• International Journal of Aeronautical and Space Sciences
• /
• 제18권2호
• /
• pp.236-244
• /
• 2017

In this study, the high-velocity impact penetration behavior of $[45/0/-45/90]_{ns}$ carbon/epoxy composite laminates was studied. The considered configuration includes a spherical steel ball impacting clamped circular laminates with various thicknesses and diameters. First, the impact experiment was performed to measure residual velocity and extent of damage. Next, the impact experiment was numerically simulated through finite element analysis using LS-dyna. Three-dimensional solid elements were used to model each ply of the laminates discretely, and progressive material failure was modeled using MAT162. The result indicated that the finite element simulation yielded residual velocities and damage modes well-matched with those obtained from the experiment. It was found that fiber damage was localized near the impactor penetration path, while matrix and delamination damage were much more spread out with the damage mode showing a dependency on the orientation angles and ply locations. The ballistic-limit velocities obtained by fitting the residual velocities increased almost linearly versus the laminate diameter, but the amount of increase was small, showing that the impact energy was absorbed mostly by the localized impact damage and that the influence of the laminate size was not significant at high-velocity impact.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2005년도 제31회 KOSCO SYMPOSIUM 논문집
• /
• pp.120-131
• /
• 2005

The evaporation characteristics of single and multicomponent droplets hanging at the tip of a quartz fiber are studied experimentally at the different environmental conditions under normal gravity. Heptane and Hexadecane are selected as two fuels with different evaporation rates and boiling temperatures. At the first step, the evaporation of single component droplet of both fuels has been examined separately. At the next step the evaporation of several blends of these two fuels, as a binary component droplet, has been studied. The temperature and pressure range is selected between 400 and 700 $^{\circ}C$, and 0.1 and 2.5 MPa, respectively. High temperature environment has been provided by a falling electrical furnace. The initial diameter of droplet was in range of 1.1 and 1.3 mm. The evaporation process was recorded by a high speed CCD camera. The results of binary droplet evaporation show the three staged evaporation. In the the first stage the more volatile component evaporates. The droplet temperature rises after an almost non evaporating period and in the third stage a quasi linear evaporation takes place. The evaporation of the binary droplet at low pressure is accompanied with bubble formation and droplet fragmentation and leads to incomplete microexplosion. The component concentration affects the evaporation behavior of the first two stages. The bubble formation and droplet distortion does not appear at high environment pressure. Nomenclature

• 한국방재학회 논문집
• /
• 제3권1호
• /
• pp.123-131
• /
• 2003

파형강관을 삽입하여 보강된 중공원형단면의 역학적 거동을 연구하기 위하여 직경 50cm, 길이 340cm의 시험체를 제작하였고, 3점 휨시험을 수행하였다. 하중재하는 파괴 또는 최대한변형이 발생할 때까지 느리게 증가시켰다. 시험하는 동안에 시험체 중앙의 휨방향 변위와 인장측과 압축측의 종방향 변위를 측정하였다. 측정데이타를 분석한 결과를 파형강관이 삽입되지 않은 등가단면에 대한 해석결과와 비교하였다. 비교결과, 중공 철근콘크리트 부재의 휨강성과 연성이 파형강관을 내부에 삽입함으로써 크게 향상시킬 수 있는 것으로 나타났다.

• Tribology and Lubricants
• /
• 제26권6호
• /
• pp.311-316
• /
• 2010

Surface texturing of micro dimple or pore-shaped pattern was prepared using a fiber laser system. Surface texturing was designed to have a square pattern with a particular pitch distance for each corresponding density of 5, 10, 20, and 30%. Thermal damages such as bulges and burrs formed during laser irradiation were observed around the dimples. Thermal damages were later removed by lapping using alumina particles of $0.3{\mu}m$ in diameter. Oscillating friction tests were performed against heat-treated high speed steels under lubricated condition. The lubricant used was SAE 5W-30 automotive engine oil. Normal contact pressure and oscillating frequency was 0.28 MPa and 20 Hz, respectively. The tests were continued for 20 minutes, and friction plots were recorded for examination. Results revealed that the coefficient of friction was lowered regardless of texturing density. Moreover, the lowest coefficient of friction was obtained for 10% density texturing. It is attributed to increased lubricity due to the introduction of surface texturing. In addition, it is concluded that the optimum texturing density and pattern must be found for the best lubricity and low friction.

• 한국광학회지
• /
• 제15권2호
• /
• pp.158-170
• /
• 2004

유선 통신의 포화지역이나 도심에서 벗어난 인구밀도가 낮은 지역 둥에서 고속 광통신을 위해 최근 무선 광통신이 새롭게 기대되고 있다. 본 논문에서는 이러한 무선 광통신을 위한 송신 광학계를 설계하였는데, 광원으로는 수평(7$^{\circ}$)및 수직(18$^{\circ}$) 발산각이 다른 비대칭 타원형 빔을 발산하는 레이저 다이오드(중심 파장 830 nm)를 사용하였다. 제안되는 송신 광학계는 장거리 전송(500 m∼1500 m)이 가능하고, 장거리 전송 후 수신단에서 빔 직경(3 m) 및 에너지 분포가 대칭형이 되도록 설계되었다. 이를 위해 비결상 광학계인 송신 광학계의 평가법으로 에너지 전달 효율과 복사 조도 분포를 계산하였다.

• 한국막학회:학술대회논문집
• /
• 한국막학회 1996년도 추계 총회 및 학술발표회
• /
• pp.18-21
• /
• 1996

Virus and DNA removal in bio-drug manufacturing processes has received a great deal of attention in recent years. Removing of a virus using a membrane process is a promising method, because inactivated virus can be removed from the bio-drug and the process can be used as an additional and security inactivation after the method of general heat-inactivation of the virus in the bio-drug. The FDA and the biopharmaceutical industry have recently announced strict guidelines for impurities of virus and DNA contamination. The regulatory guidelines on residual amounts of DNA in mammalian cell culture products require DNA contamination of less than 100 pg/dose. Therefore, permeation and rejection of DNA through the porous membranes have become important in the application of DNA removal in bio-drug manufacturing using membrane technology. In this study, the permeation of DNA and chromatin through regenerated cellulose hollow fibers that have a mean pore diameter of 15 nm was investigated.

• Carbon letters
• /
• 제9권2호
• /
• pp.108-114
• /
• 2008

We have demonstrated the feasibility of using electrospinning method to fabricate long and continuous composite nanofiber sheets of polyacrylonitrile (PAN) incorporated with zinc oxide (ZnO). Such PAN/ZnO composite nanofiber sheets represent an important step toward utilizing carbon nanofibers (CNFs) as materials to achieve remarkably enhanced physico-chemical properties. In an attempt to derive these advantages, we have used a variety of techniques such as field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM) and high resolution X-ray diffraction (HR-XRD) to obtain quantitative data on the materials. The CNFs produced are in the diameter range of 100 to 350 nm after carbonization at $1000^{\circ}C$. Electrical conductivity of the random CNFs was increased by increasing the concentration of ZnO. A dramatic improvement in porosity and specific surface area of the CNFs was a clear evidence of the novelty of the method used. This study indicated that the optimal ZnO concentration of 3 wt% is enough to produce CNFs having enhanced electrical and physico-chemical properties.

• Fibers and Polymers
• /
• 제5권2호
• /
• pp.122-127
• /
• 2004

In this study, we evaluated the effect of the molecular weight of the polymer on electrospun poly(ethylene terephthalate) (PET) nonwovens, and their mechanical properties as a function of the linear velocity of drum surface. Polymer solutions and electrospun PET nonwovens were characterized by means of viscometer, tensiometer, scanning electron microscope(SEM), wide angle X-ray diffraction measurement (WAXD) and universal testing machine (UTM). By keeping the uniform solution viscosity, regardless of molecular weight differences, electrospun PET nonwovens with similar average diameter could be obtained. In addition, the mechanical properties of the electrospun PET nonwovens were strongly dependent on the linear velocity of drum surface. From the results of the WAXD scan, it was found that the polymer took on a particular molecular orientation when the linear velocity of drum surface was increased. The peaks became more definite and apparent, evolving from an amorphous pattern at 0 m/min to peaks and signifying the presence of crystallinity at 45 m/min.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 추계학술발표대회 논문집
• /
• pp.87-90
• /
• 2003

In Resin transfer molding (RTM), composite parts are produced by impregnation of a dry reinforcement with liquid matrix resin. Permeability is a key issue in this process. For thin parts, the resin flow in the thickness direction can be neglected. Therefore thin parts are considered as two-dimensional composites. However the resin flow through the thickness is important to thicker parts and we have to consider out-of-plane permeability. This work discusses a method to measure out-of-plane permeability. The flow rate and pressure drop across the porous media were measured. Also one dimensional form of Darcy's law is applied to calculate the out-of-plane permeability of various preforms. The flow is injected uniformly into layers of the preform. And a circular fiber mat with 6cm diameter was cut and flattened from cylindrical mandrel.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1911-1915
• /
• 2003

Today optical communication industry is developed; demand of optical communication part is increased. ZrO$_2$ ceramic ferrule is very significant part which determines transmission efficiency and quality of information in the optical communication part by connector of optical fibers. Being different from metal grinding, material removal through brittle fracture plays an important role in ZrO$_2$ ceramic grinding. Most of ZrO$_2$ ceramic ferrule processes are grinding which request high processing precision. Particularly, concentricity and cylindricity of inner and outer diameter are very important. The co-axle grinding process of ZrO$_2$ ceramic ferrule is to make its concentricity all of uniform before centerless grinding. Surface integrity of ZrO$_2$ ceramic ferrule is affected by grinding conditions, and equipment. In this study, surface integrity of workpiece according to such as a change of grinding wheel speed, feed rate, regulating wheel speed and grinding force is investigate to improve the concentricity and roundness of ZrO$_2$ ceramic ferrule from many experiments. Thus, if possible be finding highly efficient and quality grinding conditions.