• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.4
• /
• pp.175-180
• /
• 2011

A large AC generator is an important component of the power system. It is a need for research of AC generator protection relay for the next-generation ECMS and an efficient operation of protection control system. However, most of protection and control systems used in power plants have been still imported as turn-key and operated in domestic. This may cause the lack of the correct understanding on the protection systems and methods, and thus have difficulties in optimal operation. In this paper, over-excitation protection relaying is one of the protective factors in generator protection IED was presented. The cause and protection principles were dealt and, DFT-based gain compensation algorithm was adopted for the frequency measurement. The Republic of Korea 345kV modeling data by EMTP-RV was used for performance evaluation.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.11
• /
• pp.42-50
• /
• 2001

In this paper, a new technique and theory are proposed which correct the orientation (inclination of a vertical axis) of a cylinder in vertical-micro positioning device. An algorithm for determining the orientation of the cylinder with a pair of displacement sensor units is derived and two types of the correction methods are described. To assess the performance and efficiency of the developed correction technique, the compensation errors originated from the correction algorithm and the machined characteristics of cylinder surface are evaluated from the geometrical considerations and the statistical techniques. Based upon the evaluation results, the maximum compensation error is estimated for the orientation of cylinder and the optimum correction technique is derived.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.8
• /
• pp.768-773
• /
• 2012

Packet loss compensation techniques are increasingly important to stable remote control over wireless communication in WNCS (Wireless Networked Control Systems). Its time varying channels, limited bandwidth, interference, and poor signal not only leads to packet loss or latency, but also can negatively affect performance and system stability. This paper presents a compensation technique exploiting an EWMA (Exponentially Weighed Moving Average)-based value estimator to clarify the influence of packet loss on the overall WNCS behavior. As an example of actuator to be remotely controlled, a rotary-type inverted pendulum has been considered, and modeled. Performance evaluation results through Matlab/Simulink and Truetime co-simulation confirm the superiority of the proposed value estimation method over previous approaches.

• Journal of Industrial Technology
• /
• v.25 no.A
• /
• pp.183-189
• /
• 2005

In precision instrumentation system, an A/D conversion of signal conditioning has some problems.; offset and drift errors with environmental situation. This paper suggested a development of the Multi-Channel A/D Data Acquisition System and a method of the evaluation and the temperature compensation for the A/D converters with the specific analog and digital circuit including the software. Also, we have designed a hardware and a software filters with smart algorithm for better signal processing of the proposed system. Software approach was adopted to obtain the stable data from A/D converter. As shown in our experimental works, the proposed system is expected to be used in the industrial field where a high precision measurement is required.

• Journal of the Korean Home Economics Association
• /
• v.29 no.4
• /
• pp.131-150
• /
• 1991

The purpose of this study is to provide the basic data to measuring proper compensation for the homemakers. For this purpose, the value of household work is measured by variables and methods: overall substitute(OSE), specialised substitute (SSE), opportunity cost(OCE), reservation wage(RWE), subjective evaluation(SE). The Main Results are as follows: 1. The values by OSE, SSE, OCE, RWE and SE are respectively 497, 996, 676, 847, 616, 683, 707, 601 and 540, 366 won. 2. The values of homemakers are calculated individually by her demographic characteristics. 3, The values by SSE and OSE are increased in the order of type I.IV.III.II which are divided by the number of family member and age of homemaker.

• Journal of Power Electronics
• /
• v.8 no.2
• /
• pp.141-147
• /
• 2008

This paper deals with a new and improved control technique for shunt active filters (AF) used for compensating unwanted harmonic currents injected in the mains due to nonlinear varying loads. This work is motivated by the need to find a permanent solution to the rigorous hit and trial method for evaluating system parameters in an indirect control of AF. A fuzzy pre-compensated PI (Proportional-Integral) controller is used to fuzzify the reference DC voltage of AF to the controller input so that the overshoots and undershoots in its DC link voltage are minimized and the settling time is improved. A three-phase diode rectifier with R-L (Resistive-Inductive) load is used as a non-linear load to study the effectiveness of the proposed controller of the AF. Robustness to filter parameter variations, insensitivity to controller parameter variations, and transient response has been taken as performance evaluation parameters. The results are shown through simulations in Matlab using power system block sets to demonstrate the capability of the proposed controller of the AF.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.12
• /
• pp.1086-1092
• /
• 2012

It has been studied for DGPS/INS(Differential Global Positioning System/Inertial Navigation System) to offer the more precise and reliable navigation data with the aviation industry development. The flight performance evaluation of navigation system is very significant because the reliability of navigation data directly affect the safety of aircraft. Especially, the high-level navigation system, as DGPS/INS, need more precise flight performance evaluation method. The performance analysis is performed by comparing between the DGPS/INS navigation data and reference trajectory which is more precise than DGPS/INS. The GPS receiver, which is capable of post-processed CDGPS(Carrier-phase DGPS) method, can be used as reference system. Generally, the DGPS/INS is estimated the CG(Center of Gravity) point of aircraft while the reference system is output the position of GPS antenna which is mounted on the outside of aircraft. For this reason, estimated error between DGPS/INS and reference system will include the error due to lever arm. In order to more precise performance evaluation, it is needed to compensate the lever arm. This paper presents procedure and result of flight test which includes lever arm compensation in order to verify reliability and performance of DGPS/INS more precisely.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.292-295
• /
• 2003

Conventional methods in time / frequency domain for evaluating the compensation performance of active power filters are not provided easy solutions. So, the authors have previously proposed 3-D current coordinates which is composed into active component, fundamental reactive component and distorted component of nonlinear loads current. This method has excellent performance, but can not evaluate the characteristics of nonlinear load current whether it is inductive or capacitive. Therefore, To overcome problems mentioned previously, this paper deals with the simple Average power theory and the expanded 3-D current coordinates for evaluating the compensation performance of active power filters. To confirm the validity, active power filters simulator is developed using C-language. From the simulation, results are discuss their utility.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.17 no.5
• /
• pp.39-53
• /
• 2007

The purpose of this paper is the development of a compensation algorithm by which the interoperability of fingerprint recognition can be improved among various different fingerprint sensor. In order to compensate for the different characteristics of fingerprint sensor, an initial evaluation of the sensors using both the ink-stamped method and the flat artificial finger pattern method was undertaken. This paper proposes Common resolution method and Relative resolution method for compensating different resolution of fingerprint images captured by disparate sensors. Both methods can be applied to image-level and minutia-level. In order to compensate the direction of minutiae in minutia-level, Unit vector method is proposed. The EER of the proposed method was improved by average 64.8% better than before compensation. This paper will make a significant contribution to interoperability in the system integration using different sensors.

• The KIPS Transactions:PartB
• /
• v.11B no.1
• /
• pp.7-12
• /
• 2004

This thesis studies about thinning compensation and the removal of pseudo minutiae using ridge trace. As for the process of thinning compensation, first, it removes unnecessary pixel when 8-neighbor connection sum among the pixels with the crossing count number 6 is not 3. Second, it deals with repeatedly until there is no pixel to remove while tracing the ridge, beginning with the pixel equivalent to the ridge and the pixel with the crossing count number 2 among the 8 pixels around the pixels with the crossing count number 6. When the thinning compensation is finished, it extracts substitute minutiae to use the crossing count number and the 8-neighbor connection sum. Among the extracted substitute minutiaes, it extracts the real minutiae to utilize the pseudo minutiae removal algorithm again. It compares with the existing method for the performance evaluation of proposal method. By the experimental results, The proposal method indicated that a degree of thinning is excellent and a lot of minutiaes were removed.