• 한국신뢰성학회지:신뢰성응용연구
• /
• 제11권3호
• /
• pp.293-303
• /
• 2011

Reliability Prediction using MIL-HDBK-217F has some restrictions due to its one modeling basis. One of the restrictions is caused by selecting one operating environment of a system, which is chosen regardless of its detailed conditions, e.g., external impact and vibration. Especially, an equipment, which is installed on a mobile vehicle though its movement is quasi-static, is controversial to designate its environment as ground mobile($G_M$), rather than ground fixed($G_F$). In this paper, failure rates were compared, which are computed using several moving time rates to total operating time. RiAC-HDBK-217Plus was used as the basic calculation model. In addition, $G_F$ conditioned failure rate was evaluated by comparing with that under $G_M$ environment but fixed state.

• Structural Engineering and Mechanics
• /
• 제20권1호
• /
• pp.1-20
• /
• 2005

The present paper deals with the seismic response analysis and the evaluation of most likely failure modes for a water storage structure. For the stress analysis, a 3-D mathematical model has been adopted to represent the structure appropriately. The structure has been analyzed for both static and seismic loads. Seismic analysis has been carried out considering the hydrodynamic effects of the contained water. Based on the stress analyses results, the most likely failure modes viz. tensile cracking and compressive crushing of concrete for the various structural elements; caused by the seismic event have been investigated. Further an attempt has also been made to quantify the initial leakage rate and average emptying time for the structure during seismic event after evaluating the various crack parameters viz. crack-width and crack-spacing at the locations of interest. The results are presented with reference to peak ground acceleration (PGA) of the seismic event. It has been observed that, an increase in PGA would result in significant increase in stresses and crack width in the various structural members. Significant increase in initial leakage rate and decrease in average emptying time for the structure has also been observed with the increase in PGA.

• 한국지반신소재학회논문집
• /
• 제16권1호
• /
• pp.41-52
• /
• 2017

본 연구에서는 월류에 의한 붕괴 메커니즘의 규명을 위해 모형제방(제방고 0.4~0.8m)과 실물제방(제방고 1.0m)을 대상으로 월류 붕괴실험을 수행하였다. 월류에 의한 제방붕괴는 1단계에서는 월류에 의해 비탈표면에서 세굴이 발생되었으며, 월류의 유속은 완만히 증가되었다. 2단계에서는 붕괴단면이 커지고 유속도 급격히 증가되었다. 3단계에서는 월류에 의해 제방 단면이 완전히 붕괴되고 붕괴면적이 넓어져 유속이 상대적으로 감소되었다. 월류에 의한 제방의 붕괴각(${\theta}$)은 큰 자중, 감소된 전단저항력 및 월류의 흐름에 의한 추가 소류력으로 인해 랭킨토압의 사면붕괴각보다 크게 나타났다. 제방고(H)가 증가될수록 월류에 의한 제방의 월류 유속(${\upsilon}$)이 증가되었으며, 이로 인해 소류력이 추가로 작용되어 제방의 붕괴각(${\theta}$)과 붕괴면적(A)이 함께 증가되었다. 모형실험과 실물실험에 사용된 모래 시료가 동일한 입경크기로 한계세굴유속이 같아 월류 유속변화에 의해 세굴 특성이 지배되는 것으로 나타났다.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제12권1호
• /
• pp.1-12
• /
• 2012

The quality of a part has directly effect on part reliability. In the basis of MIL-HDBK-217F model, it is the determined rule that part's quality level should follow its nominal one written in its specification. If quality information is unknown, quality level of the part should be determined as 'Lower'. However, the prediction model is said to be short in reflecting parts applying 'state-of-the-art' technology and result in over-estimated failure rate by some reliability-related authorities or research institutes. In this study, the reliability prediction results by the model of MIL-HDBK-217F and Telcordia SR-332 are compared and analyzed to verify whether the statement is reasonable or not.

• 한국안전학회지
• /
• 제39권1호
• /
• pp.33-40
• /
• 2024

This study analyzes the impact of regular preventive maintenance (PM) on reducing the failure rate and occurrence of falling accidents of industrial overhead doors. A reliable safety device model with an additional safety device, which is installed to replace a defective one, is proposed. The research methodology involves collecting breakdown and falling accident records, comparing and analyzing data before and after regular PM implementation, and experimenting with two types of retrofittable safety devices. Key findings are as follows. 1. Regular PM implementation significantly reduces the failure rate of old overhead doors. 2. A parallel structured model with two alternative safety devices can minimize falling accident risks. The study's contributions include the following. 1. The positive impact of PM on extending overhead door lifespan is quantified. 2. A general safety device model that can be retrofitted and used as replacement with a fail-safe function is proposed.

• International Journal of Reliability and Applications
• /
• 제17권2호
• /
• pp.149-158
• /
• 2016

We are enjoying a very comfortable life thanks to modern civilization, however, comfort is not guaranteed to us. Development of software system is a difficult and complex process. Therefore, the main focus of software development is on improving the reliability and stability of a software system. We have become aware of the importance of developing software reliability models and have begun to develop software reliability models. NHPP software reliability models have been developed through the fault intensity rate function and the mean value functions within a controlled testing environment to estimate reliability metrics such as the number of residual faults, failure rate, and reliability of the software. In this paper, we present a new NHPP software reliability model with Burr Type III fault detection rate, and present the goodness-of-fit of the fault detection rate software reliability model and other NHPP models based on two datasets of software testing data. The results show that the proposed model fits significantly better than other NHPP software reliability models.

• 대한조선학회논문집
• /
• 제53권2호
• /
• pp.85-91
• /
• 2016

The most important factor in the structural design of ships and offshore structures operating in arctic region is ice load, which results from ice-structure interaction during the ice collision process. The mechanical properties of ice related to strength and failure, however, show very complicated aspect varying with temperature, volume fraction of brine, grain size, strain rate and etc. So it is nearly impossible to establish a perfect material model of ice satisfying all the mechanical characteristics completely. Therefore, in general, ice collision analysis was carried out by relatively simple material models considering only specific aspects of mechanical characteristics of ice and it would be the most significant cause of inevitable errors in the analysis. Especially, it is well-known that the most distinctive mechanical property of ice is high dependency on strain rate. Ice shows brittle attribute in higher strain rate while it becomes ductile in lower strain rate range. In this study, the simulation method of ice collision to ship hull using the nonlinear dynamic FE analysis was dealt with. To consider the strain rate effects of ice during ice-structural interaction, strain rate dependent constitutive model in which yield stress and hardening behaviors vary with strain rate was adopted. To reduce the huge amount of computing time, the modeling range of ice and ship structure were restricted to the confined region of interest. Under the various scenario of ice-ship hull collision, the structural behavior of hull panels and failure modes of ice were examined by nonlinear FE analysis technique.

• Communications for Statistical Applications and Methods
• /
• 제17권1호
• /
• pp.99-106
• /
• 2010

In this paper, we present two methods for obtaining prediction intervals for the times to failure of units censored in multiple stages in a progressively censored sample from proportional hazard rate models. A numerical example and a Monte Carlo simulation study are presented to illustrate the prediction methods.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.275-278
• /
• 2005

INCONEL 718, nickel based superalloy, has good formability, high strength, excellent corrosion resistance and mechanical properties at high temperature. Owing to theses attractive properties, it finds use in applications such as combustion system, turbine engines and nuclear reactors. In such applications, components are typically required to be tolerant of high stress impact loading. This may cause material degradation and lead to catastrophic failure during service operation. In order to design optimal structural parts made of INCONEL 718, accurate understanding of material's mechanical properties, dynamic behavior and fracture characteristic as a function of strain rates are required. This paper concerned with the dynamic material properties of the INCONEL 718 for the various strain rates. The dynamic response of the INCONEL 718 at intermediate strain rate is obtained from the high speed tensile test machine test and at the high strain rate is from the split Hopkinson pressure bar test. Based on the experimental results, the effects of strain rate on dynamic flow stress, work hardening characteristics, strain rate sensitivity and elongation to the failure are evaluated. Experimental results from both quasi-static and high strain rate up to the 5000/sec are interpolated in order to construct the Johnson-Cook model as the constitutive relation that should be applied to simulate and design the structural parts made of INCONEL 718.

• 소성∙가공
• /
• 제14권6호
• /
• pp.559-564
• /
• 2005

INCONEL 718, nickel based superalloy, has good formability, high strength, excellent corrosion resistance and mechanical properties at high temperature. Owing to theses attractive properties, it is utilized in applications such as combustion system, turbine engines and nuclear reactors. In such applications, components are typically required to be tolerant of high stress impact loading. This may cause material degradation and lead to catastrophic failure during service operation. Accurate understanding of material's mechanical properties with various strain rates is required in order to guarantee the reliability of structural parts made of INCONEL 718. This paper is concerned with the dynamic material properties of the INCONEL 718 at various strain rates. The dynamic response of the INCONEL 718 at the intermediate strain rate is obtained from the high speed tensile test and at the high strain rate is from the split Hopkinson pressure bar test. The effect of the strain rate on dynamic flow stress, work hardening characteristics, strain rate sensitivity and elongation to the failure is evaluated with the experimental results. Experimental results from both the quasi-static and the high strain rate up to 5000/sec are interpolated in order to construct the Johnson-Cook model as the constitutive relation that should be applied to simulate and design the structural parts made of rNCONEL 718.