• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.7
• /
• pp.94-102
• /
• 2007

With the recent expansion of electric capacity, troubles in the electric system threatening the stable electricity supply are rapidly increasing. However, most of the current short-circuit capacity calculations have been made manually. This research focuses on the development of a program which uses the Visual Basic. We can obtain the stability in the system diagram and the reliability of the loaded facilities by calculating an exact breaking capacity for each electric facility with this method. We expect that this research can be widely used for the design and construction of the electric facilities in the future.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.35 no.3
• /
• pp.37-49
• /
• 2007

This study investigated how external environmentally-friendly factors adopted to improve the quality of outdoor spaces have been designed and used in the construction of apartment complexes. The goal of this study is to determine what areas should be improved through environmentally-friendly ways to create natural outdoor spaces in apartment complexes and enhance their availability and usefulness. For this study, 21 environmentally-friendly factors were chosen and a checklist by specific item was prepared. This study examine how these items were applied to basic planning, detail design, and construction in 4 target areas. As a result, it was found that the development of environmentally-friendly residential areas was an ultimate goal of the project during basic planning and design. All target areas focused on developing an inner greens network, eco-pond, brook, and pedestrian track as well as the growth of a variety of plants. Some differences have been observed, however, in terms of method. Furthermore, due to economic and technological problems and poor construction site conditions, green walls/green roofs/pedestrian tracks/use of rainwater have not been properly promoted. These kinds of problems must be improved through the development of environmentally-friendly construction methods and materials, the expansion of natural grounds areas, economic support, a satisfactory repair and maintenance system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.2
• /
• pp.99-105
• /
• 2014

This paper proposes the reliability improvement of H-Bridge Multi-level (HBM) inverter. This reliability can be implemented through modularization of power circuit, distribution of controller, duplication of controller and communication, and continuous operation method in case of power cell failure for driving medium-voltage & high-power induction motor. It is shown that the modularization and expansion characteristics of the HBM inverter are improved since the individual inverter modules operate more independently when using the proposed concept. Also the fault tolerance is increased by using power cell bypass. The proposed design and control methods are described in detail and the validity of the proposed system is verified experimentally in various industrial fields.

• The Transactions of the Korea Information Processing Society
• /
• v.4 no.6
• /
• pp.1576-1588
• /
• 1997

The AIN(Advanced Intelligent Network) employs the Intelligent Network Application Protocol(INAP) which is transparent to services and low layer telecommunication networks. In this paper, we introduce the standard structure of INAP, which has flexible structure for easy expansion as AIN evolves, and we propose a structure of INAP by defining its functional elements. Also we design, analyze the INAP for AAB(Automatic Alternative Billing) service, which is one of the target services of IN CS-1 using object-oriented methodology. We use OMT method which is modified by ObjectGEODE in the analysis phase and SDL language for design. Furthermore we simulate the INAP system to prove that the system has been correctly built and supplies the service correctly for which it was designed.

• Proceedings of the KIEE Conference
• /
• 2000.11d
• /
• pp.700-702
• /
• 2000

The new design methodology of a hybrid fuzzy controller by means of the genetic algorithms is presented. In fuzzy controller which has been widely applied and used. in order to construct the best fuzzy rules that include adjustment of fuzzy sets, a highly skilled techniques using trial and error are required. To deal with such a problem, first, a hybrid fuzzy controller(HFC) related to the optimal estimation of control parameters is proposed. The HFC combined a PID controller with a fuzzy controller concurrently produces the better output performance than any other controller from each control output in steady state and transient state. Second, a auto-tuning algorithms is presented to automatically improve the performance of hybrid fuzzy controller, utilizing the simplified reasoning method and genetic algorithms. In addition, to obtain scaling factors and PID Parameters of HFC using GA, three kinds of estimation modes such as basic, contraction, and expansion mode are effectively utilized. The HFCs are applied to the first-order second-order process with time-delay and DC motor Computer simulations are conducted at step input and the performances of systems are evaluated and also discussed from performance indices.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.8 no.2
• /
• pp.240-253
• /
• 1996

The refrigeration cycle of automobile air-conditioners is simulated in an effort to provide a computational tool for optimum thermodynamic design. In the simulation, thermodynamic and heat transfer analysis was performed for the four major components : evaporator, condenser, compressor, and expansion valve. Effectiveness-NTU method was used for modeling both evaporator and condenser. The evaporator was divied into many subgrids and simultaneous cooling and dehumidifying analysis was performed for each grid to predict the performance accurately. Blance equations were used to model the compressor instead of using the compressor map. The performance of each component was checked against the measured data with CFC-12. Then, all the components were combined to yield the total system performance. Predicted cycle points were compared against the measured data with HFC-134a and the deviation was found to be less than 5% for all data. Finally, the system model was used to predict the performance of CFC-12 and HFC-134a for comparison. The results were very reasonable as compared to the trend deduced from the measured data.

• International Journal of Highway Engineering
• /
• v.17 no.6
• /
• pp.97-104
• /
• 2015

PURPOSES : Expressways experience chronic and recurring congestion, especially during weekends and holidays, because of the increased demands for leisure-related travel. The alternatives to solve chronic and recurring congestion may be three-fold: (1) physical expansion of expressway capacities, (2) road pricing, and (3) temporal and spatial distribution of traffic demands. Among these, the third alternative may be the most cost-effective method for the Korea Expressway Corporation (KEC) that can be achieved by using the existing ITS infrastructure. METHODS : KEC initiated a pilot study in which the traffic on congested expressways was managed by providing traffic condition information (i.e., travel times) of neighboring national highways for taking detours via variable message signs (VMS). This study aimed to estimate the detour rate, and the two pilot studies on Seohaean and Yeongdong expressways yielded many benefits. RESULTS : It was revealed that the total length of congestion segments decreased by 7.8 km, and the average travel speed increased by 5.3 km/h. CONCLUSIONS : Based on these findings, it was concluded that the propagation of detour information via VMSs during congestion hours can help reduce congestion on expressways and increase the benefits of the entire network.

• Polymer(Korea)
• /
• v.25 no.6
• /
• pp.826-832
• /
• 2001

In this study, PPy/gold/mylar type electroactive bi-layer actuator was prepared by the electrochemical polymerization of pyrrole onto the gold/mylar film and the actuation characteristics were studied using bending beam method. Conducting polymer-based actuators undergo volumetric changes due to the movement of dopant ions into the film during the electrical oxidation process. The bilayer films exhibited different actuation characteristics depending on dopant ion size. It was observed that the relatively small dopant ion (i.e. toluene sulfonate) moved into the PPy film at oxidized state, so volume expanded to result in bending motion. In case of the film having large dopant ion (i.e. dodecylbenzenesulfonate), volume expansion was observed at reduced state. This is due to the incorporation of $Na^+$ counterion with water molecules, while the large dopant ion was fixed in the film due to the limited mobility during tile redox process.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.694-699
• /
• 2002

In autobody assembly, thin-wall, tubular connections have been used for the frame structure. Recent interest in light materials, such as aluminum or magnesium alloys, has been rapidly growing for weight reduction and fuel efficiency. Due to higher thermal expansion coefficient, low stiffness/strength, and low softening temperature of aluminum and magnesium alloys, control of welding-induced distortion in these connections becomes a critical issue. In this study, the material sensitivity to welding distortion was investigated using a T-tubular connection of three types materials; low carbon steel (A500 Gr. A), aluminum alloy (5456-H116) and magnesium alloy (AZ91C-T6). An uncoupled thermal and mechanical finite element analysis scheme using the ABAQUS software program was developed to model and simulate the welding process, welding procedure and material behaviors. The predicted angular distortions were correlated to the cumulative plastic strains. A unique relationship between distortion and plastic strains exists for all three materials studied. The amount of distortion is proportional to the magnitude and distribution of the cumulative plastic strains in the weldment. The magnesium alloy has the highest distortion sensitivity, followed by the other two materials with the steel connection having the least distortion. Results from studies of thin-aluminum plates show that welding distortion can be minimized by reducing the cumulative plastic strains by preventing heat diffusion into the base metal using a strong heat sink placed directly beneath the weld. A rapid cooling method is recommended to reduce welding distortion of magnesium tubular connections.

• Journal of Welding and Joining
• /
• v.20 no.2
• /
• pp.109-115
• /
• 2002

In the case of using high temperature by coating ceramic/metal, large stress was produced due to difference of thermal expansion coefficient between those. And then lead to delamination. In order to relaxation of the stress A1$_2$O$_3$/SS316 composite powders with $10wt.%Al_2O_3$ compositional gradient and $10wt.%Al_2O_3$ agglomerated powder were made by spray drying method. These powders were sintered to improve the strength and to be plasma sprayed in order to fabricate the FGC(functionally graded coating). The influence of gun power, working distance and Ar pressure on the microstructure of the coating layer was studied in order to optimize the plasma spray conditions. It was proven that the optimum conditions were 40kw gun power, 5cm working distance and $100ft^3/h$ Ar flow for both powders. FGC with 10 compositional steps was fabricated and the total thickness was 1.3mm. FGC was heat treated at $1100^{\circ}C$for 10hours to evaluate the heat resisting characteristics.