• Current Optics and Photonics
• /
• v.5 no.2
• /
• pp.141-146
• /
• 2021

We have evaluated the suppression effect of atmospheric-turbulence-induced optical scintillation in terrestrial free-space optical (FSO) communication systems using a gain-saturated erbium-doped fiber amplifier (EDFA). The variation of EDFA output signal power has been measured with different amounts of gain saturation and modulation indices of the optical input signal. From the measured results, we have found that the peak-to-peak power variation was decreased drastically below 2 kHz of modulation frequency, in both 3-dB and 6-dB gain compression cases. Then, the power spectral density (PSD) of optical scintillation has been calculated with Butterworth-type transfer function. In the calculation, different levels of atmospheric-turbulence-induced optical scintillation have been taken into account with different values of the Butterworth cut-off frequency. Finally, the suppression effect of optical scintillation has been estimated with the measured frequency response of the EDFA and the calculated PSD of the optical scintillation. From our estimated results, the atmospheric-turbulence-induced optical scintillation could be suppressed efficiently, as long as the EDFA were operated in a deeply gain-saturated region.

• Korean Journal of Optics and Photonics
• /
• v.32 no.4
• /
• pp.187-194
• /
• 2021

This paper presents a study of laser output characteristics. We fabricated a MOPA (master oscillator power amplifier)-type high-power, narrowbandwidth fiber laser with a bidirectional pumping configuration in its main amplifier. As signal beams, light sources with bandwidths of 3 GHz and 10 GHz-phase-modulated through a PRBS (pseudo-random binary sequence)-were used interchangeably. Furthermore, the characteristics of the SBS (stimulated Brillouin scattering) were analyzed using a signal beam with 3 GHz bandwidth, by adjusting the forward to backward pumppower ratio. Moreover, the characteristics of the transverse mode instability were analyzed by adjusting the forward to backward pump-power ratio, using a signal beam with 10-GHz bandwidth. Finally, the output power from 10 GHz bandwidth was amplified to more than 1 kW using a forward to backward pump-power ratio of 1.6. The beam quality M² was measured to be approximately 1.36, and the optical-to-optical efficiency was 80% at maximum output power.

• Proceedings of the Optical Society of Korea Conference
• /
• 2000.02a
• /
• pp.72-73
• /
• 2000

Optical fiber gratings have been intensively studied for applications in optical fiber communications and sensor systems due to their all-fiber configuration, low insertion loss, low cost, and high flexibility. Especially, cladding mode coupling fiber devices such as long period gratings (LPG) and acousto-optic tunable filters (AOTF) have been developed as a gain equalization filter in erbium doped fiber amplifier (EDFA) for wavelength division multiplexing (WDM) systems$^{(1-2)}$ . (omitted)

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.383-386
• /
• 2008

We developed a fiber-optic Bragg grating sensor system using a SOA fiber laser for over heat detection in power systems. To compensate the nonlinear wavelength tuning of the fiber laser, we used fixed passband wavelengths from Fabry-Perot ITU filter as reference wavelengths. Gaussian line-fitting algorithm was also used to reduce the FBG peak detection error. Compared with a highest-peak-detection and a polynomial-fitting method, the proposed Gaussian fitting algorithm could drastically reduce the measurement errors. Also the SOA fiber laser made it possible to enhance the signal-to-noise-ratio even with several kilometers of lead fiber.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.7
• /
• pp.15-22
• /
• 1997

A 10Gbit/s limiting amplifier IC for optical transmission system was implemented with AlGaAs HBT (heterojunction bipolar transistor) technology. HBTs with 2x10.mu. $m^{2}$ and 6x20.mu. $m^{2}$ emitter size were used. The HBT structures are based on metal-organic chemical vapor deposition (MOCVD) epitxy and employ a mesa structure with self-aligned emitter/base and sidewall dielectric passivation. IC was designed to support differnetial input and output. Small signal performance of the packaged IC showed 26dB gain and $f_{3dB}$ of 8GHz. A single ouput has 800m $V_{p-p}$ swing with more than 26dB dynamic range. The performance of the limiting amplifier was verified through single mode fiber320km transmission link test.est.

• Korean Journal of Optics and Photonics
• /
• v.27 no.3
• /
• pp.95-100
• /
• 2016

High-power quasi-continuous-wave (qcw) operation in Yb-doped double-clad fiber lasers with near-diffraction-limited quality of the output beam is reported. Based on numerical simulation, we built a simple, all-fiberized Yb fiber laser, and a fiber-based master-oscillator power amplifier (MOPA). Both laser systems have successfully produced qcw output with average power greater than 150 W at 1080 nm and 10 ms pulse duration at 10 Hz repetition rate, corresponding to a peak power greater than 1.5 kW for 205 W of pump power at 976 nm. Laser performance, including beam quality and slope efficiency, was characterized in both configurations. Prospects for power scaling and applications are discussed.

• Korean Journal of Optics and Photonics
• /
• v.30 no.4
• /
• pp.167-173
• /
• 2019

In this paper, we studied characteristics of stimulated Brillouin scattering (SBS) suppression in high-power fiber lasers by using apparatuses applying a temperature gradient (i.e. a step, a sine shape, and random temperature distribution) along the fiber. From the ytterbium-doped polarization-maintaining fiber master oscillator power amplifier built in house, we measured the back-reflection spectrum and power for each temperature gradient, showing that the step shape temperature distribution was the most effective way to suppress SBS. In addition, we investigated the interaction of pseudo-random binary sequence phase modulation conditions and temperature gradients for SBS suppression.

• Korean Journal of Optics and Photonics
• /
• v.31 no.1
• /
• pp.7-12
• /
• 2020

In this paper, we experimentally investigate the fiber fuse in single-mode 2-kW-class high-power fiber amplifiers, depending on the cooling method at the splicing point. We measured the temperature of the splicing point between the pump-signal combiner and gain fiber as a function of laser output power. The temperature of the splicing point increased from 20 to 32℃ with a slope of 0.01℃/W, up to 1.2 kW of laser output power. At higher powers the temperature of the splicing point increased dramatically, with a slope of 0.08℃/W. After that, the fiber amplifier was destroyed during operation at 1.96 kW of output power by fiber fuse. The bullet shape, a common feature of fiber fuse, was observed in the damaged passive fiber core of the pump-signal combiner. Later, we adopted an improved water-cooled cold plate to increase the cooling efficiency at the splicing point, and investigated the laser output power. The temperature at the splicing point was 35.8℃ with a temperature-rise slope of 0.007℃/W at the maximum output power of 2.05 kW. The beam quality M² was measured to be less than 1.3, and the output beam's profile was a stable Gaussian shape. Finally, neither fiber fuse nor mode instability was observed in the fiber amplifier at the maximum output power of 2.05 kW.

• Korean Journal of Optics and Photonics
• /
• v.6 no.1
• /
• pp.70-75
• /
• 1995

Erbium 첨가 광섬유를 광원겸 광증폭기로 사용하는 방식으로 개회로 형태의 광섬유 gyroscope를 구성하였다. Erbium 첨가 광섬유를 거쳐 5mW 이상의 gyro 출력광 power와 7nm의 파장선폭을 얻었다. Loop 광섬유로부터 광증폭기형 광원으로의 feedback으로 인하여 회전속도에 따라 scale factor가 변화함을 관찰할 수 있었다. 그러나 변조된 gyro 출력신호광의 평균 power가 회전속도에 무관하도록 위상차의 변조진폭을 $\PHI_m=2.405 rad$으로 한 경우에 회전속도와 무관한 일정한 scale factor를 얻을 수 있었다.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.02a
• /
• pp.330-331
• /
• 2003

분포형 광섬유 센서시스템은 일정한 길이의 연속적인 광섬유 및 광케이블을 매질로 하여 길이 방향에서 생기는 투과율 또는 산란 특성의 변화를 통해 물리량의 변화와 그 위치를 감지하는 시스템을 말한다. 그 중에서 광섬유 내부의 브릴루앙 산란효과를 이용하여 광케이블 주위에 진동, 압력등에 매우 민감한 분포형 광섬유센서를 구성하고 외부로부터의 침입 유무와 위치를 파악함과 동시에 주요시설물의 감시 및 진단이 가능하도록 한다. (중략)