• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.11 s.353
• /
• pp.77-82
• /
• 2006

Analog channel selection filter is described which is designed for a direct-conversion receiver of a IEEE 802.11a wireless LAN. The channel selection filter is an active-RC fifth-order Chebyshev filter with 10MHz cut-off frequency. Two-stage operational amplifier of the filter employs a current re-using feedforward frequency compensation scheme to minimize the power consumption. The filter has been implemented in a 0.18mm CMOS technology and the experimental results show 20mW power consumption with 1.8V supply voltage and 19dB out-of-band iIP3.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.991-996
• /
• 2001

It is well known that there are two experimental errors on acoustic decay measurements. One is due to the influence of the band pass filter the other one is that of an averaging device. In this paper the influence of the filter is in detail investigated. To minimize the influence of filter, the product of the filter bandwidth Β (3㏈ bandwidth) and the reverberation time T$\sub$60/ of the room under test is at least 16. Moreover, if the initial part of an acoustic decay curve is important, the strong requirement, i.e. BT$\sub$60/＞ 64, must be satisfied. In this paper, the wavelet filter bank instead of the band pass filter bank is applied to obtain an acoustic decay curve. As results, the influence of filter is reduced and then the value of BT$\sub$60/ required for obtaining an acceptable decay curve is at least 4. The strong requirement for the initial part of a decay curve is also replaced by the BT$\sub$60/＞ 16 instead of BT$\sub$60/＞ 64.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.9
• /
• pp.679-691
• /
• 2003

The band-width of disk drive servo system is rapidly increasing for the robustness to external disturbance as the track density is increasing. The increase of the band-width may cause mechanical resonance of an actuator. In disk drive servo system, a notch filter is usually used to suppress the mechanical resonance of the actuator. However, the resonance frequency differs from drive to drive because of manufacturing tolerance and varies with temperature even within a single drive. The variation of resonance frequency degrades the suppression performance of the notch filter. In this paper, we present an adaptive digital notch filter that identifies the resonance frequency of the disk drive servo actutaor precisely and adjusts automatically its center frequency. For this, we design an adaptive FIR digital filter for the estimation of the resonance frequency. The estimation filter identifies the resonance frequency adaptively using the output signal generated from the servo system, which is excited with an excitation signal including all the expected resonance frequency components. We prove mathematically the convergence of the resonance frequency estimation filter. Furthermore, in order to demonstrate the practical use of our work, we present some experimental results using a commercially available disk drive.

• Journal of Advanced Navigation Technology
• /
• v.22 no.1
• /
• pp.27-30
• /
• 2018

In this study, a 40 GHz band pass filter(BPF) employing a hair-pin structure has been designed, fabricated, and characterized for millimeter-wave wireless communication applications. Using the 3 dimensional(3-D) electromagnetic(EM) tool and design equations of the hairpin BPF, the BPF was desgned on the 5 mil-thick Duroid substrate(RT5880) with a relative dielectric constant (${\varepsilon}_r$) of 2.2. The tapping point (t) of the U-shape resonator in the input and output port has been determined using extracted an external Q-factor ($Q_e$). The coupling coefficients between the other resonators are calculated by adjusting the physical dimensions for the desired response of the BPF. The fabricated BPF was characterized using probing method on a probe station. Its measured center frequency(fc) and fractional BW are 41.6 GHz and 7.43 %, respectively. The measured return loss is below -10 dB at the pass band and the insertion loss is 3.87 dB. The fabricated BPF is as small as $9.1{\times}2.8mm^2$.

• Journal of the Korean Ceramic Society
• /
• v.39 no.2
• /
• pp.210-215
• /
• 2002

Optical Band-pass Filter(BPF) for the selected wavelength of 4300 nm was designed and fabricated on Si wager by alternately depositing Ge and $SiO_2$ thin layers by an electron beam evaporation technique. The fabricated BPF showed the optical transmittance characteristics of 58.2% with FWHM(Full Width at Half Maximum) of 204 nm at 4300 nm, but showed the transmittance less than 5% due to the reflectance over all the wavelength ranges except 4300 nm band. The $CO_2$ sensitivity of BPF was investigated with the transmittance as a function of $CO_2$ gas concentration using a sensing cell attached to FT-IR instrument. The transmittance of BPF was almost linearly decreased with increasing of $CO_2$ concentration in the range of from 500 to 5000 ppm. The sensing structure using double BPFs showed higher slop of transmittance vs $CO_2$ concentration, and thus higher gas sensitivity than that using a single BPF, even though the former had relatively lower transmittance.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.9
• /
• pp.904-911
• /
• 2011

This paper deals with transmission characteristics of a new dual resonant structure for designing waveguide band-pass filter. The structure which has a pass-band between two adjacent stop-bands in a single body consists of circular ridged aperture and four armed conducting patch. The dual resonant behavior of the structure can be represented by a combination of LC series and parallel resonant circuits. Also these resonant properties can be easily controlled by varying the geometry of the aperture and four armed conducting patch. Actually, the structure is fabricated on the microstrip substrate by use of etching technique so that it is formed an iris type resonator which can be easily put into the transverse plane of the waveguide. We use WR-90 standard waveguide, adapters, and VNA(vector network analyzer) to measure the resonant characteristics of the structure. It is very useful to design and to improve the cutoff skirts characteristics in the waveguide band-pass filter design area.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.12
• /
• pp.21-30
• /
• 1999

Several kinds of design method for the hairpin type band-pass filter have been reported. The conventional design methods have some restrictions in characteristic impedance of coupled line section, which provide complexities to designer. In this paper, the novel design formulas for the hairpin type band pass filter have been derived and proposed to resolve the problems of the reported design methods. By employing the equivalent circuit of the coupled line section and band pass filter design theory, the design procedures and formulas are derived. The hairpin type RX/TX band pass filters for the IMT-2000 service have been designed, fabricated with duplexer configuration, and then measured to show the validity of the proposed design method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.4
• /
• pp.988-996
• /
• 1998

BN ceramics with 0.07wt% $V_{2}O_{5}$ and 0.03wt% CuO(BNC3V7) sintered at $900^{\circ}C$ where it is possible for these to be co-fired with Ag electrode. Dielectricconstant of 44.3, TCF of 22 ppm$/^{\circ}C$ and $Qxf_{o}$ value of 22,000 GHz can be obtained from BNC3V7, multilayer type band pass filters using tapped method and conventional method were designed for PCS (Personal Communication System) applications. Tapped method by adopting input/output-tapping scheme the chip filter stucture becomes simpler and needs fewer layers than that using the conventional input/output-coupling scheme. A multilayer type band pass filter fabricated by screen-printing with silver electrode after tape casting. The simulated characteristics of the fabricated filters sintered at $900^{\circ}C$ were compared with the designed ones. Even though the centered frequencies of tapped and conventional band pass chaip filters were measured to shift about 90MHz downward, the band pass characteristics of both filters were similar that of designed ones. The spuriousresonance characteristic of tapped pass chip filter was better than that of conventional chip filer.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.12
• /
• pp.1402-1407
• /
• 2007

This paper presents a new design method of the Ultra-Wide-Band BandPass Filter using the CRLH-TL(Composite Right- and Left-Handed Transmission-line) having the Metamaterials' properties. Instead of the periodic type or many cells of the CRLH-TL, only the unit cell is used to miniaturize the target component, which can not be realized by the conventional quarter guided-wavelength resonator-based filters. Particularly, the strong coupling essential to the Ultra Wide Band is enabled by the interdigital coupled lines between the grounded stubs. The proposed design scheme is validated by the electromagnetic simulation and measurement of the fabricated filter which shows the total size of 'the guided-wavelength/9.4', the 100 % fractional bandwidth for the UWB, the insertion loss of less than 1 dB and the flat group-delay.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.7
• /
• pp.10-16
• /
• 2012

In this paper, we tried to realize a next generation MILES detection system which is robust to optical noise using a narrow band interference optical filter. Applying a narrow band interference optical filter which has the wavelength range of 895~915nm to the LASER wavelength of 900nm, we could obtain detection characteristics robust to strong optical noise which can be occurred in street battles. However, the MILES detection system has the blind range of detection in the incident angle range of $30^{\circ}{\sim}90^{\circ}$. To solve this problem we proposed a method of incident angle scatter using refractors. Applying a concave meniscus lens refractor which has diopter of 5.4 to the MILES detection system, we could eliminate the blind angle of detection.