• 대한기계학회논문집A
• /
• 제23권6호
• /
• pp.1039-1047
• /
• 1999

It is necessary to evaluate the fatigue behavior of rail steel under the multi-axial stress state to assure the railway vehicle's safety. For this purpose, the stress analysis to investigate the crack initiation criteria, static failure and fatigue behavior under mixed-mode are performed. The stress analysis results show that the initiation of the transverse fissure depends on the maximum shear stress below the surface. For the mixed mode, the fatigue crack growth behavior which is represented by the projection crack length and comparative S.I.F, ${\Delta}K_v$, shows the more conservative results. Also, its rate is lower than that of the case of the mode I, and this difference decreases with increasing the stress ratio, R.

• 대한조선학회지
• /
• 제12권2호
• /
• pp.43-58
• /
• 1975

There are many reports on fatigue crack of metallic materials but most of them relate crack propagation rate to stress intensity factor. The problem of crack propagation is not yet clarified, especially the bridge between micro and macro phenomena In this experiment rotating bending fatigue tests have been carried out with smoothed specimen of rolled steel plates including 0.2% carbon under application of three stress conditions to investigate the slip band and the crack propagation behaviour. The results obtained are as follows; 1) The length of cracks which have grown at initial crack tips can be expressed as follows; $l=Ae^{BNr}$(A,B: constant, $N_r$: cycle ratio) $\frac{dl}{dN}=\frac{AB}{N_f}{\cdot}e^{BNr}$($N_f$:fatigue life) 2) The ratio of slipped grain number to total grain number is $S_f=7{\sigma}-5.6$-5.6{\sigma}_c$($\sigma$: stress amplitude) (${\sigma}_c$: fatigue limit) 3) When the fatigue process transfers from Stage I to Stage II, the crack which propagates into specimen changes its direction from that of the maximum shear stress to the direction of perpendicular to principal stress and this is same in the circumferential direction of specimen. the crack propagation behaviors of both sides of a crack are different each other when they approach to the grain boundary.

• 한국구조물진단유지관리공학회 논문집
• /
• 제15권2호
• /
• pp.179-188
• /
• 2011

강부재의 피로가 주요원인이 되어 구조물이 붕괴되거나 교체되는 사례를 찾아보기 어렵다. 이처럼 사실상 피로에 대해서는 손상을 허용하고 있지만, 발견되는 피로균열에 대한 직접적인 상태평가는 이루어지지 않고 있다. 피로균열에 대한 진전 비진전성의 판단 및 균열진전속도의 평가가 이루어져야만, 합리적인 보수 보강 공법의 선정과 시행시기가 결정될 수 있을 것이다. 본 연구에서는 측정되는 COD(Crack Opening Displacement)를 통한 피로균열진전속도 평가법을 검토하기 위하여, 2종류의 관통 균열 시험편과 면외거셋 용접이음 시험편의 균열진전시험을 실시하였다. 그리고 실용적인 COD의 측정을 위해 변형률 게이지를 이용하는 방법에 대해 검토하였다. 그 결과, COD 측정을 통한 균열진전속도의 합리적인 평가법을 제안하였고, 변형률 게이지를 이용한 성공적인 COD 측정을 실험적으로 증명하였다.

• 한국생산제조학회지
• /
• 제6권4호
• /
• pp.80-88
• /
• 1997

An experimental investigation of the fatigue through crack growth behavior under simple stepped variable loading condition has been performed using Al7075-T651. Experiments were carried out by using cantilever bending type specimens, with chevron notches on a small electro-magnetic test machine. Tensile overloads have a retarding effect on the fatigue crack growth rates, therefore tensile overloads were used for the beneficial effect on the fatigue life. While in most cases compressive overloads have only a vanishing effect on crack growth rates, some experiments with single edge crack tension specimens reveal a marked growth retardation. The stress ratios used in this investigations varies from R=0.32 to 0.81, from R=0.04 to 0.76, from R=-0.15 to 0.73, and from R=-0.33 to 0.68 and the peak load for each case was not varied. The crack growth and crack closure were measured by Kikukawa's compliance method with a strain gauge mounted on the backside of each specimens. The results obtained are as follows. When the stepped variable load was applied, the smaller the stress ration was, the larger the delayed retardation of the crack growth rate was. The fatigue crack growh rate data obtained for through cracks were plotted well against the effective stress intensity factor range from 4.0 to 20.0MP{a^{SQRT}m}. It was found that the effective stress intensity factor range ratio was related well to the opening stress intensity factor, the maximum stress intensity factor, and crack length.

• 대한기계학회논문집
• /
• 제10권2호
• /
• pp.208-214
• /
• 1986

본 연구에서는 균열 닫힘에 관한 연구의 일환으로 5083-O 알루미늄합금을 사용하고 소규모강복조건하에서 일정진폭하중피로시험을 시행하여 이 재료의 피로균열 진전속도와 균열닫힘에 관하여 검토하였다.

• 한국해양공학회지
• /
• 제8권2호
• /
• pp.115-123
• /
• 1994

Under variable amplitude loading conditions, retardation or accelerated condition of fatigue crack growth occurs with every cycle, Because fatigue crack growth behavior varied depend on load time history. The modeling of stress amplitude with storm loading acted to ships and offshore structures applied this paper. The crack closure behavior examine by recording the variation in load-strain relationship. By taking process mentioned above, fatigue crack growth rate, crack length, stress intensity factor, and crack closure stress intensity factor were obtained from the stress cycles of each type of storm ; A(6m), B(7m), C(8m), D(9m), E(11m) and F(15m) which was wave height. It showed that the good agreement with between the experiment results and simulation of storm loads. So this estimated method of crack propagtion rate gives a good criterion for the safe design of vessels and marine structure.

• 한국해양공학회지
• /
• 제12권1호
• /
• pp.39-49
• /
• 1998

In this work, fatigue tests by axial loading were carried out to investigate the effect of stress ratio on the growth behaviors of surface fatigue crack for SM45C steel and Al 2024-T4 alloy. The growth behaviors of surface crack have been monitored during fatigue process by measuring system attached CCTV and monitor. When the growth rates of surface crack were investigate by the concept of LEFM based on Newman-Raju's .DELTA.K, the dependence of stress ratio appears both SM45C steel and Al 2024-T4 alloy. Therefore, modified stress intensity factor range, .DELTA.K' [=(1+R)/sup n/.DELTA.K] are intorduced to eliminate the dependence of stress ratio. Using .DELTA.K', it is found that the dependence of stress ratio disappears both SM45C steel and Al 2024-T4 alloy.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 춘계학술대회 논문집
• /
• pp.251-257
• /
• 1998

The distribution of fatigue crack growth rate is subjected to the measuring interval and calculated method of growth rate. In this paper, in order to establish the method of determining the distribution of fatigue crack growth rate, which ignores those influences, a series of fatigue crack growth experiments and measuring intervals of crack length calculated reasonable are presented. The main conclusions obtained are summarized as follows: 1) As a result of the ΔP constant test and ΔK constant test, it is thought that an approximate measuring interval of 0.3~0.7mm is reasonable, which allows for few errors and is little subjected to the calculated method of crack growth rate.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2001년도 가을 학술발표회 논문집
• /
• pp.375-382
• /
• 2001

This study is attempted to predict experimentally the fatigue crack propagation behavior of two-span beams with steel fibrous for various steel fibrous contents. The static tests and the fatigue tests were performed on a series of SFRC(steel fibrous reinforced concrete) to investigate the fatigue behavior of SFRC varying with the steel fibrous contents. Through this test, the diagonal cracking loads, ultimate loads, deflections, strains of concrete and steels. Fatigue crack length were measured by the eye-observation. As a result of test, A model for S-N relationship, and propagation life of fatigue crack of SFRC was proposed. The crack growth and failure of SFRC beams were studied.

• 한국강구조학회 논문집
• /
• 제22권6호
• /
• pp.589-597
• /
• 2010

강구조물의 점검시 피로균열이 발견되는 경우에는 보수 보강 시행의 결정과 구조물의 점검주기 결정을 위한 균열의 현재 상태평가와 앞으로의 균열진행 정도에 대한 정량적인 예측이 요구된다. 피로균열에 대한 손상도 평가는 파괴역학 파라미터를 이용한 균열진전속도와 취성파단의 여부 결정이 대표적인 방법으로 파괴역학에 관한 전문적인 지식과 함께 수치해석 프로그램의 활용능력이 필요하다. 이에, 본 연구에서는 피로손상도 평가 방법에 관한 다양성을 확보하고, 파괴역학에 대한 전문적인 지식이 없는 기술자가 피로균열에 의한 강구조물의 손상도를 간편하게 평가 할 수 있는 방법을 개발하기 위한 첫 단계로, 관통균열 시험편을 이용한 균열진전시험을 실시하였다. 그리고 피로균열 표면으로부터 측정된 COD(Crack Opening Displacement)의 크기와 측정위치를 이용하여, 균열진전속도를 추정하기 위한 파라미터를 도출하고, 그 타당성을 분석하였다. 그리고 관통균열이 있는 시험편의 형상, 응력범위, 그리고 응력비에 상관없이 COD를 이용하여 피로균열진전속도를 추정할 수 있는 방법을 제시하였다.