• 화약ㆍ발파
• /
• 제27권1호
• /
• pp.38-46
• /
• 2009

최근 진동 소음을 저감하는 공법으로 초시의 정확성과 초시부여의 자율성을 가진 전자뇌관을 이용하는 공법(OBM ; Orechestra Blasting)이 소개되었다. 파형합성프로그램은 전자뇌관의 지연초시를 결정할 수 있으며 결정된 초시를 이용하여 실 발파와 유사한 환경에서의 시뮬레이션을 수행, 최적초시 상태의 진동 속도를 예측할 수 있다. 본 연구에서는 파형합성프로그램을 통해 진동을 제어하는 최적초시를 얻고 실제 발파작업 시의 진동치를 예측하고자 하였다.

• 환경영향평가
• /
• 제20권5호
• /
• pp.641-649
• /
• 2011

The ground vibration has effect on the human body and the nearby structure. However, it was very difficult to estimate the damage of structure caused by the vibration. Especially, ground vibration must be estimated on the bottom of structure because it was made up of several mediums. In this study, it was considered about the shock vibration on medium characteristics as calculating the peak particle velocity and analysing the vibration waveform. The results are as follows : Firstly, the correlation coefficient of PPV(Peak Particle Velocity) and SD(Scaled Distance) was very high at the vertical component, which was represented to 0.991 in general ground medium and each 0.989, 0.961, 0.925 in concrete medium. And also, the vibration waveform at the vertical component was very good in all mediums. Secondly, the vibration waveform at the longitudinal component was represented to a great amplitude and phase difference in all mediums. It was considered that the vibration waveform occurred the damping when particle velocity by shock vibration was propagated through other medium. Thirdly, the vibration waveform in concrete medium was represented to variation of amplitude in the order of RC medium, NC=H medium, NC=S medium at the vertical component. It was considered that the particle velocity propagated fast when a medium have a big strength and density.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.485-492
• /
• 2005

Since blast-induced vibration may cause serious problem to the rock mass as well as the nearby structures, the prediction of blast-induced vibration and the stability evaluation must be performed before blasting activities. Dynamic analysis has been Increased recently in order to analyze the effect of the blast-induced vibration. Most of the previous studies, however, were based on the continuum analysis unable to consider rock joints which significantly affect the wave propagation and attenuation characteristics. They also adopted pressure curves estimated by theoretical or empirical equations as input detonation load, thus there were very difficult to reflect the characteristics of propagating media. In this study, therefore, we suggested a discontinuum dynamic analysis technique which uses velocity waveform obtained from a test blast as an input detonation load. A distinct element program, UDEC was used to consider the effect of rock joints. In order to verify the validity of proposed method, the test blast was simulated. The predicted results from the proposed method showed a good agreement with the measured vibration data from the test blast Through the dynamic numerical modelling on the planned road tunnel and slope, we evaluated the effect of blast-induced vibration and the stability of rock slope.

• 환경영향평가
• /
• 제21권5호
• /
• pp.609-615
• /
• 2012

In recent years, the development of computer technique was possible to the simulation analysis of the structure caused by ground vibration. Generally, finite element method(FEM) has been used in these structural analysis. In this study, it was calculated to the vibration energy as measuring vibration waveform, and estimated about principal stress due to medium characteristics of the ground as processing dynamic analysis by the vibration energy. The results are as follows : Firstly, the principal stress distribution in all mediums was different due to a medium condition, and the principal stress at concrete medium was represented to difference due to physical characteristics. Secondly, the principal stress by time increasing was represented to maximum amplitude within 0.03 second. And also, the principal stress after maximum amplitude was very large at concrete medium, which was considered to be formed compression or tension range at a medium boundary. Thirdly, the variation of principal stress at concrete medium was represented in the order of RC medium, NC=H medium, NC=S medium. It was considered that the vibration energy propagated fast when a medium have a big elasticity and density.

• 화약ㆍ발파
• /
• 제39권4호
• /
• pp.1-11
• /
• 2021

본 연구에서는 기계식 해체공법을 적용한 슬래브 해체 시 발생하는 진동을 분석하기 위해 진동 자료를 획득하였다. 획득한 진동 자료는 부착장치에 따라 구별하여 파형 및 우세주파수 분석을 수행하였고, 작업위치와 계측위치 사이의 거리를 측정하는 방법을 달리하여 상관관계를 분석하였다. 부착 장치 별 파형분석 결과 장비 작업에 의한 진동 파형의 위상 변화는 거의 없고 진동속도의 크기인 진폭의 변화만 일어났으며, 주파수 분석 결과 압쇄기를 사용한 경우 브레이커를 사용한 경우에 비해 주파수 대역이 낮으며, 해체 대상 건축물의 고유 진동수와 주파수 대역이 근접하였다. 상관관계 분석결과 작업 위치와 계측위치의 이격거리는 상호 간의 직선거리가 아닌 실제 건축물을 따라 진동이 전파하는 경로로 평가해야 높은 상관성을 보임을 확인하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2006년도 전력전자학술대회 논문집
• /
• pp.319-322
• /
• 2006

This paper deals with the HVDC system fault analysis and the sound noise analysis. In this paper, the reasons of the audible noise and vibration were analyzed, the fault waveform were analyzed using DTR (Digital Transient Recorder). Finally, using the fault current waveform and the vibration equation, the reason of crack of smoothing reactor support is estimated.

• 조명전기설비학회논문지
• /
• 제20권7호
• /
• pp.21-28
• /
• 2006

본 논문은 HVDC 시스템의 고장 시 고장 원인과 소음의 원인 및 기계적인 균열에 관하여 분석한 논문이다. 본 논문에는 전기설비의 소음과 진동의 원인을 분석하였고, 시스템의 고장을 정량적으로 분석하였다. 최종적으로 고장전류와 소음과 진동 방정식을 이용하여 Smoothing 리액터의 지지물의 균열의 원인이 분석되었다.

• 한국소음진동공학회논문집
• /
• 제15권12호
• /
• pp.1389-1397
• /
• 2005

Since blast-induced vibration may cause serious problem to the rock mass as well as the nearby structures, the prediction of blast-induced nitration and the stability evaluation must be performed before blasting activities. Dynamic analysis has been increased recently in order to analyze the effect of the blast-Induced vibration. Most of the previous studies, however, were based on the continuum analysis unable to consider rock joints which significantly affect the wave propagation and attenuation characteristics. They also adopted pressure corves estimated tv theoretical or empirical equations as input detonation load, thus there were very difficult to reflect the characteristics of propagating media. In this study, therefore, we suggested a dynamic distinct element analysis technique which uses velocity waveform obtained from a test blast as an input detonation load. A distinct element program, UDEC was used to consider the effect of rock joints. In order to verify the validity of proposed method, the test blast was simulated. The predicted results from the proposed method showed a good agreement with the measured vibration data from the test blast. Through the dynamic numerical modelling on the planned road tunnel and slope, we evaluated the effect of blast-induced nitration and the stability of rock slope.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1994년도 Proceedings of the Korea Automatic Control Conference, 9th (KACC) ; Taejeon, Korea; 17-20 Oct. 1994
• /
• pp.593-596
• /
• 1994

When a force impulse acting on a massive and plex object is measured with a dynamometer, be resonant vibration of the measurement system often leads to serious inaccuracies. A more accurate measurement is obtained when the transfer function ,of the object-dynamometer system is used to compensate for the error in the dynamometer's output signal. The natural frequency and the damping coefficient of the transfer function are estimated by analyzing the waveform of the free damped vibration period after the loading of the force has ended. The residue of the system is determined such that the compensated force spectrum becomes smooth within a neighborhood of the natural frequency. The effectiveness of this signal processing method is experimentally tested on a hammer impulse, under the assumption that the hammer's high resonant frequency accurately models the problems encountered in force impact measurement. The compensation method is used to derive a improved estimate of the hammer impulse.

• 한국소음진동공학회논문집
• /
• 제25권6호
• /
• pp.399-405
• /
• 2015

In this work we use the mode decomposition technique employing chirplet transform, which is able to separate the individual modes from dispersive and multimodal waveform measured with the magnetostrictive sensor. The mode decomposition technique is also used to estimate the time-frequency centers and individual energies of the reflection, which would be used to locate and characterize axial defects. The arrival times of the separated modes are calculated and the axial defect lengths can be evaluated by using the estimated arrival time. Results from an experiment on a carbon steel pipe are presented and it is shown that the accurate and quantitative defect characterization could become enabled using the proposed technique.