• The Journal of the Acoustical Society of Korea
• /
• v.30 no.3
• /
• pp.115-122
• /
• 2011

In this paper, we present a method to estimate an accurate real-time sound source direction based on time delay of arrival by using generalized cross correlation with four cross-type microphones. In general, existing systems have two disadvantages such as system embedding limitation due to the necessity of data acquisition for signal processing from microphone input, and real-time processing difficulty because of the increased number of channels for sound direction estimation using DSP processors. To cope with these disadvantages, the system considered in this paper proposes hardware design for enhanced real-time processing using microphone array signal processing. An accurate direction estimation and its design time reduction is achieved by means of an efficient hardware design using spatial segmentation methods and verification techniques. Finally we develop a system which can be used for embedded systems using a sound codec and an FPGA chip. According to experimental results, the system gives much faster real-time processing time compared with either PC-based systems or the case with DSP processors.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.6B
• /
• pp.630-640
• /
• 2009

The thesis suggests hand-held equipment to overhaul for mobile TFT LCD/OLED module of high-performance. The established module equipment to overhaul could distinguish outputting video data to module for distinguishing flicker, but it is impossible with low system. In this thesis, supporting system could check the various supplement functions from bringing equipment to overhaul without changing design of FPGA or H/W the module various size for equipment to overhaul for module of high-performance coincidently. The system includes hand-held equipment to overhaul, test software embedded and software a base personal computer and have designed to output, save, and certify all contents of module test of hand-held equipment to overhaul to interface universal serial bus. Setting up 9 items that represent for efficient verification of the proposed system have been possible confirmation with TFT LCD/OLED module of high-performance, establishment scan time, creation gamma, changing register, supporting interface, and multi inch modules.

• Proceedings of the Korean Information Science Society Conference
• /
• 2006.06a
• /
• pp.226-228
• /
• 2006

In this paper we describe a simulation and development framework for designing mobile 3D graphics architectures. We are developing a simple and flexible simulation and verification environment (SVE) that uses gITrace's ability to intercept and redirect an OpenGL/ES streams. In combination wlth gITrace to trace OpenGL/ES commands, the SVE simulates the behavior of mobile 3D graphics pipeline during playback of traces, and then produces the second geometry trace that can be used as a test vector for the Verilog/HDL RT-level model. By comparing the frame-by-frame results, we can conduct architectural verification. To demonstrate the functionality of the SVE, we show the implementation of the verified mobile 3D architecture on a FPGA board. For this, we also present an application development environment (ADE) includes a mobile graphics API and a device driver interface (DDI). The proposed two software environments, the SVE and the ADE could be used fer developing and testing mobile applications, architectural study and speculative hardware designs.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.6
• /
• pp.1533-1545
• /
• 1996

In this paper, the design and implementation of echo canceller with new variable step size algorithm is discussed. The method used in the new algorithm is to periodically adopt the test function which helps an optimal coefficient tracking. This algorithm outperforms LMS and VS algorithms in convergence speed and steady state error. As the period of test function is decreased, the speed of convergence is improved, but the number of calculation is increased, then the trade off between these parameters must be considered. Simulation results show new algorithm outperforms LMS and VS algorithms in convergence rate. For the design of hardware, circuit is designed with VHDL, and synthesized with Act1 withc is a FPGA library of ActelTM in use of synovation of InterGraph$^{TM}$. Verification of the synthesized circuit is carried out with simulator DLAB. The circuit based on the algorithm which is suggested in this paper calculated 7 radix places of inary number. A simulation data for the verification is based on the data of algorithm simulation. When the same input data is applied to the both simulation, output results of circuit simulation had slight difference in compare with that of algorithm simulation. The number of used gate is about 5,500 and We have 5.53MHz in maximum frequency.y.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.11
• /
• pp.1655-1662
• /
• 1993

In this paper we discuss three algorithms-Direct, Successive, and Recursive-on parallel CRC(Cyclic Redundancy Check) verification. The algorithms are derived by combining the byte-syndromes precomputed from the generator polynomial. These algorithms are compared in terms of the amount of hardware and the speed of operation. Since the algorithms can be generalized easily, we took the ATM cell delineation example for easier description. As an application of the algorithm Recursive, an ATM cell delineation module suitable for STM-1 transmission has been successfully realized through commercially available field programmable gate arrays.

• Journal of IKEEE
• /
• v.26 no.3
• /
• pp.437-444
• /
• 2022

This paper proposes a CRC error verification method for SPI and I2C buses of automotive semiconductors. In automotive semiconductors, when an error occurs in communication and an incorrect value is transmitted, fatal results may occur. Unlike LIN communication and CAN communication, in communication such as SPI and I2C, there is no frame for detecting an error, so some definitions of new standards are required. Therefore, in this paper, the CRC error detection mode is newly defined in the SPI and I2C communication protocols, and the verification is presented by designing it in hardware.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.4
• /
• pp.43-54
• /
• 2007

This paper presents design and verification of a face detection hardware for real time application. Face detection algorithm detects rough face position based on already acquired feature parameter data. The hardware is composed of five main modules: Integral Image Calculator, Feature Coordinate Calculator, Feature Difference Calculator, Cascade Calculator, and Window Detection. It also includes on-chip Integral Image memory and Feature Parameter memory. The face detection hardware was verified by using S3C2440A CPU of Samsung Electronics, Virtex4LX100 FPGA of Xilinx, and a CCD Camera module. Our design uses 3,251 LUTs of Xilinx FPGA and takes about 1.96${\sim}$0.13 sec for face detection depending on sliding-window step size, when synthesized for Virtex4LX100 FPGA. When synthesized on Magnachip 0.25um ASIC library, it uses about 410,000 gates (Combinational area about 345,000 gates, Noncombinational area about 65,000 gates) and takes less than 0.5 sec for face realtime detection. This size and performance shows that it is adequate to use for embedded system applications. It has been fabricated as a real chip as a part of XF1201 chip and proven to work.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.8 no.1
• /
• pp.17-24
• /
• 2013

In this paper, we present a multi-core processor including multimedia specific instructions to process multimedia data efficiently in the mobile environment. Multimedia specific instructions exploit subword level parallelism (SLP), while the multi-core processor exploits data level parallelism (DLP). These combined parallelisms improve the performance of multimedia processing applications. The proposed multi-core processor including multimedia specific instructions is implemented and tested using a Xilinx ISE 10.1 tool and SoCMaster3 testbed system including Vertex 4 FPGA. Experimental results using a fire detection algorithm show that multimedia specific instructions outperform baseline instructions in the same multi-core architecture in terms of performance (1.2x better), energy efficiency (1.37x better), and area efficiency (1.23x better).

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.735-738
• /
• 2005

This paper presents an AMBA-based IP that can perform the deblocking filtering operations required in the H.264 video compression. The deblocking filter circuit was optimized for area and performance. The AHB wrapper was added to the circuit to interface with the AMBA-based platform. The AMBA-compliant operation of the proposed IP was verified on the platform board with Xilinx Virtex2 XC2V600 FPGA and ARM9 processor.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.129-131
• /
• 2004

Elliptic Curve Cryptography (ECC) coprocessors support massive scalar multiplications of a point. We research the design for multi-segment multipliers in fixed-size ECC coprocessors using the multi-segment Karatsuba algorithm on GF($2^m$). ECC coprocessors of the proposed multiplier is verified on the SoC-design verification kit which embeds ALTERA EXCALIBUR FPGAs. As a result of our experiment, the multi-segment Karatsuba multiplier, which has more efficient performance about twice times than the traditional multi-segment multiplier, can be implemented as adding few H/W resources. Therefore the multi-segment Karatsuba multiplier which satisfies performance for the cryptographic algorithm, is adequate for a low cost embedded system, and is implemented in the minimum area.