• Journal of Korean Society of Water and Wastewater
• /
• v.24 no.1
• /
• pp.109-117
• /
• 2010

In the present study, the degradation characteristics of Lindane by Advanced Oxidation Processes(UV/$H_2O_2$, Photo-Fenton process) were studied. The degradation efficiency of Lindane in aqueous solution was investigated at various initial pH values, Fenton's reagent concentrations and initial concentrations of Lindane. GC-ECD was used to analyze lindane. Lindane has not been degraded without application of AOPs over two hours. But, approximately 5% of lindane was degraded with UV or $H_2O_2$ alone. Lindane with UV/$H_2O_2$ process showed approximately 7% higher removal efficiency than $H_2O_2$ process. In the UV/$H_2O_2$ process, the pH values did not affect the removal efficiency. The optimal mole ratio of $H_2O_2/Fe^{2+}$ for lindane degradation is about 1.0 in Photo-Fenton process. Also, the experimental results showed that lindane removal efficiency increased with the decrease of initial concentration of lindane. Under the same conditions, the order lindane of removal efficiency is as following : Photo-Fenton process > UV/$H_2O_2$ process > $H_2O_2$ process. In addition, intermediate products were identified by GC-MS techniques. Than PCCH(Pentachlorocyclohexene) was identified as a reaction intermediate of the Photo-Fenton process.

• Textile Coloration and Finishing
• /
• v.10 no.4
• /
• pp.45-52
• /
• 1998

Reuse of wastewater become an important consideration to solve the environmental pollution problems in recent industriallzation and urbanization. Especially, he characteristic of dyeing process is subject to use much water and thus has serious problems for removal of color and organic pollutants in their wastewater. This report is divided into two main parts ： The purpose of the first part was to determine if alkaline wastewater discharged from textile dyeing operation factory could be flocculated directly by Fenton oxidation method. This study was conducted to investigate Fenton reagent dose and reaction condition of Fenton method as pretreatment for dyeing wastewater in K dyeing industry were investigated. In the second part of this research, to treat dyeing wastewater it was found that the most effective way is to use ultrafiltation and reverse osmosis at the conditions of the pH 7.0~8.0 and operating pressure of $2.5~35kg_f/cm^2$. This paper is mainly dealt with the application on reuse system of dyeing wastewater treatment using ultrafiltration and reverse osmosis membranes. The results showed that dyeing wastewater could be reused by chemical, filter and membrane sequential treatment process.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2003.11a
• /
• pp.493-500
• /
• 2003

The effect of reductive treatment with elemental iron on the extent of mineralization by Fenton oxidation was studied for the explosive 2,4,6-trinitrotoluene (TNT) and hexahydro-l,3,5-trinitro-l,3,5-triazine (RDX) using a completely-stirred tank reactor (CSTR). The results support the hypothesis that TNT and RDX are reduced with elemental iron to products that are oxidized more rapidly and completely by Fenton's reagent. Iron pretreatment enhanced the extent of TOC removal by approximately $20\%\;and\;60\%$ for TNT and RDX, respectively. Complete TOC removal was achieved for TNT and RDX solutions with iron pretreatment under optimal conditions. On the other hand, without iron pretreatment, complete mineralization of TNT and RDX solutions were not achieved even with much higher $H_2O_2$ and $Fe^{2+}$ concentrations. The bench-scale iron treatment-Fenton oxidation integrated system showed more than $95\%$ TOC removal for TNT and RDX solutions under optimal conditions. The proposed zero-valent iron-Fenton process was evaluated with pink water from the Iowa Army ammunition plant. Results from batch and column experiments show that TNT, RDX, and octahydro-l,3,5,7-tetranitro-l,3,5,7-tetrazocine (HMX) were completely removed from the pink water and that triaminotoluene (TAT) and ${NH_4}^+$ were recovered as products in reduction with zero-valent iron. By using an integrated system, $83.3\pm4.2\%$ of TOC was removed in a CSTR with 10 mM of $Fe^{2+}$ and 50 mM of $H_2O_2$. These results suggest that the reduction products of TNT and RDX are more rapidly and completely mineralized by Fenton oxidation and that a sequential iron treatment-Fenton oxidation process may be a viable technology for pink water treatment.

• Journal of Soil and Groundwater Environment
• /
• v.12 no.2
• /
• pp.27-36
• /
• 2007

A recent study showed that MTBE can be degraded by Fenton's Reagent (FR). The treatment of MTBE with FR, however, has a definite limitation of extremely low pH requirement (optimum pH $3{\sim}4$) that makes the process impracticable under neutral pH condition on which the ferrous ion precipitate forming salt with hydroxyl anion, which result in the diminishment of the Fenton reaction and incompatible with biological treatment. Consequently, this process using only FR is not suitable for in-situ remediation of MTBE. In order to overcome this limitation, modified Fenton process using NTA, oxalate, and acetate as chelating reagents was introduced into this study. Modified Fenton reaction, available at near neutral pH, has been researched for the purpose of obtaining high performance of oxidation efficiency with stabilized ferrous or ferric ion by chelating agent. In the MTBE degradation experiment with modified Fenton reaction, it was observed that this reaction was influenced by some factors such as concentrations of ferric ion, hydrogen peroxide, and each chelating agent and pH. Six potential chelators including oxalate, succinate, acetate, citrate, NTA, and EDTA were tested to identify an appropriate chelator. Among them, oxalate, acetate, and NTA were selected based on their remediation efficiency and biodegradability of each chelator. Using NTA, the best result was obtained, showing more than 99.9% of MTBE degradation after 30 min at pH 7; the initial concentration of hydrogen peroxide, NTA, and ferric ion were 1470 mM, 6 mM, and 2 mM, respectively. Under the same experimental condition, the removal of MTBE using oxalate and acetate were 91.3% and 75.8%, respectively. Optimum concentration of iron ion were 3 mM using oxalate which showed the greatest removal efficiency. In case of acetate, $[MTBE]_0$ decreased gradually when concentration of iron ion increased above 5 mM. In this research, it was showed that modified Fenton reaction is proper for in-situ remediation of MTBE with great efficiency and the application of chelatimg agents, such as NTA, was able to make the ferric ion stable even at near neutral pH. In consequence, the outcomes of this study clearly showed that the modified Fenton process successfully coped with the limitation of the low pH requirement. Furthermore, the introduction of low molecular weight organic acids makes the process more available since these compounds have distinguishable biodegradability and it may be able to use natural iron mineral as catalyst for in situ remediation, so as to produce hydroxyl radical without the additional injection of ferric ion.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.5 no.3
• /
• pp.221-227
• /
• 2007

Fenton's reagent is applied to directly decompose the ion-exchange resins, IRN-78 and the mixed resin with IRN-77. The newly applied procedures is to dry the resin first and the catalyst solution is completely absorbed into the resin, then a limited dose of $H_2O_2$ is introduced for an effective reaction between the reagents within the resin. As a characteristic on the decomposition of IRN-78, the resin mixture should be heated to $40^{\circ}C$ to induce the initial reaction and lag time is also needed for about 20 minutes until the main reaction occurs. The effectiveness of the decomposition is investigated using $CuSO_4,\;Cu(NO_3)_2\;and\;FeSO_4$ as a catalyst and the decomposition rate is compared depending on the concentration of each catalyst and the amount of $H_2O_2$. The most effective catalyst was found to be $FeSO_4$ for IRN-78 alone and the mixed resin with IRN-77, and $FeSO_4$ showed a special effect that the reaction was initiated without heating and a lag time. Furthermore, the optimum concentration of the catalyst for each resin and the mixed one is suggested in the view point of the amount of $H_2O_2$ needed and the stability of the decomposition reaction.

• The Korean Journal of Food And Nutrition
• /
• v.10 no.1
• /
• pp.37-43
• /
• 1997

This study was undertaken to evaluate as antioxidant activity against lipid peroxidation. Silymarin and silybin extracted from Silybum marianum were successively purified wit solvent fractionation by silica gel column chromatography. These isoflavonoid inhibited superoxide anion production in the xanthine oxidase system. In the rat liver microsomes, silymarin or silybin rapidly inhibited lipid peroxidation which was initiated enzymatically by reduced nicotinamide adenine dinucleotide phosphate(NADPH) or non-enzymatically by ascorbic acid or Fenton's reagent (H2O2+Fe2+). Mitochondrial lipid peroxidation was also inhibited by silymarin and silybin. silymarin and silybin inhibited on terminating radical chain reaction during lipid peroxidation in the enzymatic system of microsomes or in the linoleic acid hydroperoxide induced peroxidation system.

• Journal of Korean Society on Water Environment
• /
• v.23 no.5
• /
• pp.600-606
• /
• 2007

Livestock wastewater containing concentrated organic matters and nutrients has been known as one of the major pollutants. It is difficult to apply the conventional activated sludge process to treat livestock wastewater because of high Non-biodegradable (NBD) matter and ammonia. The objectives of this study are to remove NBD matters including aromatic compounds and ammonia in livestock wastewater using Coagulation-Fenton oxidation-Zeolite (CFZ) processes and ascertain applicable feasibility in the field through pilot plant experiment. NBD matters and color remained in the treated water were removed over 92% by Fenton oxidation as the second treatment process. Ammonia was removed by over 99.5% in the zeolite ion exchange process as the last treatment method. From $UV_{254}$, $E_2/E_3$ ratio and GC/MS analyses of treated water at each process, the aromatic compound was converted to aliphatic and aromaticity was decreased. In pilot scale test, organics and ammonia removal efficiencies were not much different from the result of lab-scale test at various operation conditions. Furthermore, reaction time and dosage of Fenton reagent in pilot scale experiment reduced by 40 min and 50% rather than in lab-scale test. $BOD_5$, $COD_{Mn}$, SS, T-N and T-P of treated water in the pilot-scale experiment also met the effluent standards.

• Journal of Soil and Groundwater Environment
• /
• v.18 no.4
• /
• pp.50-57
• /
• 2013

For the last couple of decades, the Fenton (-like) systems have been extensively studied for oxidation of organic contaminants in water. Recently, zero-valent iron (ZVI) has received attention as a Fenton catalyst as well as a reducing agent capable of producing reactive oxidants from oxygen. In this study, the ZVI-based Fenton reaction was assessed for the oxidative degradation of phenol using $ZVI/O_2$, $ZVI/H_2O_2$, ZVI/Oxalate/$O_2$ and hv/ZVI/Oxalate/$O_2$ systems. Reaction parameters such as pH and reagent dose (e.g., ZVI, $H_2O_2$, and oxalate) were examined. In the presence of oxalate (ZVI/Oxalate/$O_2$ and hv/ZVI/Oxalate/$O_2$ systems), the degradation of phenol was greatly enhanced at neutral pH values. It was found that ZVI accelerates the Fenton reaction by reducing Fe(III) into Fe(II). The conversion of Fe(III) into Fe(II) by ZVI was more stimulated at acidic pH than at near-neutral pH values.

• Korean Journal of Environmental Agriculture
• /
• v.27 no.1
• /
• pp.86-91
• /
• 2008

Dicamba(3,6-dichloro-2-methoxybenzoic acid) is used to control for pre and post-emergence of annual and perennial broad-leaf weeds. It is very soluble in water and highly mobile, acidic herbicide. So it is easily moved and detected in groundwater. Zerovalent iron(ZVI) has been used for the reductive degradation of certain compounds through amination of nitro-substituted compounds and dechlorination of chloro-substituted compounds. In this study, we investigated the potential of ZVI for the oxidative degradation of dicamba in water. The degradation rate of dicamba by ZVI was more rapidly increased in pH 3.0 than pH 5.0 solution. The degradation percentage of dicamba was increased with increasing amount of ZVI from 0.05% to 1.0%(w/v) and reached above 90% within 3 hours of reaction. As a result of identification by GC-MS after derivatization with diazomethane, we obtained three degradation products of dicamba by ZVI. They were identified 4-hydroxy dicamba or 5-hydroxy dicamba, 4,5-dihydroxy dicamba and 3,6-dichloro-2-methoxyphenol. 4-Hydroxy dicamba or 5-hydroxy dicamba and 4,5-dihydroxy dicamba are hydroxylation products of dicamba. 3,6-dichloro-2-methoxyphenol is hydroxyl group substituted compound instead of carboxyl group in dicamba. We also confirmed the same degradation products of dicamba in the Fenton reaction which is one of oxidation processes using ferric sulfate and hydrogen peroxide. But we could not find out the dechlorinated degradation products of dicamba by ZVI.

• Journal of Life Science
• /
• v.9 no.6
• /
• pp.692-697
• /
• 1999

For further removal of non-biodegradable CODs and color in biologically treated distillery waster water, we selected a chemical treatment with Fe(III) and cationic polymers and then another chemical treatment with Fenton reagent. We developed Pregenerated Bubble Flotation(PBF) to effectively remove the chemical sludge from each chemical reaction process. The flotation unit was constructed with hydraulic loading rate, 7 ㎥/$m^2$.hr. The CODMn and suspended solids (SS) in biologically treated distillery waste water were reduced by the first PBF from 310-1096 mg/L to 141-303 mg/L and from 160-990 mg/L to 48-385 mg/L, respectively. Again, after the Fenton reaction process, floated SS was skimmed off at the top of the flotation unit and the final effluent was directly discharged without any tap water dilution. The quality of final effluent can be below 40 mg/L-CODMn but IISan Distilery has been maintained effluent quality of 73 mg/L-CODMn and 10-80 mg/L-SS. The chemical cost was saved by more than 30% as compared with that of prior process.