• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.215.2-215.2
• /
• 2015

We fabricated dual active layer (DAL) thin film transistors (TFTs) with indium tin zinc oxide (ITZO) and indium gallium zinc oxide (IGZO) thin film layers using solution process. The ITZO and IGZO layer were used as the front and back channel, respectively. In order to investigate the bias stress stability of ITZO SAL (single active layer) and ITZO/IGZO DAL TFT, a gate bias stress of 10 V was applied for 1500 s under the dark condition. The SAL TFT composed of ITZO layer shows a poor positive bias stability of ${\delta}VTH$ of 13.7 V, whereas ${\delta}VTH$ of ITZO/IGZO DAL TFT was very small as 2.6 V. In order to find out the evidence of improved bias stress stability, we calculated the total trap density NT near the channel/gate insulator interface. The calculated NT of DAL and SAL TFT were $4.59{\times}10^{11}$ and $2.03{\times}10^{11}cm^{-2}$, respectively. The reason for improved bias stress stability is due to the reduction of defect sites such as pin-hole and pores in the active layer.

• Journal of Sensor Science and Technology
• /
• v.16 no.2
• /
• pp.85-90
• /
• 2007

This paper presents the growth conditions and characteristics of polycrystalline 3C-SiC (silicon carbide) thin films for M/NEMS applications related to harsh environments. The growth of the 3C-SiC thin film on the oxided Si wafers was carried out by APCVD using HMDS (hexamethyildisilane: $Si_{2}(CH_{3})_{6})$ precursor. Each samples were analyzed by XRD (X-ray diffraction), FT-IR (fourier transformation infrared spectroscopy), RHEED (reflection high energy electron diffraction), GDS (glow discharge spectrometer), XPS (X-ray photoelectron spectroscopy), SEM (scanning electron microscope) and TEM (tunneling electro microscope). Moreover, the electrical properties of the grown 3C-SiC thin film were evaluated by Hall effect. From these results, the grown 3C-SiC thin film is very good crystalline quality, surface like mirror and low defect. Therefore, the 3C-SiC thin film is suitable for extreme environment, Bio and RF M/NEMS applications in conjunction with Si fabrication technology.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.4
• /
• pp.207-212
• /
• 2014

Aluminum-doped zinc oxide (AZO) films were deposited on SiOC/Si wafer by an RF-magnetron sputtering system, by varying the deposition parameters of radio frequency power from 50 to 200 W. To assess the correlation of the optical properties between the substrate and AZO thin film, photoluminescence was measured, and the origin of deep level emission of AZO thin films grown on SiOC/Si wafer was studied. AZO formed on SiOC/Si substrates exhibited ultraviolet emission due to exciton recombination, and the visible emission was associated with intrinsic and extrinsic defects. For the AZO thin film deposited on SiOC at low RF-power, the deep level emission near the UV region is attributed to an increase of the variations of defects related to the AZO and SiOC layers. The applied RF-power influenced an energy gap of localized trap state produced from the defects, and the gap increased at low RF power due to the formation of new defects across the AZO layer caused by lattice mismatch of the AZO and SiOC films. The optical properties of AZO films on amorphous SiOC compared with those of AZO film on Si were considerably improved by reducing the roughness of the surface with low surface ionization energy, and by solving the problem of structural mismatch with the AZO film and Si wafer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1993.11a
• /
• pp.112-115
• /
• 1993

We have studied a property of arachidic acid Langmuir-Blodgett films at room temperature with two different electrodes ; Al/LB/Al and Au/LB/Au. Since a natural oxide layer is formed on top of the Al electrode, the appropriate structure of AL/LB/Al is Al/Al$_2$O$_3$/LB/Al. To obtain a property of Pure LB film, Aua/LB/Au structure was made. In Al/Al$_2$O$_3$/LB/Al structure, a conductivity of 3.7${\times}$10$\^$-14/ S/cm was obtained by using current-voltage(I-V) characteristics. In Au/LB/AU structure, however, I-V curve was not able to be measured because of short current even in 51 layers of the LB film. A status of defects in the film was confirmed by copper decoration method. We have clearly seen a rather big difference of defect in those two above structures.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.500-503
• /
• 2003

We studied the nematic liquid crystal (NLC) aligning capabilities by the UV alignment method on a a-C:H thin film surface. A good LC alignment by UV exposure on the a-C.H thin film surface at 200 ${\AA}$ of layer thickness was achieved. Also, a good LC alignment by the UV alignment method on the a-C:H thin film surface was observed at annealing temperature of 180 $^{\circ}C$. However, the alignment defect of the NLC was observed above annealing temperature of 200 $^{\circ}C$. Consequently, the good thermal stability of LC alignment by the UV alignment method on the a-C:H thin film surface can be achieved.

• Electrical & Electronic Materials
• /
• v.8 no.3
• /
• pp.340-351
• /
• 1995

Electrical, physical and optical properties of Aluminum(Al), Copper(Cu) thin films were investigated in order to establish the optimum sputtering parameters in Liquid Crystal Display (LCD) panel applications. DC-magnetron sputtered film on coming 7059 samples were fabricated with variations of deposition power densities, deposition pressures and substrate temperatures. Low resistivity films(AI;2.80 .mu..ohm.-cm, Cu:1.84 .mu..ohm-cm),which lower than the reported values, were obtained under sputtering parameters of power density(250W), substrate temperature(450-530.deg. C) and 5*10$\^$-3/ Torr deposition pressure. Expected columnar growth and stable grain growth of both films was observed through the Scanning Electron Microscope(SEM) micrographs. Dependency of the applicable defect-free film density upon depositon power and temperature was also characterized. Not too noticable variations in X-ray diffraction patterns were remarked under the alterations of sputtering parameters. High optical reflectivities of Al, Cu films, approximately 70-90 %, showed high degree of surface flatness.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.3
• /
• pp.202-206
• /
• 2007

ZnO is a promising material to make high efficient ultraviolet(UV) or blue light emitting diodes(LEDs) because of its large binding energy and energy bandgap. In this study, we prepared ZnO thin films with p-type conductivity on silicon(100) substrates by RF magnetron sputtering in the mixture of $N_2$ and $O_2$. The process was accompanied by low pressure in-situ annealing in $O_2$ at $600^{\circ}C$ and $800^{\circ}C$ respectively. Hall effect in Van der Pauw configuration showed that the N-doped ZnO film annealed at $800^{\circ}C$ has p-type conductivity. Photoluminescence(PL) spectrum of the film annealed at $800^{\circ}C$ showed UV emission related to exciton and bound to donor-acceptor pair(DAP) as well as visible emission related to many intrinsic defects.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1996.06a
• /
• pp.121-147
• /
• 1996

Since 1980, the water quality of ultra-pure water has been rapidly improved, and presently ultra-pore water producing equipment for 64Mbit is in operation. Table 1 shows the degree of integration of DRM and required water quality exlmple. The requirements of the ultra-pure water for 64Mbit are resistivity: 18.2 MQ/cm or higher, number of particulates: 1 pc/ml or less (0.05 $\mu$m or larger). bacteria count: 0.1 pc/l or less. TOC (Total Organic Carbon, index of organic snbstance) : 1ppb or less, dissolved oxygen: 5ppb or less, silica: 0.5ppb or less, heavy metal ions: 5ppb or less. The effect of metals on the silicon wafer has been well known, and recently it has been reported that the existence of organic substance in ultra-pure water is closely related to the device defect, drawing attention. It is reported that if organic substance sticks to the natural oxidation film, the oxide film remaims on the organic substance attachment in the hydrofluoric acid treatment (removal of natural oxidation film). The organic substance forms film on the silicon wafer, and harmful elements such as metals and N.P.S., components contained in the organic substance and the bad effect due to the generatinn of silicon carbide cannot be forgotten. In order to remove various impurities in raw water, many technological develoments (membrane, ion exchange, TOC removal, piping material, microanalysis, etc.) have been made with ultra-pure water producing equipment and put to practical use. In this paper, technologies put to practical use in recent ultra-pure vater producing equimeut are introduced.

• The Korean Journal of Ceramics
• /
• v.3 no.1
• /
• pp.1-4
• /
• 1997

Diamond film (24$\mu\textrm{m}$) were prepared by Microwave Plasma Chemical Vapor Deposition method from a reactive CO/H$_2$ mixtures. Micro-Raman spectroscopy and micro-cathodoluminescence study were carried out along the crosssection and correlated to SEM observation. CL image of cross-section was also investigated. Peak position, FWHM of Raman spectrum were determined using Lorentzing fit. The stress in this sample is 0.4~0.7 GPa compressive stress, and along the distance the compressive stress reduced. The Raman peak broadening is dominated by phonon life time reduction at grain boundaries and defect sites. Defects and impurities were mainly present inside the film, not at Silicon/Diamond interface.

• Corrosion Science and Technology
• /
• v.7 no.1
• /
• pp.40-44
• /
• 2008

Passive metal forms an interfacial diffuse layer on the surface of passive film by its reaction with $H^+$ or $OH^-$ ions in solution depending on solution pH. There is a critical pH, called pH point of iso-selectivity ($pH_{pis}$) at which the nature of the diffuse layer is changed from the anion-permeable at pH<$pH_{pis}$ to the cation-permeable at pH>$pH_{pis}$. The $pH_{pis}$ for a passivated Fe was determined by examining the effects of pH on the thickness of passive film and on the dissolution reaction occurring on the passive film under a gavanostatic reduction in borate-phosphate buffer solutions at various pH of 7~11. The steady-state thickness of passive film formed on Fe showed the maximum at pH 8.5~9, and further the nature of film dissolution reaction was changed from a reaction producing $Fe^{3+}$ ion at $pH\leq8.5$ to that producing $FeO_2{^-}$ at $pH\geq9$, suggesting that the $pH_{pis}$ of Fe is about pH 8.5~9. In addition, the passive film formed at pH 8.5~9, $pH_{pis}$, was found to be the most protective with the lowest defect density as confirmed by the Mott-Schottky analysis. Pitting potential was decreased with increasing $Cl^-$ concentration at $pH\leq8.5$ due probably to the formation of anion permeable diffuse layer, but it was almost constant at $pH\geq9$ irrespective of $Cl^-$ concentration due primarily to the formation of cation permeable diffuse layer on the film, confirming again that $pH_{pis}$ of Fe is 8.5~9.