• Electrical & Electronic Materials
• /
• v.7 no.5
• /
• pp.425-429
• /
• 1994

In this paper, we study on the plasma polymerized styrene as a negative electron-beam resist. Plasma polymerized thin film was prepared using an interelectrode inductively coupled gas-flow type reactor. We show that polymerization parameters of thin film affect sensitivity and etching resistance of the resist. Molecular weight distribution of plasma polymerized styrene is 1.41-3.93, and deposition rates of that are 32-383[.angs./min] with discharge power. Swelling and etching resistance becomes . more improved with increasing discharge power during plasma polymerization. Etch rate by RIE is higher than that by plasma etching.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.4
• /
• pp.19-23
• /
• 2012

Silicon substrate for light emitting diodes (LEDs) has been the tendency of LED packaging for improving power consumption and light output. In this study, a low cost and high throughput Si through via fabrication has been demonstrated using a wet etching process. Both a wet etching only process and a combination of wet etching and dry etching process were evaluated. The silicon substrate with Si through via fabricated by KOH wet etching showed a good electrical resistance (${\sim}5.5{\Omega}$) of Cu interconnection and a suitable thermal resistance (4 K/W) compared to AlN ceramic substrate.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.38.1-38.1
• /
• 2009

Plasma etching is an essential process for electronic device industries and the particulate contamination during plasma etching has been interested as a big issue for the yield of productivity. The oxynitride glasses have a merit to prevent particulate contamination due to their amorphous structure and plasma etching resistance. The YSiAlON oxynitride glasses with increasing nitrogen content were manufactured. Each oxynitride glasses were fluorine-plasma etched and their plasma etching rate and surface roughness were compared with reference materials such as sapphire, alumina and quartz. The reinforcement mechanism of plasma etching resistance of the YSiAlON glasses studied by depth profiling at plasma etched surface using electron spectroscopy for chemical analysis. The plasma etching rate decreased with nitrogen content and there was no selective etching at the plasma etched surface of the oxynitride glasses. The concentration of silicon was very low due to the generation of SiF4 very volatile byproduct and the concentration of aluminum and yttrium was relatively constant. The elimination of silicon atoms during plasma etching was reduced with increasing nitrogen content because the content of the nitrogen was constant. And besides, the concentration of oxygen was very low on the plasma etched surface. From the study, the plasma etching resistance of the glasses may be improved by the generation of nitrogen related structural groups and those are proved by chemical composition analysis at plasma etched surface of the YSiAlON oxynitride glasses.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.3
• /
• pp.57-62
• /
• 2022

The plasma resistance of multi-component glasses containing La, Gd, Ti, Zn, Y, Zr, Nb, and Ta was analyzed in this study. The plasma etching was performed via inductively coupled plasma-reactive ion etching (ICP-RIE) using CF₄/O₂/Ar mixed gas. After the reaction, the glass with a low fluoride sublimation temperature and high content of P, Si, and Ti elements showed a high etching rate. On the other hand, the glass containing a high fluoride sublimation temperature component such as Ca, La, Gd, Y, and Zr exhibited high plasma resistance because the etch rate was lower than that of sapphire. Glass with low plasma resistance increased surface roughness after etching or nanoholes were formed on the surface, but glass with high plasma resistance showed little change in surface microstructure. Thus, the results of this study demonstrate the potential for the development of plasma-resistant glasses (PRGs) with other compositions besides alumino-silicate glasses, which are conventionally referred to as plasma-resistant glasses.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.6
• /
• pp.1465-1468
• /
• 2010

The wet etching is a process using chemical solution and occurring chemical reaction on substrate surface. when we do wet etching process, we have to consider stoichiometry, etching time and temperature of etchant for good resolution. In this experiment, we used Cr, Al andIndium-tin-oxide (ITO) metal and we deposited them with DC sputtering machine. The Cr thin film metal thickness is about $1300{\AA}$, ITO films show a low electrical resistance and high transmittance in the visible range of an optical spectrum and Ai film is used for signal line. We measured and analysed wet etching properties on the metal thin films.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.4
• /
• pp.77-82
• /
• 2022

During etching process of PCB, the electroplated copper line and seed layer copper have different etching rates and it caused the over etching of copper line as well as undercut of lines. In this research, the effects of etchants composition on copper etching characteristics were investigated. The optimum concentration of hydrogen peroxide and sulfuric acid of etchants were obtained using polarization and OCV (open circuit voltage) analysis for both rolled copper and electroplated copper. The inhibiting effects of different inhibitors were investigated using OCV and ZRA (zero resistance ammeter) analysis. The galvanic current between electroplated copper and seed layer copper were measured using ZRA method. Inhibitors for least galvanic current could be chosen based on galvanic coupling in ZRA analysis.

• Composites Research
• /
• v.34 no.6
• /
• pp.387-393
• /
• 2021

This paper investigated the electrical properties of multiwall carbon nanotube reinforced polydimethylsiloxane (CNT-PDMS) strain sensors with copper electrodes on the wet-etched surface. MWCNT-PDMS strain sensors were fabricated according to the wt% of MWCNT. Surfaces on the electrode area were wet-etched with various etching duration and silver epoxy adhesives were spread on the wet-etched surface. Finally, we attached the copper electrodes to the MWCNT-PMDS strain sensors. We checked the electric conductivities by the two-probe method and sensing characteristics under the cyclic loading. We observed the electric conductivity of MWCNT-PDMS strain sensors increased sharply and the scattering of the measured data decreased when the surface of the electrode area was wet-etched. Initial resistances of MWCNT-PDMS strain sensors were inversely proportion to wt% of MWCNT and the etching duration. However, the resistance changing rates under 30% strain increased as wt% of MWCNT and the etching duration increased. Decreasing rate of the electric resistance change after 100 repetitions was smaller when wt% of MWCNT was larger and the etching duration was short. This was due to the low initial resistance of the MWCNT-PMDS strain sensors by the wet-etching.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.49.1-49.1
• /
• 2010

The particle generation during the plasma enhanced process is highly considered as serious problem in the semiconductor manufacturing industry. The material for the plasma processing chamber requires the plasma etching characteristics which are homogeneously etched surface and low plasma etching depth for preventing particulate contamination and high durability. We found that the materials without grain boundaries can prevent the particle generation. Therefore, the amorphous material with the low plasma etching rate may be the best candidate for the plasma processing chamber instead of the polycrystalline materials such as yttria and alumina. Three glasses based on $SiO_2$ and $Al_2O_3$ were prepared with various rare-earth elements (Gd, Y and La) which are same content in the glass. The glasses were plasma etched in the same condition and their plasma etching rate was compared including reference materials such as Si-wafer, quartz, yttria and alumina. The mechanical and thermal properties of the glasses were highly related with cationic field strength (CFS) of the rare-earth elements. We assumed that the plasma etching resistance may highly contributed by the thermal properties of the fluorine byproducts generated during the plasma exposure and it is expected that the Gd containing glass may have the highest plasma etching resistance due to the highest sublimation temperature of $GdF_3$ among three rare-earth elements (Gd, Y and La). However, it is found that the plasma etching results is highly related with the mechanical property of the glasses which indicates the cationic field strength. From the result, we conclude that the glass structure should be analyzed and the plasma etching test should be conducted with different condition in the future to understand the plasma etching behavior of the glasses perfectly.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12
• /
• pp.1097-1102
• /
• 2003

In this paper, we used only PR as etching mask, while it used usually Cr/AU as etching mask, and in order to fabricate a photosensor has the increased sensitivity, we investigated on the sensitivity of general type and p-i-n type diode. we designed microchannel size width max 10um, min 5um depth max 10um, reservoir size max 100um, min 2mm. Fabrication of microfluidic devices in glass substrate by glass wet etching methods and glass to glass fusion bonding. The p-i-n diode has higher sensitivity than photodiode, Considering these results, we fabricated p-i-n diodes on the high resistive(4㏀$.$cm) wafer into rectangle and finger pattern and compared internal resistance of each pattern. The internal resistance of pin diode can be decreased by the application of finger pattern has parallel resistance structure from 571Ω to 393Ω.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.455-456
• /
• 2008

In this study, we report that an electrical properties of OLEDs was investigated by the surface etching method of ITO Layer. The electrical properties of OLEDs was measured by IVL and optical properties by EL spectrum. The fundamental structure of OLEDs was ITO anode/TPD(400$\breve{A}$)/$Alq_3(600\breve{A})$/LiF(5$\breve{A}$)/Al(1200$\breve{A}$) cathode. The threshold voltage was low value according to the low resistance of surface. The luminance was increased by decreased surface resistance.