• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1014-1017
• /
• 2006

Admittance Spectroscopic analysis was applied to study the effect of LiF buffer layer and to model the equivalent circuit for $ITO/Alq_3/LiF/Al$ device structure. The admittance spectroscopic analysis of the devices with LiF layer shows reduction in contact resistance $(R_C)$, parallel resistance $(R_P)$ and increment in parallel capacitance $(C_P)$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.5
• /
• pp.398-405
• /
• 2002

The degradation characteristics of MgO additive for the ZnO ceramic devices fabricated by the standard ceramic techniques are investigated in this study. These devices were made from basic Matsuoka's composition. Especially, MgO was added to analyze the degradation characteristics and devices were sintered in air at $1200^{\circ}C$. The conditions of DC degradation test were $115\pm2^{\circ}C$ for 12h. Using XRD and SEM, the phase and microstructure of samples were analyzed, respectively. The elemental analysis in the microstructures was performed by EDS, E-J analysis was used to determine $\alpha$. Frequency analysis was accomplished to understand the relationship between $R_G$ and $R_B$ with the electric stress at the equivalent circuit.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.1
• /
• pp.27-33
• /
• 1999

Compact fluorescent lamps are very sensitive to the variation of ambient temperature. This paper investigates the temperature characteristics of a 15[W] compact fluorescent lamp, and compensates the variation of light output by frequency control of its electronic ballast. Circuit parameters for the inverter of the electronic ballast are obtained by analyzing the R-L-C equivalent circuit for the inverter and the lamp. The optimum ratio of the two capacitance($C_1$/$C_2$), which are connected with the lamp in series and in parallel, respectively, is determined which consideration of the temperature variation within a range of 10~35[$^{\circ}C$]. As a result a value of 10 for the ratio is obtained at an operating frequency of 57[kHz], and with this value the frequency control works well for temperature compensation. Its validity is verified by investigating light output stabilization characteristics resulting from frequency control of the lamp at various temperatures.

• Journal of Korea Multimedia Society
• /
• v.21 no.1
• /
• pp.34-44
• /
• 2018

An early detection of intravenous (IV) infiltration is essential to minimize the injuries during infusion therapy, which is one of the most important tasks for nurses in nursing settings. We report that bioelectrical impedance analysis is useful in the early detection of infiltration at puncture sites. When infiltration was intentionally induced in the vein of a pig's posterior ear, impedance parameters (R, $X_C$, $C_m$) showed significant differences before and after infiltration. In particular, the relative resistance ($R/R_{BI}$) decreased significantly at infiltration and then slowly decreased. This indicates that the vein in pig's ear is thin and the amount of surrounding subcutaneous tissue, and hence the infiltrated solution accumulates slowly after infiltration. However, when infiltration was induced in the vein of human's forearm, the relative resistance at 20 kHz decreased gradually over time. In the $R-X_C$ graph, the positions in the case of infiltration induced in the pig' ear shifted rapidly before and after infiltration, whereas the positions in the case of infiltration induced in the human's forearm moved gradually during infiltration. Our findings suggest that the impedance parameters (R, $R/R_{BI}$, $X_C$, R vs. $X_C$, and $C_m$) are effective indicators to detect the infiltration early in a non-invasive and quantitative manners.

• Proceedings of the KIEE Conference
• /
• 2008.11a
• /
• pp.92-94
• /
• 2008

This paper introduces the modeling of grid-connected photovoltaic(PV) generation using Matiab/Simulink. The model is based on the equivalent circuit of the PV solar cell including the effects of solar irradiation and temperature changes. The PV arrays are modeled to be built up with the series/parallel combination of PV solar cell and are connected to the distribution system via an inverter. The simulation results show that the typical characteristics and outputs of the PV arrays are accurate.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.957-959
• /
• 2005

A noise reduction equipment in power systems was device combined in a passive element such as the form of L, R and C. A analysis of frequency characteristics for the transformer models shall be considered the additional capacitance between the windings($C_{ps}$), terminals($C_s$), and winding-ground($C_g$). A noise in transformer is modeled by take account into the different frequency. In case of the high frequency, transformer windings with stray capacitance have lower impedance. Therefore a noise is transferred from primary winding to secondary winding. Noise Cut Transformer(NCT) was the noise reduction device and was normally single phase two-winding type transformer. We analyzed frequency characteristics using the nodal network analysis with the equivalent circuit and the simulation of the MATLAB.

• Journal of the Korean Chemical Society
• /
• v.43 no.1
• /
• pp.23-29
• /
• 1999

The Al oxide layer formed in 1M $H_2SO_4$ solution and the influence of applied frequency for electrodeposition of Mn on Al oxide layer were characterized using by impedance spectroscopy. Mn compounds were electrodeposited at the base of pores during deposition with applied low frequency voltage. For the Mn deposited oxide layer at 6OHz and 5Hz in 1 g/L $KMnO_4$ solution, in equivalent circuit for interpretation, the resistance ($R_2$) and capacitance ($C_2$) were considered to be due to deposition of Mn on base of pore. The electrochemical behavior of barrier layer and porous oxide layer on Al have been characterized by capacitance ($C_b$) and Young capacitance ($C_Y$) in equivalent circuit model.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.157-160
• /
• 2001

Three sets of ZnO ceramic devices (reference samples with Matsuoka\`s composition; added 7o MgO, A1$_2$O$_3$, SiO$_2$) have been prepared by the conventional mixed oxide route. These additives were determined by the factors of valences and ionic radiuses. DC accelerated degradation test was performed for analysis of degradation characteristics versus the various additives. The conditions of DC degradation test were 115${\pm}$2$^{\circ}C$ for 12h. Using XRD and SEM, the Phase and microstructure of samples were analyzed respectively. E-J analysis was used to determine ${\alpha}$. Frequency analysis was accomplished to understand the relationship between R$\sub$g/ and $R_{b}$ with the electric stress at the equivalent circuit.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.113-115
• /
• 1995

The calculations of the temperature rise in the armature have long been considered among some of the most important problems in the design of the rotating machine. Despite the many methods of calculation propose, very few have been used in the actual design. In most cases, These methods are inadequate for measuring a wide range of temperature distribution because of the complicated structure of the machine. In this paper, the armature is divided into seven portions, and the thermal equivalent circuit is introduced as a simulation of the armature. The test machine is 1000Kw salient-pole synchronous generator.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.258.1-258.1
• /
• 2015

ITO가 코팅된 PET 기판 위에 P3HT:PCBM으로 이루어진 bulk heterojunction 유기 태양전지 소자를 만들었다. 이렇게 만들어진 유기 태양전지의 flexibility 특성을 측정하기 위해서, 태양전지 소자를 반지름이 다른 원통에 감아서 휘어지게 한 후 AM 1.5의 조명 하에서 전류-전압 특성을 관측하고 소자의 임피던스 분석도 측정하였다. 이때 flexibility 특성 측정의 일관성을 위하여, 단 하나의 유기 태양전지 소자를 만들고, 이 소자를 반지름이 큰 원통에서 부터 휘게 하고난 후 소자의 특성을 측정하고, 점차 작은 원통으로 바꾸어 가면서 측정을 진행하였다. 임피던스 분석 실험 자료로부터 shifted two semicircles이라는 equivalent circuit model를 분석하고 난 후, 이 회로를 구성하는 구성 성분-R(s), R(low f), R(hi f), C(low f), C(hi f)-값의 변화를 원통의 반지름의 변화에 따라 분석하였다. 반지름이 0.75cm일 때, power conversion efficiency (PCE) 값은 초기값에 비해 약 1/3로 줄었고, 반지름이 0.5cm일 때는 약 10%로 줄어 들었다. 나머지 1~2 cm일 때는 거의 변화가 나타나지 않았다. 휘어짐에 따른 이러한 태양전지의 특성의 변화를 임피던스 분석의 Cole-Cole plot의 저 주파수 영역의 반원의 반지름에 가장 큰 영향을 받음을 확인하였고, 저항과 capacitance 값의 변화에 따른 특성에 대해 이번 발표에서 더 자세히 설명할 예정이다.