:역사와 과학
• /
• 제33권
• /
• pp.4-35
• /
• 2000

The paddling technique is a Kind of secondary treatments in the process of ceramic forming, which appeared in the Chinese Neolithic Age pottery making. In the case of Korean prehistoric pottery making, it was first introduced together with the kiln firing method from Tongpei region(東北地方) of China in Yan(燕) dynasty occupation period. Korean archaeologists have recognized the adoption of the new technologies as a drastic innovation of ceramic production. And most of them have thought that the diffusion of new techniques, accompanied by the migration of the northern ethnic groups, had been immediately followed by the innovative changes in pottery procdution. However, rejecting the arguments from the simple diffusionist viewpoint, I have first tried to describe the innovation processes in the ceramic production systems as a spatio-temporal process. The paddling technique by the cord-wound paddle, which was first introduced among the various paddles, was associated with the new sort of pottery, round pots fired in low temperature of reducing atmosphere condition. The cord-marked round pots first tried by the indigenous potters in the southern part of Korean were characterized by the relatively low leveled techniques in forming and firing, compared to those of north-east China. The techniques of the round pots were hardly improved in the domestic production system until the appearance of the fully-specialized one. The specialized production system of the round pot, which appeared first in the mid-western region of Korea, showed the diversified paddling techniques and made the noticeable improvements in forming and firing processes.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2000년도 춘계총회,특별강연,심포지움,연구발표회
• /
• pp.83.1-83.1
• /
• 2000

• Journal of Advanced Marine Engineering and Technology
• /
• 제19권3호
• /
• pp.50-61
• /
• 1995

In recent years, many ceramic researchers have discoved various methods of joining ceramic to metal. However, most of these joining methods are perfomed under vacuum and pressured circumstances. So, when we join ceramic to metal,the proceedings are very complicated and require a very high cost. The purpose of this study is to develop a new joining method of an alumina ceramic to an aluminum metal in air atmosphere. The joining condition, such as copper metallizing, nickel plating, brazing, etc. was investigated through the shear strength test of the trial joint. The results obtained from the above experimenta are summarized as follows : 1) In the case of the $Al_2O_3$/$Al_2O_3$joint, the shear strength of the joint was affected by the various foctor such as kaolin content, copper metallizing thickness, firing temperature, firing time. 2) The better shear strength of the $Al_2O_3$/Al joint was obtained when Ni plating was conducted under higher current density than existing plating condition. 3) The shear strength of the $Al_2O_3$/Al joint increases with the Ni plating thickness is confined to the range of this paper. 4) The shear strength of the thermal-shocked specimen($Al_2O_3$/Al joint) was far more deteriorated than that of the as-bonded specimen.