• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.8
• /
• pp.693-699
• /
• 2003

To improve thermal stability of Teflon FEP which is the most widely used materials for electret application, Teflon AF film of 1 $\mu\textrm{m}$ thick was spin coated on FEP film and the charge storage properties were investigated. The surface potential depend on aging temperature. Thermal Stimulated Current(TSC), Atomic Force Microscopy(AFM), and Fourier Transform-Infrared Spectroscope(FT-lR) measurements were carried out. It is shown that the AF/FEP dual film have more higher electrical property and thermal stability than that FEP film have caused by charge stored at interface of AF and FEP.

• Korean Membrane Journal
• /
• v.10 no.1
• /
• pp.33-38
• /
• 2008

In this study periodic water-back-flushing using permeate water was performed to minimize membrane fouling and to enhance permeate flux in tubular ceramic micro filtration system for Gongji stream water treatment in Chuncheon city. The filtration time (FT) 2 min with periodic 6 sec water-back-flushing showed the highest value of dimensionless permeate flux ($J/J_0$), and the lowest value of resistance of membrane fouling ($R_f$), and we acquired the highest total permeate volume ($V_T$) of 7.44L. Also in the results of BT effect at fixed FT 10 min, BT (back-flushing time) 20 sec showed the lowest value of $R_f$ and the highest value of $J/J_0$, and we could be obtained the highest $V_T$ of 8.04 L. Consequently FT 10 min and BT 20 sec could be the optimal condition in Gongji stream water treatment. Then the average rejection rates of pollutants by our tubular ceramic MF system were 93.8% for Turbidity, 20.7% for $COD_{Mn}$, 39.2% for $NH_3$-N and 31.5% for T-P.

• Korean Membrane Journal
• /
• v.8 no.1
• /
• pp.50-57
• /
• 2006

We treated lake water by ceramic ultrafiltration membranes and found the optimal backflushing period and trans-membrane pressure (TMP) of periodic water-backflushing system. The optimal filtration time interval at fixed BT = 3 sec was 30 for A002 membrane in all viewpoints of $J/J_0,\;R_f$, and $V_T$, and we could acquire the highest $V_T$ value in the membranes used here. However, the highest $V_T$ was acquired at FT = 60 sec for M9, and at FT = 90 sec for C005 membrane. Then the lower TMP reduced the membrane fouling during filtration of lake water, and could maintain the higher permeate flux compared with the initial flux. However, the largest value $V_T$ could be obtained at the highest TMP condition for M9 membrane at fixed FT = 60 sec and BT = 3 sec. The quality of treated water in our UF ceramic system was Turbidity = $0.20{\sim}4.88NTU$, $COD_{Mn} = 0.00{\sim}2.58 mg/L$, $TDS = l8{\sim}71 mg/L$, and $NH_3-N = 0.004{\sim}1.689 mg/L$.

• Membrane Journal
• /
• v.18 no.4
• /
• pp.325-335
• /
• 2008

In this study, we used multi-channels ceramic membrane having larger permeate volume per unit time rather than tubular membrane. The hybrid process for advanced drinking water treatment was composed of granular activated carbons (GAC) packing between module inside and outside of multi-channels microfiltration membrane. Instead of natural organic matters (NOM) and fine inorganic particles in natural water source, modified solution was prepared with humic acid and kaolin. Kaolin concentration was fixed at 30mg/L and humic acid was changed as $2{\sim}10\;mg/L$ to inspect effect of organic matters. As a result, both resistance of membrane fouling ($R_f$) and permeate flux (J) were highly influenced by concentration of humic acid. Also, in result of water-back-flushing period (FT) effect, the shorter FT was the more effective to reduce membrane fouling and to enhance permeate flux because of frequent water-back-flushing. However, the optimal FT condition was 8 min when operating costs were considered. Then, the hybrid process using multi-channels ceramic membrane and GAC was applied to lake water treatment. As a result, average treatment efficiencies in our experiment using the hybrid process were 98.02% for turbidity, 75.64% for $UV_{254}$ absorbance, 7.18% for TDS and 84.73% for $COD_{Mn}$.

• Asian-Australasian Journal of Animal Sciences
• /
• v.6 no.2
• /
• pp.219-223
• /
• 1993

A total of 333 calves were evaluated for carcass quality traits including: dressing percentage (DP), yield grade (YG), marbling score (MS), fat thickness (FT) and percent body fat (PF). Mating types included straightbred Angus (A) and Santa Gertrudis (S), the reciprocal crosses of these two breeds and Gelbvieh (G) ${\times}$ Angus. The year of birth, slaughter group and dam breed were found to have greatly influenced DP. Mating types had no effect on DP. For YG, sire breed, sire within sire breed and slaughter group were important. Crossbreds of A ${\times}$ S had the highest YG followed by A purebreds. Crossbreds of G ${\times}$ A had the lowest YG. Sire breed, dam breed and the slaughter group has significantly affected the MS. Sire breed, sire nested within sire breed and slaughter group were found to have greatly influenced the FT. Sires and dams of A produced the greatest FT while sires of G produced the lowest. Slaughter group 2 (slaughtered at 433 days of age) had a greater FT than group 1 (slaughtered at 393 days of age). For PF, sire breed, sire within sire breed, dam breed and slaughter group had significant effects. A purebreds had the largest PF while S purebreds and G ${\times}$ A crosses had the least.

• Journal of the Korean Chemical Society
• /
• v.44 no.4
• /
• pp.337-342
• /
• 2000

Many kinds of experiments were performed for the quality control of antifoaming agents used in thermal power pIants of KEPCO. We tried to establish more convenient ans more accurate quantitative analytical method to determine the amount of silicone oil in silicone oil type antifoaming agent regardless of the amount and/or the type of involved surface active agents. First, the amount of silicone oil was measured by gravimetric method or centrifugal method using very simple apparatus, and then was compared to the results of FT-lR spectroscopy. The centrifugal method was turned out a poor method depending upon the recovery test and virtual experiments. Some antifoaming agents showed very similar results between gravimetric method and spectroscopic methods, and the others gave very different results. We concluded that FT-lR spectroscopy is the most convenient and reliable methodto determine the amounts of silicone oil in the antifoaming agents.

• Journal of the Korean Society of Radiology
• /
• v.84 no.2
• /
• pp.427-440
• /
• 2023

Purpose This study aimed to investigate the correlation between the fat signal fraction (FF) of the fat-dominant bone tissue of the knee joint, measured using the MRI Dixon method (DIXON) technique, and bone mineral density (BMD). Materials and Methods Among the patients who underwent knee DIXON imaging at our institute, we retrospectively analyzed 93 patients who also underwent dual energy X-ray absorptiometry within 1 year. The FFs of the distal femur metaphyseal (Fm) and proximal tibia metaphyseal (Tm) were calculated from the DIXON images, and the correlation between FF and BMD was analyzed. Patients were grouped based on BMD of lumbar spine (L), femoral neck (FN), and common femur (FT) respectively, and the Kruskal-Wallis H test was performed for FF. Results We identified a significant negative correlation between TmFF and FN-BMD in the entire patient group (r = -0.26, p < 0.05). In female patients, TmFF showed a negative correlation with FN-BMD, FT-BMD, and L-BMD (r = -0.38, 0.28 and -0.27, p < 0.05). In male patients, FmFF was negatively correlated with only FN-BMD and FT-BMD (r = -0.58 and -0.42, p < 0.05). There was a significant difference in the TmFF between female patients grouped by BMD (p < 0.05). In male patients, there was a significant difference in FmFF (p < 0.05). Conclusion Overall, we found that FF and BMD around the knee joints showed a negative correlation. This suggests the potential of FF measurement using DIXON for BMD screening.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.21 no.2
• /
• pp.129-139
• /
• 1995

To confirm the usefulness of partial least-squares(PLS) and multiple scattering correction(MSC) method for quantitation of surfactants in [quantitative methods using FT-lR, reconsitituted mixtures of LAS, MES and ELA-9 were tested. Each mixture was dissolved in 50% EtOH, dried, and applied to the KBr cell. From the IR spectra of these mixture, the variance spectrum was obtained. After repeated calibrations for the various regios of this spectrum, we found that 1245-1130cm-1 and 1070-1010cm-1 showed the strong correlation with each component of the sample mixture: all the correlation coefficients were 1.000 and quantitative errors did not exceed 0.32%. From this result, we concluded that PLS method and MSC method are very useful and can be successfully applied to Quality control.

• Environmental Engineering Research
• /
• v.25 no.4
• /
• pp.561-570
• /
• 2020

In the present study, dye decolorizing bacteria were isolated from water and soil samples, collected from textile industries in Jodhpur province, India. Two bacterial species namely, Bacillus pumilis and Paenibacillus thiaminolyticus were screened and identified based on biochemical characterization. The degradation efficiency of these two microorganisms was compared through optimization of pH, incubation time, initial dye concentration and inoculum size. B. pumilis and P. thiominolyticus were able to degrade 61% and 67% Red HE3B, 81% and 75% Orange F2R, 49.7% and 44.2% Yellow ME4GL and 61.6% and 59.5% Blue RC CT dyes of 800mg/l concentration respectively. The optimum pH and time were found to be 8 within 24 hours. The FT-IR analysis confirmed that microorganisms were able to degrade toxic azo dyes into a non-toxic product as proved through structural modifications to analyze chemical functions in materials by detecting the vibrations that characterize chemical bonds. It is based on the absorption of infrared radiation by the microbial product. Therefore, Bacillus pumilis and Paenibacillus thiaminolyticus are a promising tool for decolorization of dyes due to its potential to effectively decolorize higher azo dye concentrations (10-800 mg/L) and can be exploited for bioremediation.

• Journal of Biomedical Engineering Research
• /
• v.17 no.4
• /
• pp.479-490
• /
• 1996

To utilize collagen as an implantable biomateriall the mcct widely used bovine skin origin Type I collagen was investigated Pepsin treated, Type I atelocollagen was extracted and crosslinked by the ultraviolet(W) ray with wavelength of 254nm or by various concentrations of glutaraldehyde to produce collagen membranes. The crosslink rates of the specimens were observed by a polarized light microscope, a scanning electron microscope, and a Fourier transform infrared (FT-lR) spectrometer. The followings are concluded 1. The collagen membranes produced by both 2.5% glutaraldehyde solution and 254nm UV ray irra- diation demonstrated similar morphologies on polarized light microscopic and scanning electron microscopic views. 2. The chemical structures of the crosslinked membranes by glutaraldehyde over 2.5% in concentrations revealed similar intensities to that of the UV ray irradiated one in FT-lR investigation. 3. To obtain optimal croulink in bovine stalin origin Type I atelocollagen, 2.5% glutaraldehyde solution or UV ray irradiation with 254nm wavelength is acceptable.