• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2000.04a
• /
• pp.55-55
• /
• 2000

Cylinder machine usually gives more fiber orientation than fourdrinier and has limitation in machine speed because of fiber wash-off caused by centrifugal force in case of adding machine speed. This study aimed at improvement of paper formation and higher productivity by setting up an apron in vat inlet and by adjustment of mould water head. As results, there were improvement of formation and increase of machine speed, which ultimately improve productivity. Setting up an apron successfully decreased fiber wash-off. Fiber orientation and two-sideness of ash distribution became less severe. These results could lead to better dimension stabilities in the CD through mitigation of fiber orientation and also could result in less curl from two-sideness of paper. The proper adjustment of water head inside the cylinder mould proved to be important factor not only in paper formation but also in decreasing paper two-sideness.

• 한국기계연구소 소보
• /
• s.15
• /
• pp.57-66
• /
• 1985

Fibers with a high degree of axial preferred orientation can be obtained from mesophase pitch. Prior to cabonization, the pitch fibers must be rendered in fusible so that their orientation is preserved. The stabilization of the pitch fibers was heated at temperature between $250^{circ}C$ and $300^{circ}C$ and a treatment time 5 to 80minutes. Oxidized fibers heated $1800^{circ}C$without stretching. Pitch based carbon fiber have a young's modulus as high as 304GN/$m^2$. The structure of the pitch cased carbon fiber is determining factor for the mechanical properties of the produced fibers. The structure depending on the pitch precursor as well as on the oxidation time.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.10a
• /
• pp.108-113
• /
• 2004

The compressive axial collapse tests were performed to investigate energy absorption characteristics of Al/CFRP compound tubes which are aluminum tubes wrapped with CFRP (Carbon Fiber Reinforced Plastics) outside the aluminum circular and square tubes. Based on collapse characteristics of aluminum tubes and CFRP tubes respectively, the axial collapse tests were performed for Al/CFRP compound tubes which have different fiber orientation angles. Test results showed that Al/CFRP compound tubes supplemented the unstable brittle failure of CFRP tubes due to ductile nature of inner aluminum tubes. In the light-weight aspect, specific energy absorption were the highest for Al/CFRP, CFRP in the middle, and aluminum the lowest. Also, specific energy absorption of circular tubes was higher than square tubes'. It turned out that fiber orientation angle of Al/CFRP compound tubes influence specific energy absorption together with the collapse modes of the tubes.

• Macromolecular Research
• /
• v.10 no.5
• /
• pp.282-285
• /
• 2002

In this paper, we report a modified technique for the production of oriented continuous nanofibers instead of non-woven mats using a rapidly rotating collection device. We are interested in retaining physical properties such as electrical conductivity of fiber bundles in their axial direction. The experiments were performed using polyethylene oxide (PEO) and its blend with polyaniline (PANI). According to the results, a typical fiber with a uniform diameter of about 100 nanometer was produced. The fibers from the PEO/ CHCl$_3$ solution show high crystallinity and good orientation whereas the fibers from the blend solution of PEO/PANI/m-cresol and CHCl$_3$ show no preferred orientation. However, the fibers of the blend exhibit high electrical conductivity of 33 S/cm for a fiber bundle at a PANI level of 50 %.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.6
• /
• pp.49-56
• /
• 2015

To investigate fiber orientation of Korean traditional paper, Hanji, the fiber arrangements on the surface and cross section of Hanji were observed by scanning electron microscope (SEM). The surface observation showed that the fibers of traditional paper were arranged in vertical and horizontal directions, and those of ssangbal sheet forming were arranged more in vertical direction. The fibers of machine made Hanji and copying paper were usually arranged in vertical direction. As for the observation of cross section of traditional paper, fibers arranged in horizontal direction tended to be increased with the increase of thicknesses. The thick traditional paper have cracks in the middle part of structural section of paper. They were larger in cross section in horizontal direction than in vertical direction. The horizontal arrangement of traditional paper seemed to be about 8% to 14% higher to the vertical arrangement, which is very lower to other papers.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1530-1532
• /
• 2000

The properties of FRP usually depends on the fabricating method. The fiber orientation of FRP is also depends on the fabricating method. The fiber orientation in FRP has a great effect on the strength of FRP because the strength of FRP mainly depends on the strength of fiber. In this study. compressive and bending strength of FRP rods were investigated. Inner part of FRP was made unidirectionally by pultrusion method and outer part of FRP was made by wrapping method. The size effect was also investigated with pultruded FRP rods.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.143-146
• /
• 2004

Fiber reinforced plastic material should be inspected in fabrication process in order to enhance quality by prevent defects such as delamination and void. Generally, ultrasonic technique is widely used to evaluate FRP. In conventional ultrasonic techniques, transducer should be contacted on FRP. However, conventional contacting method could not be applied in fabrication process and novel non-contact evaluating technique was required. Laser-based ultrasonic technique was tried to evaluate FRP plate. Laser-based ultrasonic waves propagated on CFRP were received with various transducers such as accelerometer and AE sensor in order to evaluated the properties of waves due to the variation of frequency. Velocities of laser-based ultrasonic waves were evaluated for various fiber orientation.

• Wind and Structures
• /
• v.29 no.5
• /
• pp.361-369
• /
• 2019

The modal frequency responses of adhesive bonded T-joint structure have been analyzed numerically and verified with own experimental data. For this purpose, the damped free frequencies of the bonded joint have been computed using a three-dimensional finite element model via ANSYS parametric design language (APDL) code. The practical relevance of the joint structure analysis has been established by comparing the simulation data with the in-house experimental values. Additionally, the influences of various geometrical and material parameters on the damped free frequency responses of the joint structure have been investigated and final inferences discussed in details. It is observed that the natural frequency values increase for the higher aspect ratios of the joint structure. Also, the joint made up of Glass fiber/epoxy with quasi-isotropic fiber orientation indicates more resistance towards free vibration.

• Kyungpook Mathematical Journal
• /
• v.62 no.2
• /
• pp.363-388
• /
• 2022

In two previous papers the author presented a general construction of finite, fiber- and orientation-preserving group actions on orientable Seifert manifolds. In this paper we restrict our attention to elliptic 3-manifolds. For illustration of our methods a constructive proof is given that orientation-reversing and fiber-preserving diffeomorphisms of Seifert manifolds do not exist for nonzero Euler class, in particular elliptic 3-manifolds. Each type of elliptic 3-manifold is then considered and the possible group actions that fit the given construction. This is shown to be all but a few cases that have been considered elsewhere. Finally, a presentation for the quotient space under such an action is constructed and a specific example is generated.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.5
• /
• pp.806-811
• /
• 2013

In this study, to prevent the nonhomogeneity of fiber orientation during the molding of GFRP composites, GFRP prepreg was fabricated using roving fiber and polypropylene resin. Analyses on the degree of impregnation, tensile strength, and microstructure were conducted on the fabricated prepregs. A lower pulling speed, higher resin temperature, and longer die length showed a greater degree of impregnation of the prepreg. The scanning electron microscope (SEM) micrograph showed, a homogeneous fiber orientation. As a result, fundamental techniques for improved productivity were suggested for the manufacturing field.