• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.421-422
• /
• 2008

In this paper, CMOS RF front-end circuits for an L1/L5 dual-band global positioning system (GPS)/Galileo receiver are designed in $0.13\;{\mu}m$ CMOS technology. The RF front-end circuits are composed of an RF single-to-differential low noise amplifier, an RF polyphase filter, two down-conversion mixers, two transimpedance amplifiers, a IF polyphase filter, four de-coupling capacitors. The CMOS RF front-end circuits provide gains of 43 dB and 44 dB, noise figures of 4 dB and 3 dB and consume 3.6 mW and 4.8 mW from 1.2 V supply voltage for L1 and L5, respectively.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.8
• /
• pp.42-51
• /
• 1998

An 8th-order elliptic low-pass filter with cutoff frequency of 3.13kHz is presented. The design procedure is based on teh 1/s impedance transformation which is applied to a minimum capacitor LC ladder network.The tranformed network is implemented with resistors and high Q frequency-dependent negative resistors (FDNR's). The high Q FDNR is realized with two transadmittance amplifiers. Detailed SPICE simulations show that the iflter has pass-band ripple of 0.18dB, stop-band attenuation over 100dB, cutoff frequency of 3.13 khz, and cutoff frequency temperature coefficient of 8.5ppm/.deg. C at supply voltage of .+-.5V.

• Journal of electromagnetic engineering and science
• /
• v.6 no.4
• /
• pp.217-221
• /
• 2006

Multipactor-free S-band duplexer based on inter-digital cavity type filter is proposed and demonstrated by in-house mulitpactor test facility for satellite RF components. Multipactor sensitivity of designed duplexer is analyzed by checking it out the maximum field accumulated region inside duplexer and calculating the electric field intensities at each resonator using 3D EM simulation in order to restrict the minimum gap distance as 2.5 mm which handles 43.13 dBm RF input power. Multipactor threshold was finally detected at 44 dBm in experiment for pulse mode test. The developed multipactor test method is cost effective, simple structure and gives a good agreement compared with the previous high cost MP test methodologies.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.333-337
• /
• 2003

In this paper, 5.2 GHz WLAN BPF(Band Pass Filter) using LTCC(Low temperature co-firing ceramic) Multilayer technology was simulated and manufactured. A DGS(Defected Ground structure) resonator with spiral ground pattern is used to shorten resonator size and improve circuit Q factor. And the equivalent circuit of BPF was suggested. The measured result shows good agreement with simulated data. Experimental results show the center frequency of 5.25GHz, the insertion loss of 0.14dB, and the 3-dB bandwidth of 350MHz (6%). The center frequency of BPF is 5.25GHz which is available for wireless LAN.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.487-488
• /
• 1995

Broadband Microwave Low Noise Amplifier(LNA) is designed. The matching method using the broadband BPF(BandPass Filter) is introduced in this paper. This method is that the filter having the same reflection coefficient of Microwave GaAs FET in the desired bandwidth is located on the input stage of FET. The Simulated results is obtained that the $S_{21}$ and noise figure in 2.5GHz$\sim$9GHz, band are 8.5dB $\pm$ 1.5dB, 2.5dB $\pm$ 0.3dB respectively.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.10
• /
• pp.1900-1907
• /
• 2010

In this paper, a recurrent cerebellar modulation articulation control with praticle swarm optimization (PSO) method has been investigated for improvement of noise attenuation performance in active noise control system. For narrow band noise, FXLMS and RCMAC has a partial satisfactory noise attenuation. However, noise attenuation performance is poor for broad band noise and nonlinear path since it has linear filter structure. To improve this problem, a RCMAC with PSO is proposed and it is shown that satisfactory noise attenuation performance is obtained by some simulations in duct system using harmonic motor noise and KTX cabin noise as a noise source.

• International Journal of Control, Automation, and Systems
• /
• v.4 no.5
• /
• pp.592-600
• /
• 2006

The pattern recognition of the complicated grasping operation based on electroencephalography (simply named as EEG) is very helpful on realtime control of the robotic hand. In the paper, a new spectral feature analysis method based on Band Pass Filter (simply named as BPF) and Power Spectral Analysis (simply named as PSA) is presented for discriminating the complicated grasping operations. By analyzing the spectral features of grasping operations with the use of the two-channel EEG measurement system and the pattern recognition of the BP neural network, the degree of recognition by the traditional spectral feature method based on FFT and the new spectral features method based on BPF and PSA could be compared. The results show that the proposed method provides highly improved performance than the traditional one because the new method has two obvious advantages such as high recognition capability and the fast learning speed.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.7
• /
• pp.36-42
• /
• 1995

In this paper, the CAD program for designing the microwave waveguide narrow-band bandpass filters has been developed by the passband correction method with filter synthesis for the MDR(Microwave Digital Relay) system. Here, the modified double E-plane structures are employed in the filter structure which is analyzed by the variational method. Using the developed CAD program, 0.01dB equi-ripple chebyshev type 6-section bandpass filters used in the MDR system operating nationally is designed at the center frequency of 11.0GHz, fabricated with tunable type and then measured by tuning process. The experimantal results show good agreements with the theoretical results.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.3127-3129
• /
• 2000

본 논문에서는 광 다이오드에서 들어오는 신호로부터 원하는 대역의 신호를 얻기 위한 적외선 수신 IC에 적합한 대역통과필터를 설계하였다 설계한 대역통과필터는 2차 Biquad gm-C 필터의 구조를 이용하여 중심주파수가 38kHz. Quality factor가 10인 필터를 구현하였다. 구현된 대역통과필터는 필터부분과 중심주파수를 보정해 주는 frequency tuning 부분으로 구성되어 있다. 낮은 transconductance와 높은 선형성을 요구하는 transconductor의 설계를 위해 Gilbert 곱셈기 특성을 이용하여 구현하였고 AMS사의 0.8${\mu}m$ BiCMOS model을 사용하여 +5V로 동작되도록 설계 하였다

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.05a
• /
• pp.134-137
• /
• 2002

A new LTCC material in the $PbWO_4-TiO_2-B_2O_3-CuO$ system was developed. The developed material can be sintered at $850^{\circ}C$ and its dielectric properties are $\varepsilon_r=20-25, Q\timesf_o=30000~50000GHz$ , and $\tau_f=0.2~30ppm/^{\circ}C$, depending on the components moi ratio. Due to its low sintering temperature and microwave dielectric properties, the developed material can be used as a LTCC substrate for fabrication of multilayered microwave communication module set. In present study, using this material, tape casting condition was established. With this processing condition, a T-resonator was fabricated and its electrical properties were examined. Also, a 2-Pole band pass filter was fabricated and its frequency characteristics were compared with simulation results.