• Journal of the Korean Society for Precision Engineering
• /
• v.2 no.3
• /
• pp.84-91
• /
• 1985

This paper proposes the theory for the Low Cost Automation (LCA) as a intermediate process of the factory automation, where the SCA is new adaptation for the improving productivity without changing the current product lines. And also this paper deals with the case study for the predictable effects and technical method at the extruding cable lines. As the results, the implementation of the LCA theory could be acomplished saving materials and man power, improving reliability and productivity. For this facilities, it cost within 5% extra expense of a extruding cable line systems. And it could be refund in six months.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.04a
• /
• pp.35-39
• /
• 2000

Three-dimensional rigid plastic FEM is adopted to analyze the extruding-bulging process of tee tubes. Equivalent strain-rate stress distributions and the deformation characteristic in extruding-bulging process of tee tubes are revealed which provide scientific and reliable basis for correctly designing technologcial scheme and rationally selecting parameters. meanwhile some approaches for three-dimensional rigid plastic FEM are also discussed in this paper

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.10a
• /
• pp.117-118
• /
• 2016

This paper evalutes properties of extruding cement panel using Ca-extracted convert slag and air-cooled blast furnace slag. Flexural strength of extruding cement panel has measured in air dry and autoclave curing as basic study for use as silicious source. As a result, when Ca-extracted converter slag replaces 25% in autoclave curing, flexural strength measures 13.1MPa better than panel control mix. In result of using air-cooled blast furnace slag, Ca-extracted air-cooled blast furnace slag dose not show increase of flexural strength.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.13-14
• /
• 2017

In this paper, research for use possibility as silica source of waste concrete powder discharged from direct and indirect carbonation has progressed. For the research, properties on the extruding panel using waste concrete powder with high silica content is evaluated. As the results, compressive strength of specimen is increased 24% compared to control specimen when waste concrete powder replaced 50%, that is discharged from carbonation process, as silica source.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.105-109
• /
• 1996

The calculation of the total power required at the Continuous Extrusion Forming(CONFORM) has been performed by the theoretical analysis of three transformation regions(primary grip length and extrusion grip length, flashing). In this study, that was performed by five transformation regions(biting, upsetting, filling, extruding, flashing)and four transformation regions(biting, upsetting and filling, extruding, flashing) and then results of theoretical analyses were compared with experimental results. Results of analysis by four and five transformation regions than that of three transformation regions in the CONFORM showed in a good agreement with experimental results.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.712-713
• /
• 2006

We successfully developed Al-Si-Transition Metal (TM) -Rare Earth (RE) Powder Metallurgy (P/M) alloy with fine microstructure, which has high strength at high temperature. This material was compacted rapidly solidified powder and directly consolidated by hot extruding or forging. Before consolidating, rapid heating was performed on powder compaction in order to keep the fine microstructure in powder state. We have also investigated the processing conditions of this new alloy by computing simulations and experiments.

• Elastomers and Composites
• /
• v.14 no.4
• /
• pp.253-259
• /
• 1979

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.285-288
• /
• 2003

The bending phenomenon during extruding one product using four billets can be obtain by the difference of hole diameters in the multi-hole container. The difference of hole diameter caused the difference of billet amount inserted in the die cavity. As results, it can bend during extruding products by the different amount of two billets and by the cohesion of billets in the porthole dies cavity. And the bending curvature can be controlled by the size of holes and billets. The experiments using aluminium material had been done for the rectangular and square curved tube product. The results of the experiment show that the curved aluminum tube product can be bended by the extru-bending process without the defects such as the distortion of section and the thickness change of the wall of tube and the folding and wrinkling. The curvature of product is affected by shape of cross section and the difference of billet diameters. It is known that the welding and extruding and bending can be done simultaneously in the die cavity when a rectangular hollow curved tube would be extruded by porthole dies using four different size billets made of aluminum material.

• Agricultural and Biosystems Engineering
• /
• v.6 no.2
• /
• pp.70-76
• /
• 2005

Seed, stem and sprout of F. tataricum were separately milled using the ultra fine mill under the same condition to investigate the effect of roasting or extruding on the particle size, microstructure and water solubility of dietary fiber. The mean particle size of MR (roasting) is increased in stem and sprout, and that of ME (extruding) is increased in seed, compared to that of control. The microscopic views of seed show that control has the spherical shape but ME the larger and irregular shape, and those of stem and sprout show that control has the needle like shape but ME more rounded shape. Water solubility index of ME is much higher than that of control or MR in seed, stem and sprout. It shows that seed, stem and sprout are damaged more in extruding than in roasting, and the starch and cell wall structure must be destroyed to change the water insoluble dietary fiber into the water soluble dietary fiber.

• Food Science and Biotechnology
• /
• v.18 no.6
• /
• pp.1336-1341
• /
• 2009

Quantitative changes in functional constituents of waxy corn (Zea mays L.) by 5 different thermal pretreatments, including roasting, steaming, microwave, puffing, and extruding, were determined and compared with those of the raw waxy corn. There were no significant differences in fatty acid compositions among the corn treated with 5 thermal treatments. Levels of $\alpha$- and $\gamma$-tocopherols, soluble amino acids, and phytosterols decreased by thermal treatments, while those of p-coumaric and ferulic acids considerably increased by thermal treatments. In particular, the contents of tocopherols and phytosterols, and souble amino acid decreased significant in the steaming and puffing processes, respectively, whereas those of 2 free cinnamic acids increased significantly in the steaming and puffing processes. The extruding process showed smaller quantitative changes in tocopherols, phytosterols, and hydroxycinnamic acid derivatives compared to other heat pretreatments. These results suggest that the extruding process have a positive effect on valuable phytochemicals in waxy corn.