• The Journal of the Acoustical Society of Korea
• /
• v.39 no.2
• /
• pp.98-104
• /
• 2020

A method to reduce the Contraction and Expansion (CE) noise occurred in an air conditioner is investigated. The noise is measured during the cooling and heating phases in a temperature and humidity chamber to identify the generating phenomenon of CE noise of the air conditioner and the decomposition method is used to estimate its occurrence location. The CE noise of an air conditioner is known to be caused by a stick-slip phenomenon generated by joints of parts connected to the lower decor. Thus a friction experiment was conducted to investigate noise inducing factors. Also, this study established evaluation criteria to effectively analyze the results from friction experiments. Experimental results indicate that increasing surface roughness on both sides of joints is effective. Accordingly, the effect of increased surface roughness on joints of upper and lower decor of air conditioners is evaluated to see its feasibility in a temperature and humidity chamber.

• Economic and Environmental Geology
• /
• v.30 no.2
• /
• pp.175-183
• /
• 1997

The concrete structure can be easily damaged due to alkali-aggregates reaction. There are several methods to identify alkali reactivity of aggregates. The most reliable method is mortar-bar test, but it takes 3 to 12 months for whole test. The authors applied "rapid method" which takes only 7 days for this test. The result of this rapid method follows; expansion ratio of mortar bar for natural aggregates taken at the Youngsan River ranges from 0.197 to 0.489%, but that from Changseong Lake has low expansion ratio of 0.147%, which is below the limit of allowance, 0.168%. Those from the Seomjin River range from 0.173 to 0.22%, and those from the Keum River range from 0.078% to 0.111%. In the case of higher expansion ratio than 0.168%, aggregates must be used with cement containing low alkali content or adding material consuming the alkali content of cement, for example, fly ash and silica fume, etc.. Most of natural aggregates in Cheolla area have no problem in physical properties, particularly the abrasion ratio is below 40%, the limit of allowance. The natural aggregate from Cheolla area consists mostly of gneiss, granite and volcanic rocks. The major alkali reactive materials are quartz mineral with undulatory extinction in gneiss and granite, and amorphous silica in volcanic rocks. Even if a certain aggregate consists of the same kind of rocks and has similar rock composition each other, content of alkali reactivity material can be various, because rock formation is locally different according to temperature and pressure. Therefore every rock type must be physically and chemically identified before using for aggregates.

• Journal of the Korea Society of Computer and Information
• /
• v.24 no.10
• /
• pp.25-32
• /
• 2019

In this paper, we propose a method to apply the attack surface expansion through decoy traps to a protected server network. The network consists of a large number of decoys and protected servers. In the network, each protected server dynamically mutates its IP address and port numbers based on Hidden Tunnel Networking that is a network-based moving target defense scheme. The moving target defense is a new approach to cyber security and continuously changes system's attack surface to prevent attacks. And, the attack surface expansion is an approach that uses decoys and decoy groups to protect attacks. The proposed method modifies the NAT table of the protected server with a custom chain and a RETURN target in order to make attackers waste all their time and effort in the decoy traps. We theoretically analyze the attacker success rate for the protected server network before and after applying the proposed method. The proposed method is expected to significantly reduce the probability that a protected server will be identified and compromised by attackers.

• The Journal of the Convergence on Culture Technology
• /
• v.8 no.4
• /
• pp.407-413
• /
• 2022

In this study, the empirical formula for evaluating cable tension based on long-term measurement for about 3 years according to temperature change was proposed by proving the correlation between the expansion joint displacement of the upper road bridge and the cable tension of the lower railway bridge. The tension prediction results using the empirical formula for tension evaluation each cables proposed in this study were found to be in good agreement with the cable tension using the vibration method within 3%. Therefore, it was analyzed that it could be applied together with the vibration method that was an experimental technique, to predict and evaluate the cable tension in serviced railway steel composite bridge. As a result of applying the estimated temperature calculated by the empirical formula for expansion proposed in this study to the empirical formula, it was analyzed that a high level of reliability could be secured when compared with the vibration method. Therefore, it is judged that the empirical formula for cable tension evaluation reflecting the estimated temperature proposed in this study can be used to predict the tension of cables according to climate change in the future and establish a maintenance plan.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.05a
• /
• pp.241-248
• /
• 2004

In general, the salient features if the floating breakwater have excellent regulation of sea-water keeping the marine a1ways clean, up and dorm free movement with the incoming and outgoing tides, capable of being installed without considering the geological condition of sea-bed at any water depth, This study discusses the three dimensional wave transformation of the floating breakwater moored by catenary. Numerical method is based at the Green function method and eigenfunction expansion method. The validity of the present is confirmed by comparing it with the result of Ijima et a1.(1975) fer tensile maxed floating breakwater. According to the numerical results, drift and width of the floating breakwater affect at the wave transformation greatly, and incident wave of long period is well transmitted to the rear of the floating breakwater.

• Journal of Korea Water Resources Association
• /
• v.33 no.6
• /
• pp.805-814
• /
• 2000

A numerical model based on the boundary element method is employed to describe diffraction of monochromatic water waves due to varying topographies. The model is firstly verified by comparing obtained reflection and transmission coefficients of waves over a trench to those of the eigenfunction expansion method. The model is then used to investigate the Bragg reflection of waves over sinusoidally varying topographies. Calculated reflection coefficients are compared to available laboratory measurements and semi-theoretical results. A reasonably good agreement is observed.served.

• Journal of Korea Water Resources Association
• /
• v.36 no.3 s.134
• /
• pp.447-454
• /
• 2003

The Bragg reflection of monochromatic waves propagating over a rectangular-typed impermeable submerged breakwaters is numerically investigated by using the finite element method. The reflection coefficients calculated from the present model are compared with those of laboratory measurements and the eigenfunction expansion method. A good agreement is observed. The finite element model is also applied to calculate reflection coefficients according to variations of length and width of submerged breakwater.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.2 no.3
• /
• pp.146-154
• /
• 2010

In the present study, the wave excitation forces acting on an array of porous circular cylinders are examined based on diffraction problems. To calculate the wave forces, the fluid domain is divided into three regions i.e. a single exterior region, N interior regions and N beneath regions, and the diffraction in each fluid region is expressed by an eigenfunction expansion method with using 3-dimension liner potential theory (Williams and Li, 2000). Especially, the present method is extended to the case of an array of truncated porous circular cylinders to calculate the heave forces as well as surge and sway forces. To verify this method, the numerical results obtained by eigenfunction are compared with these results obtained by higher order boundary element method (Choi et al., 2000). The numerical results obtained by this study are in good agreement with those results. By changing the numbers of porous circular cylinders, the angle of incident wave and the porosity rate of circular cylinders, the wave excitation forces such as surge, sway and heave on an array of truncated porous circular cylinders are investigated.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.38 no.1
• /
• pp.201-216
• /
• 2013

Diffusion is a basic mathematical tool for modern financial engineering. The theory of the estimation methods for diffusion models is an important topic of the financial engineering. Many researches have been tried to apply the likelihood estimation method for estimating diffusion models. However, the likelihood estimation method for diffusion is complicated and needs much amount of computing. In this paper we develop the estimation methods which are simple enough to be compared to the Euler approximation method, and efficient enough statistically to be compared to the likelihood estimation method. We devise pseudo-likelihood and propose the maximum pseudo-likelihood estimation methods. The pseudo-likelihoods are obtained by approximating the transition density with normal distributions. The means and the variances of the distributions are obtained from the delta expansion suggested by Lee, Song and Lee (2012). We compare the newly suggested estimators with other existing estimators by simulation study. From the simulation study we find the maximum pseudo-likelihood estimator has very similar properties with the maximum likelihood estimator. Also the maximum pseudo-likelihood estimator is easy to apply to general diffusion models, and can be obtained by simple numerical steps.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.25-30
• /
• 2000

Residual stresses induced in U-bending and tube-to-tubesheet joining processes of PWR's steam generator row-1 tube were measured by X-ray method and Hole-Drilling Method(HDM). The stresses resulting from the Internal pressure and the temperature gradient in the steam generator were also estimated theoretically. In U-bent lesions, the residual stresses at extrados were induced with compressive stress(-), and its maximum value reached -319 MPa in axial direction at ${\psi}=0^{\circ}$ in position. Maximum tensile residual stress of 170MPa was found to be at the flank side at Position of${\psi}=90^{\circ}$, i.e., at apex region. In tube-to-tubesheet fouling methods, the residual stresses induced by the explosive joint method were found to be lower than that by the mechanical roll method. The gradient of residual stress along the expanded tube was highest at the. transition region, and the residual stress in circumferential direction was found to be higher than the residual stress in axial direction. Hoop stress due to an internal pressure between primary and secondary side was analyzed to be 76 MPa and thermal stress was 45 MPa.