• Journal of Sensor Science and Technology
• /
• v.11 no.1
• /
• pp.9-17
• /
• 2002

The forming conditions of X-ray storage phosrhors $BaFBr_{1-x}I_x:Eu^{2+}$, $Na^+$ have been investigated, and measured the PSL emission spectra and its intensity, fading characteristics and does dependence of the prepared phosphors. These characteristics were compared with those of commercial image plate (ST-III) obtained from Fuji Photo Film Co. The optimal preparing conditions of $BaFBr_{1-x}I_x:Eu^{2+}$, $Na^+$ Phosphor were 0.5 mol% of $EuF_3$, 4.0 mol% of NaF and composition ratio x=0.3, and the sintering temperature were $950^{\circ}C$ in $H_2$ atmosphere. When the composition ratio x was equal to 0, the spectral range of the luminescence of $BaFBr_{1-x}I_x:Eu^{2+}$, $Na^+$ phosphor was $365{\sim}420\;nm$, and its maximum luminescence intensity appeared at 390 nm. When composition ratio x was not equal to 0, the wavelength ranges and peak of the spectra were shifted to the longer wavelength with the growth of composition ratio x. A good linearity was shown between the PSL intensity and X-ray irradiation dose. The phosphor sample with x=0.3 exhibited better fading characteristics than that of other $BaFBr_{1-x}I_x:Eu^{2+}$ phosphor samples, and the fading characteristics of the PSL intensity at room temperature were shown poorer with increasing $I^-$ ion concentration. The lattice constant of the phosphor becomes larger with increasing the $I^-$ ion concentration.

• Journal of Bio-Environment Control
• /
• v.31 no.3
• /
• pp.180-187
• /
• 2022

In order to select suitable light in a plant factory, electric energy use efficiency and light use efficiency should be considered simultaneously to consider operating costs as well as quantitative and functional aspects. The growth characteristics, electric energy use efficiency, light use efficiency by light intensity, LED ratio, and photoperiod conditions were compared together. Light intensity is 60, 130, 230, and 320 µmol·m^-2·s^-1 treatments, and light quality is the mixing ratio of red light and blue light 8:2, 6:4, 4:6, and 2:8 treatments. Photoperiod is 9, 12, 15, and 18 hours treatments based on the daytime. In the light intensity experiment, the growth rate increased as the light intensity increased, but there was no significant difference in the light use efficiency. When comparing the leaf fresh weight per power consumption, only the 320 µmol·m^-2·s^-1 treatment group showed significantly low efficiency, and there was no significant difference in the other treatments, so 230 µmol·m^-2·s^-1, which produced the most, was the most efficient. In the light quality experiment, the ratio of red light and blue light was measured to be high at the same time as the growth rate and light use efficiency in RB 8:2, and there was no significant difference in color difference and flavonoids content, so a Red:Blue ratio of 8:2 was the most suitable condition. In the photoperiod experiment, the longer the photoperiod, the higher the growth rate. However, there was no significant difference in the growth rate over 12 hours of daytime, so 12 hours considering the light consumption efficiency was a suitable condition. Based on the above results, LED light environmental conditions for perilla growth in plant factories were light intensity, light quality, and day length of 230 µmol·m^-2·s^-1 or more, 8:2, and 12 hours or more, respectively.

• Korean Journal of Agricultural Science
• /
• v.4 no.2
• /
• pp.317-343
• /
• 1977

This study was carried out to obtain the informations about evaporation from pot, soil temperature and soil atmosphere composition in pot, and the effect on the growth of nine ornamental species using seven different containers. The investigated containers were clay pot(CP), clay pot painted in green(CP-P), varnished clay pot(CP-V), polyethylene film inserting in clay pot(CP-PI), clay pot mulched with black polyethylene film(CP-PM), porcelain pot(POP), and plastic pot(PLP). Nine ornamental species were balsam(Impatiens balsamina), chrysanthemum(Chrysanthemum morifolium), cosmos(Cosmos bipinatus), English ivy(Hedera helix), geranium(Pelargonium zonale), kochia(Kochia scoparia var. trichophila), marigold(Tagetes patula), ornamental kale(Brassica oleraceae var. acephala), and salvia (Salvia splendens). The results obtained are summarized as follows: 1. Dry weight of all tested species grown in PLP, POP, CP-P, CP-V and CP-PI was heavier than that of CP. 2. Plant height in nine tested species grown in PLP, POP, CP-P, CP-V, and CP-PI was taller than that of CP. 3. Geranium grown in PLP, POP, CP-P, and CP-V gave more number of leaf than that of CP. 4. The number of flower in balsam grown in PLP, POP, CP-P, CP-V and CP-PI was more than that of CP. The result from marigold was very similar to this tendency. Spike length and floret number in salvia gave the same tendency, but its spike number was not different among containers used. 5. The average diurnal evaporation from PLP and POP was about 43% of that of CP. About two third of total evaporation from CP was through pot wall. 6. The evaporation rate from the slowest to the highest was PLP, POP, CP-P, CP-V, CP-PI, CP-PM and CP. Containers inhibiting evaporation through pot wall hold more soil moisture than CP from one day after water supply. 7. The more evaporative water-loss from containers gave the lower soil temperature. The variation of soil temperature among containers was higher during the day than the night. 8. The $O_2$ concentration of soil atmosphere in CP was higher than that of nonporous containers, and the difference between them was 0.40-1.12%. The range of the $O_2$ concentration 17.95~19.62%. The $CO_2$ concentration of soil atmosphere in CP was lower than that of nonporous containers, and its range was 0.59-1.76%. This deviation in soil atmosphere composition did not influenced on the growth of plants. 9. There was a possitive correlation between the amount of soil water and the plant growth. 10. Plant grown on CP gave more total nitrogen content in top growth than that on PLP. C/N ratio was somewhat low in plant on CP. From the above results, $O_2$ and $CO_2$ concentration in soil atmosphere did not gave enough deviation to the extent which affect the plant growth. The effect of soil moisture on the plant growth using different containers was the far-most significant factor from this investigation. Therefore, it was obious that the utilization of the nonporous container might save the cost for water supply and reduce the production cost of the pot-grown ornamental plant in Korea eventually.

• Korean Journal of Organic Agriculture
• /
• v.22 no.4
• /
• pp.731-742
• /
• 2014

In the current study, we investigated effects of a combination of earthworm casting, environment-friendly by-product fertilizer, and cultivation soil of Gymnocalycium mihanovichii in a heavy fertilizing culture on diameter, height, numbers of tubercles, and chemical properties of soil thereby elucidating optimal mixture ratio for securing production as well as providing nutrients throughout cultivation period. The Gymnocalycium mihanovichii var 'Ihong', one of grafted cactus for export (Rootstock: 9 cm, Scion: $1.5{\times}1.3cm$ grafted cactus) was cultured in plastic houses of Agricultural Technology Center located in Naegok-dong, Seocho-gu, Seoul from June, 2013 through December, 2013. For the control group, a mixture of sand and fertilizer (50:50) was used as this ratio is widely utilized in farmhouses. In contrast, a variety mixtures of sand and earthworm casting that was produced with food wastes was compared; the mixture ratios were 80:20, 60:40, 40:60, 20:80, and 0:100 and pH for these mixtures were found to be similar each other (ranging between 7.1 and 7.4) which is in an appropriate range (pH 6.5-7.5) for cultivation of G. mihanovichii. The organic content was increasing along with increasing contents of earthworm casting ratio while it was lower than the treatment practice group (32-43 mg/kg vs. 55 mg/kg). The content of exchangeable cation was also increasing as the ratio of earthworm casting was elevated; although levels of $K^+$, $Na^+$, and $Mg^{2+}$ were lower than the treatment practice group, the level of $Ca^{2+}$ was higher ($9.1cmol^+/kg$ and $11.5-33.7cmol^+/kg$ in the treatment practice group and the earthworm casting group, respectively). Three months after grafting, diameters of G. mihanovichii were compared with the control group; consequently, there was a significant difference noted in between the earthworm casting group and the control group (31.39 mm vs. 32.46-37.59 mm). After 5 months, growth characteristics of G. mihanovichii were evaluated. Similarly, the diameter of G. mihanovichii was significantly increasing in the group with higher ratio of earthworm casting treatment (32.63 mm vs. 32.49-37.59 mm). The height of tubercles was 2.63 mm in the control group while it was significantly elevating along with the ratio of earthworm casting mixture. The more numbers of tubercles, the more incomes for farm-houses; as results, higher mixture ration of earthworm casting resulted more numbers of tubercles compared to the control group (2.7 vs. 3.2-8.3 ea). In particular, in the earthworm casting groups with 80% and 100% ratios, the numbers of tubercles were 6.2 and 8.3 ea, respectively, which is 2.5 times more than those of the control group. These results indicate that earthworm casting treatment may be utilized in G. mihanovichii farming houses for short term production of tubercles. In the group with 40% and 60% of earthworm casting mixture, the numbers of tubercles were found to be 4.5 and 4.8 ea, respectively which is higher than the control group as well; in these groups, there were no issues with soil drainage as well as moss formation. Given the analysis results of growth characteristics of G. mihanovichii, it was concluded that 40% and 60% of earthworm casting mixture might be the optimal ratios.

• Journal of Bio-Environment Control
• /
• v.30 no.1
• /
• pp.77-84
• /
• 2021

This study attempted to find a way to maintain the quality of mixing baby wild leaf vegetables with existing baby leaf vegetables in various ratios. The crops for mixing baby leaf vegetables were Peucedanum japoincum Thunberg and Ligularia stenocephala, as wild vegetables, and red romaine, which is widely used in young leafy vegetables. The mixing ratio of red romaine and wild vegetables was red romaine 0: mantilla oil 5: L. stenocephala ratio 5 (R0: P5: L5), red romaine 3.3: P. japoincum 3.3: L. stenocephala ratio 3.3 (R3.3: P3.3: L3.3), red romaine 5: P. japoincum 2.5: L. stenocephala 2.5 (R5: P2.5: L2.5), red romaine 8: P. japoincum 1: L. stenocephala 1 (R8: P1: L1), red romaine 10: P. japoincum 0: L. stenocephala 0 (R10: P0: L0). All treatments were packaged in OTR (oxygen transmittance) 10,000 cc m-2·day-1·atm-1 film and stored for 27 days at 2℃/85% RH conditions. Fresh weight, carbon dioxide, oxygen, and ethylene concentrations of the baby leaf packages were examined approximately every 3 days, and visual quality, chlorophyll content, and chromaticity were examined on the 27th day of storage. The oxygen and carbon dioxide concentration in the packages were affected by the respiration rate of the crop. As the mixing ratio of lettuce, which had a low respiration rate, increased, the oxygen concentration in the packages was higher and the carbon dioxide concentration was lower. Oxygen concentration decreased significantly after 15 days, but was remained above 16%, and on the contrary, carbon dioxide concentration was kept at 1-4% until the 15th, and then gradually increased to 2-5% on the 27th day. The concentration of ethylene was maintained at 3-6 µL·L-1 until the end of storage (27th day). Visual quality score measured at the end of storage was slightly less than 3.0, which is the limit of marketability of all treatments. Although there was no significant difference, the chlorophyll content (SPAD) of red romaine and P. japoincum were most similar with an initial value in R8:P1:1 treatment, and L. stenocephala was higher value in R8:P1:L1 and R5:P2.5:L2.5 treatments at the end of storage. The leaf color (L∗, a∗, b∗, chroma) of the three crops at end of storage compared with the heat map showed the least change in the R5:P2.5:L2.5 and R8:P1:L1 treatments at the end of storage. Among them, R8:P1:L1 treatment maintained the highest chlorophyll content, the second lowest ethylene concentration, and adequate carbon dioxide concentration of 2-3%. Therefore, it is judged that the mixed ratio of red romaine 8: P. japoincum 1: L. stenocephala 1 (R8: P1: L1) is most suitable for the mixed package of baby leaf vegetables of these three crops.

• Applied Chemistry for Engineering
• /
• v.17 no.3
• /
• pp.243-249
• /
• 2006

Porous polymer gel electrolytes (PGEs) based on poly(vinylidenefluoride-co-hexafluoropropylene) (P(VdF-co-HFP)) as a polymer matrix and polyvinylpyrolidone (PVP) as a pore-forming agent were prepared and electrochemical properties were investigated for an electric double layer capacitor (EDLC) in order to increase a permeability of an electrolyte into the PGE. Propylene carbonate (PC) and ethylene carbonate (EC) as plasticizers, and tetraethylammonium tetrafluoroborate ($TEABF_4$) as a supporting salt for the PGE were used. EDLC unit cells were assembled with the PGE and electrode comprising BP-20 and MSP-20 as activated carbon powders, Super P as a conducting agent, and P(VdF-co-HFP)/PVP as a mixed binder. Ion conductivity of PGEs increased with an increased PVP content and was the best at 7 wt% PVP, whereas electrochemical characteristics such as AC-ESR of unit cell were better in 3 wt%. And electrochemical characteristics of the unit cell with PGE were the best at a 33 : 33 weight ratio of PC to EC. Specific capacitance of a mixed plasticizer system of PE and EC was higher than that of pure PC. Ion conductivity of PGEs with a film thickness of $20{\mu}m$ was higher, but electrochemical characteristics of unit cells were higher for a $50{\mu}m$ membrane thickness. Also, the unit cell has shown the highest capacitance of 31.41 F/g and more stable electrochemical performance when PGE and electrode were hot pressed. Consequently, the optimum composition ratio of PGE for EDLCs was 23 : 66 : 11 wt% such as P(VdF-co-HFP) : PVP = 20 : 3 wt% and PC : EC = 44 : 22 wt%. In this case, $3.17{\times}10^{-3}S/cm$ of ion conductivity was achieved at the $50{\mu}m$ thickness of PGE for EDLCs. And the electrochemical characteristics of unit cells were $2.69{\Omega}$ of DC-ESR, 28 F/g of specific capacitance, and 100% of coulombic efficiency.

• Journal of the Korea Concrete Institute
• /
• v.21 no.3
• /
• pp.245-253
• /
• 2009

The importance of chloride ions in the corrosion of steel in concrete has led to the concept for chloride threshold level (CTL). The CTL can be defined as the content of chlorides at the steel depth that is necessary to sustain local passive film breakdown and hence initiate the corrosion process. Despite the importance of the CTL, due to the uncertainty determining the actual limits in various environments for chloride-induced corrosion, conservative values such as 0.4% by weight of cement or 1.2 kg in 1 $m^3$ concrete have been used in predicting the corrosion-free service life of reinforced concrete structures. The paper studies the CTL for blended cement concrete by comparing the resistance of cementitious binder to the onset of chloride-induced corrosion of steel. Mortar specimens were cast with centrally located steel rebar of 10 mm in diameter using cementitious mortars with ordinary Portland cement (OPC) and mixed mortars replaced with 30% pulverized fuel ash (PFA), 60% ground granulated blast furnace slag (GGBS) and 10% silica fume (SF), respectively, at 0.4 of a free W/B ratio. Chlorides were admixed in mixing water ranging 0.0, 0.2, 0.4, 0.6, 0.8, 1.0, 1.5, 2.0, 2.5 and 3.0% by weight of binder(Based on $C1^-$). Specimens were curd 28 days at the room temperature, wrapped in polyethylene film to avoid leaching out of chloride and hydroxyl ions. Then the corrosion rate was measured using the polarization resistance method and the order of CTL for binder was determined. Thus, CTL of OPC, 60%GGBS, 30%PFA and 10%SF were determined by 1.6%, 0.45%, 0.8% and 2.15%, respectively.

• Journal of Korean Ophthalmic Optics Society
• /
• v.9 no.2
• /
• pp.333-343
• /
• 2004

Impression cytology refers to application of cellulose acetate filter material to the ocular surface to remove the superficial layers of the conjunctival epithelium. The technique is non-invasive, is easy to perform, causes minimal discomfort to the patient, and can be used to follow changes in the conjunctival ocular surface over time. With this method, the morphology of the conjunctival ocular surface can be studied and the degree of squmaous metaplasia assessed. This study was performed to evaluate the conjunctival surface by impression cytology in dry eye patients. A total of 70 students with no contact lens wearing history were recruited. Subjects were required to fill in a McMonnies dry eye symptom questionnaire. The non-invasive tear thinning time(TIT) test of each subject was measured, followed by Schirmer tear test(STI), tear film break-up time(TBUT) tests and Rose-bengal staining were performed as a baseline. Conjunctival epithelial cells from the inferior bulbar conjunctiva were harvested by the impression cytology technique. The specimens collected were labelled and stained with PAS(Periodic Acid Schift)-haematoxylin. The goblet cells and conjunctival epithelial cells were observed under a light microscope of 400x magnification. The specimens were classified according to the Nelson Grading scale which was based on the degree of squamous metaplasia such as changes of goblet cells density, size/form, N:C(nucleus : cytoplasm) ratio. Dry eye patients were observed morphological changes of the epithelial cells, different nuclear alterations, decrease of the goblet cells density. The degree of cytological changes was related to severity of dry eye conditions. When the epithelial cell morphology was graded according to the system described by Nelson, specimens from the control group revealed 91.43% of the eyes to be grade 0 and 8.57% to be grade 1, whereas of the dry eye patients, 20% were grade 0, 42.86% grade 1, 34.29% grade 2 and 2,86% grade 3. Impression cytology represents a non- or minimally invasive biopsy of the ocular surface epithelium with no side effects or contraindications. It has demonstrated to be a useful diagnostic aid for a wide variety of processes involving the ocular surface. This technique is a safe, simple method and may help increase understanding of various ocular surface alterations in dry eye patients.

• Journal of the Korean Society of Radiology
• /
• v.3 no.2
• /
• pp.27-31
• /
• 2009

Now a days, the Medical X-ray equipments has become digitalized from analog type such as film, cassette to CR, DR. And many scientists are still researching and developing the Medical X-ray equipment. In this study, we used the Bismuth tri-iodide to conversion material for digital X-ray equipments and we couldn't get the satisfying result than previous study, but it opened new possibility to cover the disadvantage of a-Se is high voltage aplly and difficultness of make. In this paper, we use $BiI_3$ powder(99.99%) as x-ray conversion material and make films that have thickness of 200um and the film size is $3cm{\times}3cm$. Also, we deposited an ITO(Indium Tin Oxide) electrode as top electrode and bottom electrode using a Magnetron Sputtering System. To evaluate a characteristics of the produced films, an electrical and structural properties are performed. Through a SEM analysis, we confirmed a surface and component part. And to analyze the electrical properties, darkcurrent, sensitivity and SNR(Signal to Noise Ratio) are measured. Darkcurrent is $1.6nA/cm^2$ and sensitivity is $0.629nC/cm^2$ and this study shows that the electrical properties of x-ray conversion material that made by screen printing method are similar to PVD method or better than that. This results suggest that $BiI_3$ is suitable for a replacement of a-Se because of the reduced manufacture processing and improved yield.

• Korean Chemical Engineering Research
• /
• v.49 no.1
• /
• pp.75-82
• /
• 2011

Five different composition UV-cured poly(urethane acrylate-co-acrylic acid) (PU-co-AA) films have been prepared by reacting isophorone diisocyanate(IPDI), polycaprolactone triol(PCLT), 2-hydroxyethyl acrylate(HEA), and different weight ratio trimethylolpropane triacrylate(TMPTA) and acrylic acid(AA) as diluents, and characterized using a Fourier transform infrared spectroscopy(FT-IR). The adhesion properties onto the stainless steel, morphology, mechanical hardness, and electrical property of UV-cured PU-co-AA films were investigated as a function of acrylic acid(AA) content. All the PU-co-AA films are structure-less and the molecular ordering and packing density decreased with increasing content of AA due to the flexible structure and -COOH side chains in AA. The crosscut test showed that PU-co-AA films without AA and with low content of AA showed 0% adhesion(0B) and the adhesion of PU-co-AA films in the range of 40-50% AA increased dramatically as the content of AA increases. The pull-off measurements showed that the adhesion force of PU-co-AA films to stainless steel substrate varied from 6 to 31 kgf /$cm^2$ and increased linearly with increasing AA content. The mechanical hardness also decreased as the content of AA increases. This may come from relatively linear and flexible structure in AA and low crystallinity in PU-co-AA films with higher content of AA. The higher AA-containing PU-co-AA films showed higher dielectric constant due to the increase of polarization by introducing AA monomer. In conclusion, the physical properties of UV-cured PU-co-AA films are strongly dependent upon the content of AA and the incorporation of AA in polyurethane acrylate is very useful way to increase the adhesion strength of UV-curable polymers on the stainless steel substrate.